Omega HHT=1501の取扱説明書

27ページ 1.24 mb
ダウンロード

ページに移動 of 27

Summary
  • Omega HHT=1501 - page 1

    ...

  • Omega HHT=1501 - page 2

    ...

  • Omega HHT=1501 - page 3

    TABLE OF CONTENTS 1. SPECIFICATIONS ...................................................................................... 1 2. PANEL FUNCTIONS ................................................................................... 2 3. OPERATING INSTRUCTION ..................................................................... 4 3.1. Normal Operation . ...

  • Omega HHT=1501 - page 4

    ...

  • Omega HHT=1501 - page 5

    1 1 1. SPECIFICATIONS Speed (Non-contact): Range Resolution Accuracy RPM 10.00 - 99999 0.01/0.1/1 0.04% ±2 dgts rps(Hz) 0.200 - 2000.0 0.001/0.01/0.1 0.04% ±2 dgts Speed (Contact) Range Resolution Accuracy RPM / (/ symoblizes "Contact" 20.00 - 29999 0.01/0.1/1 0.04% ±2 dgts m/min 2.000 - 2999.9 0.001/0.01/0.1 0.04% ±2 dgts ft/min 6.00 ...

  • Omega HHT=1501 - page 6

    2 2 2. PANEL FUNCTIONS ...

  • Omega HHT=1501 - page 7

    3 3 2.1. Reflecting tape Attach a reflecting tape to the surface of the unit to be measured 2.2. Reflecting signal light beam It is recommenced that the reflecting surface is perpendicular to the emitting/receiving unit for best measurement. 2.3. Emitting/Receiving Unit The red light emits from the left side of the tachometer. And a receiving senso ...

  • Omega HHT=1501 - page 8

    4 4 2.10. Start Measurement Symbol 2.11. Hours:Minutes Clock ...

  • Omega HHT=1501 - page 9

    5 5 3. OPERATING INSTRUCTION ...

  • Omega HHT=1501 - page 10

    6 6 3.1. Normal Operation a. Install four 1.5V AA size batteries. b. Cut off a piece of reflective tape of size 1.0 cm x 1.4 cm (optimal size) c. Wipe off oil or stains from the surface where reflective tape will be adhered. d. Stick the self-adhesive re flective tape on the object whose rotational speed is to be measured. The reflective tape shoul ...

  • Omega HHT=1501 - page 11

    7 7 3.2. Using the Mechanical Adaptor (Option RM1502) a. Select proper rubber head. b. Attach the mechanical adaptor to the unit. and fasten the screw. c. Press the unit button (left button) to select RPM / ( instead of RPM only). The auxiliary LED will be turned on while the main LED will be turned off. d. Press against the shaft of the object to ...

  • Omega HHT=1501 - page 12

    8 8 3.3. Measurement of Surface Speed(m/min, ft/min, or yd/min) a. Attach the mechanical adaptor (option RM-1502) to the unit. b. Press the unit button to select desired unit. The auxiliary LED will be turned on while the main LED will be turned off. c. Slightly touch against the surface to be measured. ...

  • Omega HHT=1501 - page 13

    9 9 3.4. Use as an Event Counter with Ext ernal Light Source a. Press the unit button several times to select the unit of "No. O" (counts). The "O" symbol is used to instruct users that external light source is required. b. Wh en the symbol "No. O" appears, the tachometer reset the upper clock to 00:00 and start counti ...

  • Omega HHT=1501 - page 14

    10 10 3.6. External Signal(TTL) Input (RM1501) Instead of receiving signal from light source, users can input external TTL signal (High: > 4.5V, Low: 0V) through pin 8 of RS232C connector with pin 5 as signal ground. NOTE: It is strongly recommended that the emiting/receiving unit be covered to avoid undesired light signal coming in. 3.7. Digita ...

  • Omega HHT=1501 - page 15

    11 11 3.8. Measuring Slow Rotating Objects If the rotati ng speed of the object which you are measuring is very slow, it is recommended that you use a tripod to hold the tachometer in place and use multiple pieces of tape for more accurate result. If multiple pieces of tape are used, each piece of tape should be located at a equal distance to each ...

