日本語 dropdown-ico

Graco PRO 309292Sの取扱説明書

48ページ 1.55 mb
ダウンロード

ページに移動 of 48

Summary
  • Graco PRO 309292S - page 1

    Instr uctions Manual Electr ostatic PR O ™ Xs3 and PR O ™ Xs4 Air Spra y Guns For use in Class I, Div . I hazardous locations using Gr oup D spray materials. For use in Group II, Zone 1 areas using Gr oup IIA spray materials. For Pr ofessional Use ONL Y . 100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure 100 psi (0.7 MPa, 7 bar) Maximum W or ...

  • Graco PRO 309292S - page 2

    2 309292S T ab le of Contents List of Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 W ar ning Sym bol . . . . . . . . . . . . . . . . . . . . . . . . . 4 Caution Symb ol . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Introduction . . . . . . . ...

  • Graco PRO 309292S - page 3

    List of Models 309292S 3 List of Models Par t N o . Mo d e l Smart Display T ype of Coat ings Operation Manual Standard High Conductivity 244400, Series D PRO Xs3 X 309294/3W9294/ 3Z9294 244579, Series D PRO Xs3 (1.5 mm nozzle) XX 309294/3W9294/ 3Z9294 24A511, Series B PRO Xs3 (1.2 mm nozzle) 244575, Series D PRO Xs3 X 309294/3W9294/ 3Z9294 244576, ...

  • Graco PRO 309292S - page 4

    Warnings 4 309292S Wa r n i n g s W arning Symbol This symbol aler ts you to t he possibility of serious injur y or death if y ou do not f ollow the instructions. Caution Symbol This symbol aler ts you to t he possibility of damage to or destruction of equipment if y ou do not f ollow the instruc- tions. WARNING CAUTION WA R N I N G Fire, Explosion ...

  • Graco PRO 309292S - page 5

    Warnings 309292S 5 W ARNING Equipment Misuse Hazar d Equipment misu se can cause the equipment to rupture , malfunction, or start unexp ectedly and result in a serious injur y . • This equipment is f or prof essional use only . • Read all man uals, tags , and labels bef ore oper ating the equipme nt. • Use the equipment only f or its intende ...

  • Graco PRO 309292S - page 6

    Introduction 6 309292S Intr oduction How the Electr ostatic Air Spra y Gun W orks The air hose supplies air to the spr ay gun. P ar t of the air operat es the turbine and the rest of the air atomiz es the fluid being sp ray ed. The turbine generates po wer , which is conv er ted by t he power car tridge to supply high v olt- age current to t he gun ...

  • Graco PRO 309292S - page 7

    Installation 309292S 7 Installation Install the System F IG . 2. shows a typical e lectrostatic air spra y sys tem. It is not an actual system des ign. F or assistance in designing a system to suit y our par ticular needs, contact yo ur Graco distributor . W arning Sign Mount warning signs in the spr ay area whe re they can easily be seen and read ...

  • Graco PRO 309292S - page 8

    Installation 8 309292S Fig. 2. Typica l Installation Key I O ES ti1498a A B* C* D *E F G H J* K L M N O P Q* *R S T U* V W C G ES ON/OFF valv e: I is ON, 0 is OFF The air supply to the gun must be electri- cally interlocked with the ventilators to pre- vent the power supply from operating without ventilating fans on. Non-Hazardou s Area Hazardous A ...

  • Graco PRO 309292S - page 9

    Installation 309292S 9 Connect the Air Line 1. Connect the Graco G rounded Air Supply Hose (R) between th e air supply line and the gun's air inlet (V). The gun air inlet fit ting has a left-hand thread. Connect th e air supply ho se ground wire (Q) to a true ear th ground. 2. Install an air line filter/w ater separator (O) on the gun air line ...

  • Graco PRO 309292S - page 10

    Installation 10 309292S Select a Fluid Nozzle and Air Cap The gun is supplied with P ar t No . 197266 Nozzle and 24A376 Air Cap. If you require a different size, ref er t o T able 1 and T able 2 , and instruction manual 30941 9, or consult with your Graco distributor . See Air Cap/Nozz le Replacement on page 26. A wide pattern kit (P/N 24A43 1) is ...

  • Graco PRO 309292S - page 11

    Installation 309292S 11 4. Remov e the fluid tube and fittings . 5. Remov e the fluid inlet br ack et. 6. Install the ne w brack et (3) from the kit loosely . See F IG . 3. 7. Place the spacer (5) in the barrel inlet. Ap ply Graco dielectric grease (4) to the o-rings (2a, 2b) and to both threads of the fluid fitting (2). Thread the fitt ing into th ...

