Pelco MC5700-3の取扱説明書

12ページ 0.17 mb
ダウンロード

ページに移動 of 12

Summary
  • Pelco MC5700-3 - page 1

    MC5700 Series 1/3-Inch Monochr ome Camera Installation/ Operation Manual C1903M (4/99) Pelco • 3 5 00 Pelco Way • Clovis , CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120 ...

  • Pelco MC5700-3 - page 2

    2 Pelco Manual C1903M (4/99) IMPOR T ANT SAFEGUARDS AND W ARNINGS 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. T o pre v ent fire or shock hazard, do not e xpose the unit to rain or moisture . CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. The product and/or manual may bear the f ...

  • Pelco MC5700-3 - page 3

    Pelco Manual C1903M (4/99) 3 LOCA TION AND FUNCTION OF P ARTS Refer to Illustration B for the location of the camera parts listed below . NOTE: References to illus- trations in this manual are keyed to the illustrations in the manual that is supplied with the camera. B T ripod adapter (may be attached to top or bottom of camera) Camera mounting rec ...

  • Pelco MC5700-3 - page 4

    4 Pelco Manual C1903M (4/99) Be sure to attach the lens mount cap when the lens is not mounted. When using an auto-iris lens, use only a DC-driven type or a direct current drive coil with a resistance value over 150 ohms. When using an auto-iris lens, attach it as follows. For a manual lens, omit step 3. Refer to Illustration E. 1. Unscrew the lens ...

  • Pelco MC5700-3 - page 5

    Pelco Manual C1903M (4/99) 5 E A C CS 2 1 4 3 CCD-IRIS ON OFF Lens Installation CCD-Iris Function ...

  • Pelco MC5700-3 - page 6

    6 Pelco Manual C1903M (4/99) NOT A V AILABLE ON 5700 SERIES Incident Light LENS CAMERA (STYLIZED) Iris opening (sometimes referred to as aperture) is defined by f/stop numbers. The higher the number the more closed the iris is. IRIS CCD IMAGER CCD Iris (Electronic Shutter) CCD out- put voltage is electronically sampled and used to adjust for small ...

  • Pelco MC5700-3 - page 7

    Pelco Manual C1903M (4/99) 7 Information Box Information Box LENS TYPE MANUAL IRIS V ARIABLE LIGHT CONDITIONS ST A TIC LIGHT CONDITIONS AUT O IRIS • Turn Manual Iris ring so iris is fully open and set the Focus ring for ∞ (or distant object). • Adjust Backfocus with CCD IRIS switch initially set to the OFF position. • Use the C/CS adjust- m ...

  • Pelco MC5700-3 - page 8

    8 Pelco Manual C1903M (4/99) Information Box Information Box The purpose of backfocusing is to make the adjustments necessary for the picture to remain in focus throughout the camera’s zoom range, which is the case for instance, in motorized zoom, auto iris configurations. Manual Iris lens/camera combinations also need to be backfocused. Follow t ...

  • Pelco MC5700-3 - page 9

    Pelco Manual C1903M (4/99) 9 CAMERA Install the camera where it will not be affected by fluorescent lights or window reflections. If the camera is used under illumination that is not steady , the picture may flicker . The MC5700-2 must be operated with a 24 V AC, 60 Hz, Class 2 power supply. The MC5700-2X must be operated with a 24 V AC, 50 Hz powe ...

  • Pelco MC5700-3 - page 10

    10 Pelco Manual C1903M (4/99) V -PHASE ADJUSTMENT V ertical phase adjustment is required only if your system uses two or more cameras. The vertical phase can be manually adjusted within the range of approximately -90 degrees to +90 degrees (refer to Illustration H). I V ertical Phase H AC Line Lock Adjustment V ertical phase adjustment is not verti ...

  • Pelco MC5700-3 - page 11

    Pelco Manual C1903M (4/99) 11 INCIDENT LIGHT LEVEL ADJUSTMENT Since the incident light level has been preset at the factory , usually no further adjustment is required. If the picture is too dark, however , or if the picture’s highlights are extremely overexposed, adjust the LEVEL adjustment screw . This adjustment can only be used for auto-iris ...

  • Pelco MC5700-3 - page 12

    12 Pelco Manual C1903M (4/99) REVISION HISTOR Y Manual # Date Comments C1903M 1 1/96 Original version. 4/99 Added MC5700-2X model. Revised manual to new format. ® Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved. Power Consumption MC5700-2: Approximately 4.5 W MC5700-2X: Approximately 4.5 W ...

メーカー Pelco カテゴリー Security Camera

Pelco MC5700-3のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- MC5700-3の取扱説明書
- Pelcoの製品カード
- パンフレット
- またはPelco MC5700-3の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Pelco MC5700-3の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Pelco MC5700-3の取り付け説明書、サービスマニュアル、簡易説明書、またはPelco MC5700-3のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Pelco MC5700-3の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Pelco MC5700-3デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPelco MC5700-3を使用するのを助ける技術的文書のことです。説明書は通常、全てのPelco MC5700-3ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Pelcoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Pelco MC5700-3の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPelco MC5700-3の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Pelco MC5700-3に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Pelco MC5700-3デバイスの基本機能を使うにあたってのヒント。 Pelco MC5700-3のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Pelco MC5700-3に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPelco MC5700-3のメーカー/サービスへの連絡先に関する情報。

Pelco MC5700-3についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPelco MC5700-3の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPelco MC5700-3で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)