Paradyne 5620 RTUの取扱説明書

20ページ 0.23 mb
ダウンロード

ページに移動 of 20

Summary
  • Paradyne 5620 RTU - page 1

    TM 1 Hotwire  5620 RTU Customer Premises Installation Instructions Document Number 5620-A2-GN10-30 December 1998 Before Y ou Begin The Hotwire  5620 RTU (Remote T ermination Unit) interoperates with the Hotwire 8510 DSL Card in the DSLAM (Digital Subscriber Line Access Multiplexer) system. An optional POTS (Plain Old T elephone Service) split ...

  • Paradyne 5620 RTU - page 2

    2 Package Checklist V erify that your package contains the following: - Model 5620 Remote T ermination Unit (RTU) - DSL interface cable with RJ1 1 connectors - Power cord with power transformer - T wo ferrite chokes What Does the Hotwire RADSL R TU Do? The Hotwire 5620 RTU is a component in the Hotwire DSL Access System. This system provides high-s ...

  • Paradyne 5620 RTU - page 3

    3 98-16105 Punchdown Block or NID DSL Jack RTU Customer Premises (CP) DSL Ethernet Crossover Cable Ethernet Cable or Central Office (CO) Demarcation Point Local Loop CP POTS Splitter DSL – Digital Subscriber Line POTS – Plain Old T elephone Service NID – Network Interface Device R TU – Remote T ermination Unit POTS End-user Systems Network ...

  • Paradyne 5620 RTU - page 4

    4 DSL Access without a POTS Splitter When the Hotwire 5620 RTU is installed without a POTS splitter , a second telephone wiring pair is needed for DSL access. 97-15345-02 Punchdown Block or NID DSL Jack RTU Customer Premises (CP) POTS DSL Ethernet Crossover Cable Ethernet Cable or Central Office (CO) Demarcation Point Local Loop Hub New Wiring Conn ...

  • Paradyne 5620 RTU - page 5

    5 Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connected from the customer premises side of the punchdown block or the NID to the DSL jack. T ypically , the punchdown block is installed in commercial locations and the NID is installed in residential locations.  Procedur e 1. Access the ...

  • Paradyne 5620 RTU - page 6

    6 3. Locate the DSL pair of T1/R1 connectors on the customer premises side of the NID or punchdown block. Attach the wiring that will be connected to the DSL jack. In the following example, a NID is used without a POTS splitter . It includes an existing POTS line and a second pair installed for DSL access. DSL/PO TS Access from Local Loop Wiring to ...

  • Paradyne 5620 RTU - page 7

    97-15300a RJ11 W all Jack or 7 The Hotwire 5620 RTU connects to the local loop via wiring from the demarcation point to an RJ1 1 wall jack. The DSL twisted-pair wiring from the local loop terminates at a new or existing wall jack. It may be necessary to install a standard single RJ1 1 jack or replace a single jack with a double RJ1 1 wall jack. 97- ...

  • Paradyne 5620 RTU - page 8

    8 Installing the Hotwire 5620 R TU Place the Hotwire 5620 RTU on a flat surface with clearance for the rear connectors.  Procedur e 1. Use the supplied RJ1 1 6-pin interface cable for the DSL connection. Insert one end of the cable into the jack labeled DSL. Insert the other end into the wall jack labeled DSL. 97-15300-01 DSL Jack POWER ETHERNET ...

  • Paradyne 5620 RTU - page 9

    9 2. Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the cable into the jack labeled ETHERNET .  Use a straight-through cable and connect the other end to an Ethernet hub, or 97-15303-01 Ethernet Hub Ethernet Line PO WER ETHERNET DSL Hotwire RTU Ethernet Cable  Use an Ethernet crossover cable and connect the other e ...

  • Paradyne 5620 RTU - page 10

    496-14952 97-15303c Ethernet Line PO WER ETHERNET DSL Hotwire RTU F errite Choke 10 3. Place the large ferrite choke on the Ethernet cable as closely as possible to the RTU. Pass the Ethernet cable through the ferrite choke twice, creating a loop as shown. 4. Close the two halves around the cable and snap the ferrite choke shut. Press down on the p ...