  • Graco PRO 309292S - page 12

    Installation 12 309292S Gr ounding The follo wing are minimum groundin g requiremen ts for a basic elect rostatic syste m. Y our system ma y include other equipment or objects which m ust be grounded. Check yo u r local electr ical code f or de tailed grounding instru ctions. Y our system must be connected to a true ear th ground . • Pump: ground ...

  • Graco PRO 309292S - page 13

    Installation 309292S 13 Chec k Electrical Grounding 1. Hav e a q ualified electr ician ch eck the electrical groundin g continuity of t he spra y gun and air hose . 2. T urn the ES ON/O FF v a lv e OFF . 3. T ur n off the air and fluid supp ly to the gun. The f luid hose must not have any fluid in it. 4. Mak e sure the grounded a ir hose (R) is con ...

  • Graco PRO 309292S - page 14

    Installation 14 309292S Chec k Fluid Resistivity Graco P ar t No . 722886 Resistance Meter and 72 2860 Probe are a vaila ble as accessories to chec k that the resistivity of the fluid b eing spray ed meets the require- ments of an electrostatic air spr ay system. F ollow the instr uctions in cluded with the meter and probe . Readings of 25 megohms- ...

  • Graco PRO 309292S - page 15

    Operation 309292S 15 Operation Lo w V oltage Adjustment (Smar t Guns Onl y ) The ES HI/LO s witch enables y ou to s witch between full v oltage and a lower v oltage output. The low er voltage is f actor y set, but can be adjusted. 1. Set the ES HI/LO switch to LO . 2. Remove the LO V OL T AGE adjustment plug (53) . Set the desired voltage, using a ...

  • Graco PRO 309292S - page 16

    Maintenance 16 309292S Maintenance Flush the Spra y Gun Flush the gun bef ore changing co lors, at the end of t he da y , bef ore storing, and befo re repair ing the gun. 1. T ur n th e ES ON/OFF valv e OFF . 2. Relie ve the pr essure. 3. Change the f luid source to solv ent, or disconnect the fluid line and connect a solv ent supply line to the gu ...

  • Graco PRO 309292S - page 17

    Maintenance 309292S 17 7. Hang the gun from it s hook, with the nozzle pointing down. 8. When ready to spra y again, reconnect th e fluid sup- ply line. F ollow the Se tup procedure in the Opera - tion Man ual. ti1288a ...

  • Graco PRO 309292S - page 18

    Electrical Tests 18 309292S Electrical T ests Electrical components inside the gun affect p erformance and safety . The f o llowing procedures test the condition of the pow er supply (18) and electrode (29), and electr i- cal continuity bet ween components . Use megohmmeter P ar t No . 241079 (AA) and an applied v oltage of 500 V . Connect the lead ...

  • Graco PRO 309292S - page 19

    Electrical Tests 309292S 19 T est P o wer Supply Resistance 1. Remov e the po wer supply (18), page 30. 2. Remov e the turbine alt er nator (19) from t he power supply , page 31. 3. Measure resistance from the power su pply's ground strips (EE) to the spring (18b). See F IG . 7. 4. The resist ance should be 95-105 megohms f or the PRO Xs3, and ...

  • Graco PRO 309292S - page 20

    Electrical Tests 20 309292S T est Electr ode Resistance 1. Inser t a conductiv e rod (B) into the gun barr el (remo ved f or the pow er supply test) and against th e metal conta ct (C) in the front of the barrel. 2. Measure the resist ance between the conductiv e rod (B) and the el ectrode (29). The resistance should be 20-30 megoh ms. See F IG . 8 ...

  • Graco PRO 309292S - page 21

    Troubleshooting 309292S 21 T r oub leshooting Chec k all possible remedies in the T roub leshooting Char t bef ore disassemb ling the gun. Spra y P attern T roub leshooting Some spra y pattern problems ar e caused by the improp er balance between air and flu id. WA R N I N G Electric Shoc k Hazard Installing and ser vic ing this equipment requires ...

  • Graco PRO 309292S - page 22

    Troubleshooting 22 309292S Gun Operation T roub leshooting Problem Cause Solution Excessive spr ay f og. Atomizing air pressure too high. Close restr ictor valv e some, or decrease air p ressure as low as pos- sible; minimum 40 psi (0.28 MP a, 2.8 bar) needed at gun f or full v oltage. Fluid too thin. Increase viscosity . “Orange P eel” finish. ...

