Bryant 663Cの取扱説明書

12ページ 0.13 mb
ダウンロード

ページに移動 of 12

Summary
  • Bryant 663C - page 1

    NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since the last issue. SAFETY CONSIDERATIONS Improper installation, adjustment, alteration, service, maintenance, or use can cause explosion, fire, electrical shock, or other conditions which may cause death, personal injury, or property dam ...

  • Bryant 663C - page 2

    II. INSTALL ON A SOLID, LEVEL MOUNTING PAD If conditions or local codes require the unit be attached to pad, tie down bolts should be used and fastened through knockouts provided in unit base pan. Refer to unit mounting pattern in Fig. 3 to determine base pan size and knockout hole location. On rooftop applications, mount on level platform or frame ...

  • Bryant 663C - page 3

    VII. CHECK OUTDOOR CHECK-FLO-RATER® PISTON Check outdoor unit piston. Remove retainer on liquid service valve and check piston size with matching number listed on outdoor unit rating plate. VIII. CHECK DEFROST THERMOSTAT Check defrost thermostat to ensure it is properly located and securely attached. There is a liquid header with a brass distribut ...

  • Bryant 663C - page 4

    IMPORTANT: Check to be certain factory tubing on both indoor and outdoor unit has not shifted during shipment. Ensure tubes are not rubbing against each other or any sheet metal. Pay close attention to feeder tubes, making sure wire ties on feeder tubes are secure and tight. X. MAKE ELECTRICAL CONNECTIONS WARNING: To avoid personal injury or death, ...

  • Bryant 663C - page 5

    WARNING: The unit cabinet must have an uninter- rupted or unbroken ground to minimize personal injury if an electrical fault should occur. The ground may consist of electrical wire or metal conduit when installed in accordance with existing electrical codes. Failure to follow this warning can result in an electric shock, fire, or death. B. Connect ...

  • Bryant 663C - page 6

    Fig. 9—Typical 24-v Circuit Connections using Bryant Model HP Thermostat with Fan Coils and No Outdoor Thermostat, 1 Outdoor Thermostat, or 2 Outdoor Thermostats A97400 24 VAC HOT       R G W/W1 Y/Y2 O/W2 R W3 W2 RVS COOLING         C B S1 S2 W2 BRYANT PROGRAMMABLE THERMOSTAT MODEL HP TWO? ...

  • Bryant 663C - page 7

    Fig. 10—Typical 24-v Circuit Connections using Other HP Thermostats with Fan Coils and No Outdoor Thermostat, 1 Outdoor Thermostat, or 2 Outdoor Thermostats A97404 24 VAC HOT       R C W2 Y G R W3 W2 G RVS COOLING         E W2 OTHER HP THERMOSTAT  TWO OUTDOOR THERMOSTATS  FA, FB ...

  • Bryant 663C - page 8

    Fig. 12—Typical 24-v Circuit Connections using Bryant Model 2S Thermostat with FK4C Fan Coil and Smart Staging A97405 24 VAC HOT       R G W/W1 Y/Y2 Y/Y2 Y1/W2 R DH RVS COOLING         C B L S1 S2 Y W2 BRYANT PROGRAMMABLE THERMOSTAT MODEL 2S FK4C FAN COIL HEAT  PUMP   G O O/W ...

  • Bryant 663C - page 9

    Fig. 13—Typical 24-v Circuit Connections using Bryant Model HP Thermostat with Smart Heat and No Outdoor Thermostat, 1 Outdoor Thermostat, or 2 Outdoor Thermostats A97409 24 VAC HOT       R G W/W1 Y/Y2 O/W2 RVS COOLING         C B S1 S2 SUPPLEMENTAL HEATING RELAY BRYANT PROGRAMMABLE THER ...

  • Bryant 663C - page 10

    Fig. 14—Typical 24-v Circuit Connections using Other HP Thermostats with Smart Heat and No Outdoor Thermostat, 1 Outdoor Thermostat, or 2 Outdoor Thermostats A97412 24 VAC HOT       R C Y G O RVS COOLING         W2 OTHER HP THERMOSTAT  HEAT  PUMP   E R C Y G O W2T W3 W2D Y 0 R C ...

  • Bryant 663C - page 11

    providing electrical potential to second heater sequencer (if used). If outdoor temperature falls below setting of outdoor thermostat (field-installed option), contacts close to complete circuit and bring on second bank of supplemental electric heat. When thermostat is satisfied, its contacts open, de-energizing contactor and sequencer. All heaters ...

  • Bryant 663C - page 12

    XIV. CHECK CHARGE Factory charge is shown on unit rating plate. To check charge in cooling mode, refer to Cooling Only Procedure. To check charge in heating mode, refer to Heating Check Chart Procedure. A. Cooling Only Procedure NOTE: If subcooling charging conditions are not favorable, charge must be weighed in accordance with unit rating plate ± ...

メーカー Bryant カテゴリー Heat Pump

Bryant 663Cのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 663Cの取扱説明書
- Bryantの製品カード
- パンフレット
- またはBryant 663Cの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bryant 663Cの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bryant 663Cの取り付け説明書、サービスマニュアル、簡易説明書、またはBryant 663Cのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bryant 663Cの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bryant 663Cデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBryant 663Cを使用するのを助ける技術的文書のことです。説明書は通常、全てのBryant 663Cユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bryantの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bryant 663Cの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBryant 663Cの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bryant 663Cに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bryant 663Cデバイスの基本機能を使うにあたってのヒント。 Bryant 663Cのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bryant 663Cに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBryant 663Cのメーカー/サービスへの連絡先に関する情報。

Bryant 663Cについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBryant 663Cの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBryant 663Cで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)