  • Paradyne 5620 RTU - page 11

    11 Optional R TU W all Placement The Hotwire 5620 RTU is designed for tabletop placement. The R TU can also be mounted on a wall. T o mount an RTU, you will need: - Three slotted-head #6 self-threading screws with molly bolts - Drill and 3/16 I drill bit for the molly bolts - Screwdriver A template with the dimensions for the three screws is provid ...

  • Paradyne 5620 RTU - page 12

    12 R TU Hardwar e T emplate F ront (LEDs) 98-16171 5.43" 7.55" T o Bottom Hole ...

  • Paradyne 5620 RTU - page 13

    13 Power -On When power is applied, the RTU performs self-diagnostics and the PWR LED is on. The self-diagnostics includes a power-on self-test. During the power-on self-test, all of the LEDs turn on for one second. TST DSL ETHERNET ALM PWR TM 98-15835 P ower – g reen Alarm – red T est – y ellow Digital Subscriber Line – green Ethernet Link ...

  • Paradyne 5620 RTU - page 14

    14 T roubleshooting LED Symptom Action All LEDs are on. The RTU may be in download mode. W ait ten minutes. If LEDs remain on after ten minutes and the RTU is not in download mode, the RTU is not functional. Contact the NSP . ALM LED remains on. The power-on self-test may have failed. Unplug the unit and reapply power . If the alarm LED is still on ...

  • Paradyne 5620 RTU - page 15

    98-16055a 8-Pin Plug Ethernet Cable Pin #1 Pin #8 15 Cables & Connectors Use standard twisted-pair CA T3 or better cables. This section is reference information.  The Ethernet interface connector uses an 8-pin, non-keyed modular plug. — T o connect the RTU to an Ethernet hub, use the straight-through connection. 8-Pin Straight-Through Conn ...

  • Paradyne 5620 RTU - page 16

    98-15304-01 6-Pin RJ11 Plug DSL Cable Pin #1 Pin #6 16  The DSL interface connector uses a 6-pin, non-keyed modular plug. RJ1 1 6-Pin Connector Pin # Function 1 & 2 Not used 3 DSL Ring 4 DSL T ip 5 & 6 Not used Model 5620 R TU T echnical Specifications Item Specification * Height x Width x Depth 1.43 ″ x 6.00 ″ x 8.75 ″ (3.64 cm x ...

  • Paradyne 5620 RTU - page 17

    17 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3. Do n ...

  • Paradyne 5620 RTU - page 18

    18 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal Communications Commission’s Rules. This compliance information statement pertains to the following products: T rade Name: Hotwire Model Number: 5620-A2-200 This device complies with Part 15 of the FCC Rules. Operat ...

  • Paradyne 5620 RTU - page 19

    19 Canada EMI W arnings ! W ARNING: T o Users of Digital Apparatus in Canada: This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial brouilleur du Canada. Notice to Users of the Canadian T el ...

  • Paradyne 5620 RTU - page 20

    20 W arranty , Sales, and Service Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty , sales, service, repair , installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the fol ...

メーカー Paradyne カテゴリー Network Router

Paradyne 5620 RTUのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 5620 RTUの取扱説明書
- Paradyneの製品カード
- パンフレット
- またはParadyne 5620 RTUの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Paradyne 5620 RTUの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Paradyne 5620 RTUの取り付け説明書、サービスマニュアル、簡易説明書、またはParadyne 5620 RTUのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Paradyne 5620 RTUの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Paradyne 5620 RTUデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがParadyne 5620 RTUを使用するのを助ける技術的文書のことです。説明書は通常、全てのParadyne 5620 RTUユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Paradyneの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Paradyne 5620 RTUの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははParadyne 5620 RTUの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Paradyne 5620 RTUに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Paradyne 5620 RTUデバイスの基本機能を使うにあたってのヒント。 Paradyne 5620 RTUのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Paradyne 5620 RTUに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるParadyne 5620 RTUのメーカー/サービスへの連絡先に関する情報。

Paradyne 5620 RTUについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもParadyne 5620 RTUの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがParadyne 5620 RTUで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)