  • Graco PRO 309292S - page 23

    Troubleshooting 309292S 23 Electrical T roub leshooting * ES indicator light is off when the gun is tr iggered. Prob lem Cause Solution P oor wrap . ES ON/OFF v alve OFF (0).* T ur n ON (I). Gun air pressu re too low . Chec k air pressure to gun; minim um 40 psi (0.28 MP a, 2.8 bar) ne eded at gun f or full voltag e. Atomizing air pressure too hig ...

  • Graco PRO 309292S - page 24

    Repair 24 309292S Repair Pressure Relief Pr ocedure 1. T urn the ES ON/O FF v a lv e OFF . 2. T ur n off the air b leed valv es to the fluid sour ce and to the gun. 3. T r igger the gun int o a grounded metal waste con- tainer to r elie ve the fluid pr essure. 4. Open the pu mp drain valv e, having a w ast e con- tainer ready t o catch the drainage ...

  • Graco PRO 309292S - page 25

    Repair 309292S 25 Prepare the Gun f or Ser vice • Check all possib le remedies in T roubles hooting bef ore disassemb ling the gun. • Use a vise with padded ja ws to prev ent damage to plastic par ts. • Lubricate the pow er supply o-ring (18a), some pa ck- ing rod par ts (26), and cer ta in fluid fittings wit h dielectric grease (40) , as spe ...

  • Graco PRO 309292S - page 26

    Repair 26 309292S Air Cap/Nozzle Replacement 1. Prepare gun f or service, page 25 . 2. Remove the retaining r ing (27) and air cap (9). See F IG . 11.. 3. P oint gun up and sq ueeze trigger while removin g the fluid nozzle (7) assembly with the m ulti-tool (37). Fig. 11. Air Cap/ Nozzle Replac ement Use non-silicone grease, P ar t No. 111265, on th ...

  • Graco PRO 309292S - page 27

    Repair 309292S 27 Electr ode Replacement 1. Prepar e the gun for service, page 25. 2. Remov e the air cap and nozzle , page 26. 3. Unscrew the electrode (29) with the multi-to ol (37). Hold the packing rod end (26h) to pre vent it from tur ning, F IG . 12. 4. Apply low-strength (pur ple) Loctite ® or eq uivalent thread sealan t to the electrode an ...

  • Graco PRO 309292S - page 28

    Repair 28 309292S Fluid P ac king Remov al 1. Prepare the gun f or ser vice, pa ge 25. 2. Remov e the air cap and fluid nozzl e, page 26. 3. Remove the electrode, page 27. 4. Loosen the trigger scre ws (8) and trigger (30). See F IG . 13.. 5. Remove the packing rod (26), using the multi-tool (37). 6. Chec k all par ts for w ear or damage and replac ...

  • Graco PRO 309292S - page 29

    Repair 309292S 29 P ac king Rod Repair Y ou may r eplace the packing rod as individ ual par ts or as an assemb ly . The assemb ly is pre-adjusted at the f actor y . Bef ore installing the fluid pack ing rod into the gun barrel, mak e sure the inter nal surf aces of the barrel are clean. Remov e any residue with a soft brush or cloth. Check the insi ...

  • Graco PRO 309292S - page 30

    Repair 30 309292S Barrel Remo val 1. Prepare the gun f or ser vice, pa ge 25. 2. Carefu lly loosen the nut (3 2 or 50d) from the brack e t fluid fitti ng (13). Pull the tube (14 or 50a) ou t of the fitting. Mak e sure both f errules and the nut stay with the tube. 3. Loosen the thre e screws (11). 4. Hold the gun handle (17) with one hand and pull ...

  • Graco PRO 309292S - page 31

    Repair 309292S 31 P o wer Supply Remo v al and Replacement • Inspect the gun ha ndle power supply ca vity f or dir t or moisture. Clean wit h a clean, dr y rag. • Do not e xpose gask et (10) to solvents . 1. Prepare gun f or service, page 25. 2. Remov e the barrel (1 6), page 30. 3. Grasp the po wer supply (18) with your hand. With a gentle sid ...

