Makita AN611の取扱説明書

19ページ 1.28 mb
ダウンロード

ページに移動 of 19

Summary
  • Makita AN611 - page 1

    Construction Coil Nailer 4.5 - 8.5 kgf/cmZG (65 - 120 PSIG) MODEL AN61 1 300 - 400 PCS. 32 mm, 38 mm, 45 mm, 50 mm, 57 mm, 65 mm (1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2") INSTRUCTION MANUAL SPECIFICATIONS Air pressure I Applicable length I Nail capacity Min. hose diameter Dimensions (L x W x H) Net weight 6.5 mm (1/ ...

  • Makita AN611 - page 2

    IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING THIS TOOL, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. For personal safety and proper operation and main- tenance of the tool, read this instruction manual carefully before using the tool. *Always wear safe ...

  • Makita AN611 - page 3

    General Tool Handling Guidelines: 1. Always assume that the tool contains fasteners. 2. Do not point the tool toward yourself or anyone whether it contains fasteners or not. 3. Do not actuate the tool unless the tool is placed firmly against the workpiece. 4. Respect the tool as a working implement. 5. No horseplay. 6. Do not hold or carry the tool ...

  • Makita AN611 - page 4

    *Only those involved in the work should be in the vicinity. Children especially must be kept away at all times. There may be local regulations concerning noise which must be complied with by keeping noise levels within prescribed limits. In certain cases, shutters should be used to contain noise. Do not play with the contact element: it prevents ac ...

  • Makita AN611 - page 5

    Never use the tool with other than compressed air. If bottled gas (carbon dioxide, oxgen, nitrogen, hydrogen, air, etc.) or combustible gas (hydrogen, propane, acetylene, etc.) is used as a power source for this tool, the tool will explode and cause serious injury. *Always check the tool for its overall condition and loose screws before operation. ...

  • Makita AN611 - page 6

    Make sure that the trigger is locked when the change lever is set to the LOCK position. Check walls, ceilings, floors, roofing and the like carefully to avoid possible electrical shock, gas leakage, explosions, etc. caused by striking live wires, conduits or gas pipes. Use only nails specified in this manual. The use of any other nails may cause ma ...

  • Makita AN611 - page 7

    Make sure no one is nearby before nailing. Never attempt to nail from both the inside and outside at the same time. Nails may rip through and/or fly off, presenting a grave danger. Watch your footing and maintain four balance with the tool. Make sure there is no one below when working in high locations, and secure the air hose to prevent danger if ...

  • Makita AN611 - page 8

    Do not leave the loaded tool or the air compressor under pressure for a long time out in the sun. Be sure that dust, sand, chips and foreign matter will not enter the tool in the place where you leave it setting. *Do not point the ejection port at anyone in the When the air hose is connected, do not carry the tool with your finger on the trigger or ...

  • Makita AN611 - page 9

    Stop nailing operations immediately if you notice something wrong or out of the ordinary with the tool. .Always disconnect the air hose and remove all of the nails: 1. When unattended. 2. Before performing any maintenance or repair. 3. Before cleaning a jam. 4. Before moving the tool to a new location. Perform cleaning and maintenance right after f ...

  • Makita AN611 - page 10

    .Do not operate this tool if it does not contain a legible WARNING LABEL. Do not modify tool without authorization from Makita. Ask Makita's Factory or Authorized service center for periodical inspection of the tool. To maintain product SAFETY and RELIABILITY, maintenance and repairs should be performed by Makita Authorized or Factory Service ...

  • Makita AN611 - page 11

    TOOL INSTALLATION INSTRUCTIONS AND USE Selecting compressor The air compressor must comply with the requirements of Select a compressor that has ample pressure and air output to assure cost-efficient operation. The graph shows the relation between nailing frequency, applicable pressure and compressor air output. Thus, for example, if nailing takes ...

  • Makita AN611 - page 12

    Nose adapter CAUTION : Always lock the trigger and disconnect the hose before installing or removing the nose adapter. When nailing workpieces with easily-marred surfaces, use the nose adapter. It is factory installed at the rear of the tool. Attach the nose adapter to the contact arm (see right). When not in use, store the nose adapter at the rear ...

  • Makita AN611 - page 13

    Place the nail coil over the coil support plate. Uncoil enough nails to reach the feed claw. Place the first nail in the driver channel and the second nail in the feed claw. The nail heads must be in the slot in the feeder body. Place other uncoiled nails on feeder body. Close the magazine cap and door after checking to see that the nail coil is se ...

  • Makita AN611 - page 14

    For No. 1 method, set the change lever to the “Intermittent Nailing” position. For No. 2 method, set the change lever to the “Continuous Nailing” position. After using the change lever to change the nailing method, always make sure that the change lever is properly set to the position for the desired nailing method. Air exhaust Air exhaust ...

  • Makita AN611 - page 15

    Never hang the tool on a waist belt or the like. Dangerous accidental firing may result. Nails Handle nail coils and their box care.Jlly. If the nail coils have been handled roughly, they may be out of shape or their connector breaks, causing poor nail feed. Avoid storing nails in a very humid or hot place or place exposed to direct sunlight. .. ...

  • Makita AN611 - page 16

    MAINTENANCE CAUTION: Always be sure that the trigger is locked and the air hose is disconnected from the tool before attempting to perform inspection or maintenance. Maintenance of nailer Always check the tool for its overall condition and loose screws before operation. Tighten as required. Make sure all safety systems are in working order before o ...

  • Makita AN611 - page 17

    When the tool is not to be used for an extended period of time, lubricate the tool using pneumatic tool oil and store the tool in a safe place. Avoid exposure to direct sunlight and/or a humid or hot environment. Maintenance of compressor, air set and air hose After operation, always drain the compressor tank and the air filter. If moisture is allo ...

  • Makita AN611 - page 18

    Keep the air hose away from heat (over 6OoC, over 140°F), away from chemicals (thinner, strong acids or alkalis). Also, route the hose away from obstacles which it may become dangerously caught on during operation. Hoses must also be directed away from sharp edges and areas which may lead to damage or abrasion to the hose. To maintain product SAFE ...

  • Makita AN611 - page 19

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one- year period, return the COMPLETE tool, freig ...

メーカー Makita カテゴリー Laptop

Makita AN611のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- AN611の取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita AN611の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita AN611の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita AN611の取り付け説明書、サービスマニュアル、簡易説明書、またはMakita AN611のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita AN611の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita AN611デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita AN611を使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita AN611ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita AN611の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita AN611の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita AN611に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita AN611デバイスの基本機能を使うにあたってのヒント。 Makita AN611のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita AN611に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita AN611のメーカー/サービスへの連絡先に関する情報。

Makita AN611についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita AN611の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita AN611で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)