  • Omega HHT=1501 - page 16

    12 12 seconds, and the max/min/ave symbols will disappear in LCD. 3.10. Turning On/Off Tachometer Press any button will turn on the power of tachometer. To turn off the power of tachometer, press and hold the START button until word "OFF" is displayed in LCD. Then release the START button. 3.11. Disable Auto-Power-Off Function If tachomet ...

  • Omega HHT=1501 - page 17

    13 13 3.12. REPLACING THE BATTERIES a. When the symbol (low battery) appears in the LCD, it is time to replace the batteries. b. Remove the screw of the battery cover and remove the battery cover. c Replace the old batteries with 4 new batteries. Do not mix different type of batteries together. d. Replace the battery cover and fasten the screw. ...

  • Omega HHT=1501 - page 18

    14 14 4. Protocol of RS-232C Serial Interface (RM-1501) Ten bytes are sent out through RS-232C connector to PC. The definitions of each byte are as followings: Byte 1: Leading byte 0x0D Byte 2: Decimal point of LCD display bit0: dp1 (0000.0), if 1 bit1: dp2 (000.00), if 1 bit2: dp3 (00.000), if 1 Byte 3: Flags for current status bit0: low battery, ...

  • Omega HHT=1501 - page 19

    15 15 5. Installation of Window TM Application Software (RM-1501) 5.1. For Windows 3.1 A. Start Microsoft TM Windows TM B. Insert disk in drive A (or B) C. From Program Manager , select File menu and choose Run D. Type a:setup (or b:setup) and press Enter key 5.2. For Windows 95 A. Start Windows TM 95 B. Insert disk in drive A (or B) C. Press STA ...

  • Omega HHT=1501 - page 20

    16 16 6. Description of Windows TM Application Program (RM-1501) Main Window : When the program is executed, the program automatically search for connected tachometer or available serial port. If no serial port is available, then a message of "No communication port" will be displayed, and the program exits . Once communication port is set ...

  • Omega HHT=1501 - page 21

    17 17 VIEW FILE : If the View option under FILE in the Main Window is selected, a view window will be shown as above, and the users can review your ASCII data file. If a printer is connected to the PC, users can print out content selectively. File: Open users data file by selecting this menu. Users will be asked to enter file name. After the name b ...

  • Omega HHT=1501 - page 22

    18 18 Selected: Indicate the current record number being selected. DISPLAY : DISPLAY menu has four options: DIGITAL, ANALOG, LIST, and GRAPHIC. DIGITAL: If this option is selected or CTRL+D is pressed, a window, which emulates multimeter's LCD display, shall appears on the screen. ANALOG: ...

  • Omega HHT=1501 - page 23

    19 19 If this option is selected or CTRL+A is pressed, a window, which emulates an analog meter, shall appear on the screen. LIST: If this option is selected or CTRL+L is pressed, a window, which lists the date, function, range, and value every sampling, shall appear on the screen. GRAPHIC: If this option is selected or CTRL+G is pressed, a window, ...

  • Omega HHT=1501 - page 24

    20 20 the minimum and maximum value for the Y (vertical) axis. Option : If you select Option, a pull down menu will show three options: Sample Rate, Baud Rate. Upper Limit: Enter upper limit. If upper limit is exceeded, a OVER message will be displayed in screen. Lower Limit: Enter lower limit. If displayed value is less than lower limit, a UNDER m ...

  • Omega HHT=1501 - page 25

    21 21 ...

  • Omega HHT=1501 - page 26

    22 22 ...

  • Omega HHT=1501 - page 27

    23 23 ...

メーカー Omega カテゴリー Automobile Parts

Omega HHT=1501のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HHT=1501の取扱説明書
- Omegaの製品カード
- パンフレット
- またはOmega HHT=1501の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Omega HHT=1501の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Omega HHT=1501の取り付け説明書、サービスマニュアル、簡易説明書、またはOmega HHT=1501のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Omega HHT=1501の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Omega HHT=1501デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがOmega HHT=1501を使用するのを助ける技術的文書のことです。説明書は通常、全てのOmega HHT=1501ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Omegaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Omega HHT=1501の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははOmega HHT=1501の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Omega HHT=1501に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Omega HHT=1501デバイスの基本機能を使うにあたってのヒント。 Omega HHT=1501のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Omega HHT=1501に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるOmega HHT=1501のメーカー/サービスへの連絡先に関する情報。

Omega HHT=1501についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもOmega HHT=1501の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがOmega HHT=1501で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)