  • Graco PRO 309292S - page 32

    Repair 32 309292S T urbine Alternator Remo va l and Replacement Replace turbine alte r nator bearings after 2000 hours of operat ion. Order P ar t No. 22 3688 Bearing Kit. 1. Prepare gun f or service, page 25 . 2. Remov e the power supply/alter nator assembly , page 31. 3. Disconnect the alte r nator from the po wer supply , page 31. 4. Measure res ...

  • Graco PRO 309292S - page 33

    Repair 309292S 33 F an Air Adjustment V alve Repair 1. Prepar e the gun for service, page 25. 2. Place a wrench on the flats of th e valv e assembly (20) and unscre w it from the handle (17). Y ou may r eplace the valv e as an asse mbly (go to step 9) or as individual parts (steps 3-9). 3. Remove the retaining r ing (20a). See F IG . 19.. 4. T urn ...

  • Graco PRO 309292S - page 34

    Repair 34 309292S Fluid Adjustment V alve Repair 1. Prepare the gun f or ser vice, pa ge 25. 2. Remove the fluid adjust ment valv e (25). It can only be replaced as a complete assembly . See F IG . 20.. 3. Screw t he valv e (25) into t he gun handle. T orque to 15-25 in-lb (1 .7-2.8 N•m). Fig. 20. Fluid Adjustment Valve Air V alve Repair 1. Prepa ...

  • Graco PRO 309292S - page 35

    Repair 309292S 35 Atomizing Air Restrictor V alve Remo val and Replacement 1. Prepar e the gun for service, page 25. 2. Remove the atomizing air restr ictor valv e (23). Inspect the o-ring (23c*). Rep lace if necessar y . See F IG . 22.. 3. Install a new atomizing air restr ictor valv e (23) , or disassemb le and replace par ts individually . The v ...

  • Graco PRO 309292S - page 36

    Parts 36 309292S Pa r t s P ar t No. 244400 60 kV Electr ostatic Gun, Series C (items 1-48, 55 ) P ar t No. 244575 60 kV Electr ostatic Gun, Series C (items 4-30, 35 -55) P ar t No. 244401 85 kV Electr ostatic Gun, Series C (items 1-48, 55 ) 27 9 7 26 16 11 18 19 *10 17 28 20 22 25 15 21*** 23b 35 13 24 38 8 *6 ti1266a I O ES 7a 7b 11 *18a 18b 23a ...

  • Graco PRO 309292S - page 37

    Parts 309292S 37 ti1601a Ref. No. 26: P acking Rod 26a** 26b** 26c** 26d** 26e 26f 26g** 26h TI1488A ti1492a TI491A TI1490A TI1487A TI1481a 31** 32 14 1 5** 22a* 22b* 22c 22d 22e 22f 22g 20a 20b* 20c 20d 19a* 19b 19b 19c 50a 50b 50c 50d 50e 50f 49 49a 49b 50d 50c 50b 5 5** 1 14 **31 32 Ref. No. 22: ES ON/OFF V alve Ref. No. 20: Fan Adjustment V alv ...

  • Graco PRO 309292S - page 38

    Parts 38 309292S P ar t No. 244400 60 kV Electr ostatic Gun, Series C (items 1-48, 55 ) P ar t No. 244575 60 kV Electr ostatic Gun, Series C (items 4-30, 35 -55) P ar t No. 244401 85 kV Electr ostatic Gun, Series C (items 1-48, 55 ) Ref. No. P ar t No. Description Qty 1 110078 FITTING, tube, fluid; used on 244400 1 198587 FITTING, tu be, fluid; use ...

  • Graco PRO 309292S - page 39

    Parts 309292S 39 * Included in Air Seal Repair Kit 244781. ** Included in Fluid Seal Repair Kit 244 911. *** Rubber seal is no t remov able. **** Optional repla cement Electrode Needle 277007 is av ailable f or ab rasiv e mater ials. ▲ Replacement Warning lab els, signs, tags , and ca rds are a vailab le at no cost. 23 244559 V AL VE, air , atomi ...

  • Graco PRO 309292S - page 40

    Parts 40 309292S P ar t Nos. 244579 and 24A511 60 kV Electr ostatic Gun, Series C (it ems 1-48, 51-59) P ar t No. 244576 60 kV Electr ostatic Gun, Series C (items 1-30, 35 -59) P ar t No. 244580 85 kV Electr ostatic Gun, Series C (items 1-48, 51 -59) ti1253a 100 % KV μα 0 HI LO ES I O I O ES 27 9 7 26 16 11 18 19 17 28 20 25 15 21*** 23b 35 13 24 ...

  • Graco PRO 309292S - page 41

    Parts 309292S 41 ti1601a Ref. No. 26: P acking Rod ti1492a TI491A TI1490A 31** 32 14 1 5** 50a 50b 50c 50d 50e 50f 49 49a 49b 50d 50c 50b 5 5** 1 14 **31 32 Fluid T ube: Model 244579 Fluid T ube: Model 244576 Fluid T ube: Model 244580 TI1487A 20a 20b* 20c 20d Ref. No. 20: Fan Adjustment V alve TI1481a 19a* 19b 19b 19c Ref . No . 19: Alter nator 19d ...

  • Graco PRO 309292S - page 42

    Parts 42 309292S P ar t No. 244579 and 24A511 60 kV Electr ostatic Gun, Series C (items 1- 48, 51-59) P ar t No. 244576 60 kV Electr ostatic Gun, Series C (items 1-30, 35 -59) P ar t No. 244580 85 kV Electr ostatic Gun, Series C (items 1-48, 51 -59) Ref. No. Pa r t No. Description Qty 1 110078 FITTING, tub e, fluid; used on 244579 1 198587 FITTING, ...

  • Graco PRO 309292S - page 43

    Parts 309292S 43 * Included in Air Seal Repair Kit 244781. ** Included in Fluid Seal Repair Kit 244 911. *** Rubber seal is no t remov able. **** Optional repla cement Electrode Needle 277007 is av ailable f or ab rasiv e mater ials. ▲ Replacement Warning lab els, signs, tags , and ca rds are a vailab le at no cost. 26d** 178763 . P A CKING, rod; ...

  • Graco PRO 309292S - page 44

    Accessories 44 309292S Accessories Air Line Accessories AirFlex ™ Flex ible Grounded Air Hose 100 psi (7 bar , 0.7 MP a) Maxim um Working Pressure 0.315 in. (8 mm) ID; 1/4 npsm(f ) x 1/4 npsm(f) left-hand thread 244963 6 ft (1.8 m) 244964 15 ft (4.6 m) 244965 25 ft (7.6 m) 244966 36 ft (1 1 m) 244967 50 ft (1 5 m) 244968 75 ft (2 3 m) 244969 100 ...

  • Graco PRO 309292S - page 45

    Accessories 309292S 45 Gun Accessories Gun Repair Kits 244781 Air Seal Repair Kit 244911 Fluid Seal Repair Kit Round P attern Kits Consists of flu id tip , diffuser and a ir cap . 245217 4-6 in. (1 02-152 mm) diameter 245219 8-10 in. (203-254 mm) diamet er Adjustable Round P attern Kit 277851 Slo w velocity , bell shaped spra y pattern for e xcelle ...

  • Graco PRO 309292S - page 46

    Technica l Data 46 309292S T echnical Data Loctite ® is a registere d trademark of th e Loctite Cor poration. Category Data Maximum W orking Fluid Pressure 100 psi (0.7 MP a, 7 bar) Maximum W orking Air Pressure 100 psi (0.7 MPa, 7 b ar) Minimum Air Press ure at Gun In let 40 p si (0.28 MPa, 2.8 bar) Maximum Fluid Operatin g T empe rature 120 ° F ...

  • Graco PRO 309292S - page 47

    Technical Data 309292S 47 ...

  • Graco PRO 309292S - page 48

    All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. Original instructions. T his manual contains English. MM 309292 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Kore ...

メーカー Graco カテゴリー Paint Sprayer

Graco PRO 309292Sのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PRO 309292Sの取扱説明書
- Gracoの製品カード
- パンフレット
- またはGraco PRO 309292Sの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Graco PRO 309292Sの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Graco PRO 309292Sの取り付け説明書、サービスマニュアル、簡易説明書、またはGraco PRO 309292Sのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Graco PRO 309292Sの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Graco PRO 309292Sデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGraco PRO 309292Sを使用するのを助ける技術的文書のことです。説明書は通常、全てのGraco PRO 309292Sユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Gracoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Graco PRO 309292Sの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGraco PRO 309292Sの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Graco PRO 309292Sに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Graco PRO 309292Sデバイスの基本機能を使うにあたってのヒント。 Graco PRO 309292Sのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Graco PRO 309292Sに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGraco PRO 309292Sのメーカー/サービスへの連絡先に関する情報。

Graco PRO 309292Sについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもGraco PRO 309292Sの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGraco PRO 309292Sで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)