日本語 dropdown-ico

Remington Power Tools 100271-01の取扱説明書

16ページ 0.5 mb
ダウンロード

ページに移動 of 16

Summary
  • Remington Power Tools 100271-01 - page 1

    ELECTRIC CHAIN S A W SECTION PAGE Symbol Information ............................................................ 2 Safety Warnings ................................................................. 3 Before Operating Chain Saw ....................................... 3 Kickback ...................................................................... 3 ...

  • Remington Power Tools 100271-01 - page 2

    2 100273 INFORMA TION SYMBOLS ! WARNING ICON G 001 Read Instruction Manual Do Not Expose to Rain or Use in Wet Conditions Remove Plug Immediately if Cable is Damaged or Cut Hold Chain Saw with Both Hands Beware of Kickback Hearing and Eye Protection Must Be Worn Safety Information Warnings Appears Throughout This Manual Pay close attention to them. ...

  • Remington Power Tools 100271-01 - page 3

    3 3 100273 BEFORE OPERATING CHAIN SAW 1. Read and understand this owner ’ s manual before operating chain saw. 2. Use chain saw for cutting wood only. Do not use for cutting any non-wood items. 3. Only well-instructed adults should operate chain saw. Never allow children to operate chain saw. First-time user should obtain informed, practical inst ...

  • Remington Power Tools 100271-01 - page 4

    4 100273 • Never try cutting through two logs at same time. Only cut one log at a time. • Do not bury guide bar nose or try plunge cut (boring into wood using guide bar nose). • Watch for shifting of wood or other forces that may pinch chain. • Use extreme caution when re-entering a previous cut. • Use low-kickback chain and guide bar sup ...

  • Remington Power Tools 100271-01 - page 5

    5 5 100273 Front Hand Guard Shield between front handle and guide bar. Protects left hand while using saw. When kickback occurs, the front hand guard is moved forward by the back of operator ’ s left hand. This stops the saw chain quickly, reducing the chance of serious injury. Front Handle Located at front of saw body. Guide Bar Metal bar that e ...

  • Remington Power Tools 100271-01 - page 6

    6 100273 ! WARNING ICON G 001 W ARNING Cutting edges on chain are sharp. Use protective gloves when handling chain. Figure 3 - Assembling Guide Bar, Chain, and Hand Guard Adjusting Block Adjusting Screw Sprocket Support Adjusting Plate Figure 4 - Part Locations for Assembling Guide Bar ASSEMBL Y UNP ACKING 1. Remove all items from carton. 2. Check ...

  • Remington Power Tools 100271-01 - page 7

    7 7 100273 SAW CHAIN TENSION ADJUSTMENT Note: For pre assembled models, the saw chain tension is properly set at factory. A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Follow steps below to readjust saw chain tension. 1. Before adjusting chain, make sure guide bar nuts are only fi nger ti ...

  • Remington Power Tools 100271-01 - page 8

    8 100273 EXTENSION CORDS Use proper extension cord with this chain saw. Use a HO7RN extension cord no less than 1.5 mm 2 at distances up to 30 meters. Use a ground fault circuit interrupter as part of the power supply system. Use an extension cord heavy enough to carry the current your saw will draw. An undersized cord will cause a voltage drop at ...

  • Remington Power Tools 100271-01 - page 9

    9 9 100273 OPERA TING CHAIN SA W Continued TRIMMING A TREE (Pruning) Trimming a tree is the process of cutting limbs from a living tree. Make sure your footing is fi rm. Keep feet apart. Divide your weight evenly on both feet. Follow directions below to trim a tree. 1. Make fi rst cut 15 centimeters from tree trunk on underside of limb. Use top o ...

  • Remington Power Tools 100271-01 - page 10

    10 100273 OPERA TING CHAIN SA W Continued Figure 14 - Limbing A Tree Limbing is removing branches from a fallen tree. Make sure your footing is fi rm. Keep feet apart. Divide your weight evenly on both feet. Do not remove larger limbs under tree that support log off ground. Remove each limb with one cut (see Figure 14). Clear cut limbs from work a ...

  • Remington Power Tools 100271-01 - page 11

    11 11 100273 OPERA TING CHAIN SA W Continued 2nd Cut 1st Cut Figure 16 - Bucking Log When Log Is Supported On One End 1st Cut 2nd Cut Figure 17 - Bucking Log When Log Is Supported On Both Ends Log Supported On One End 1. Make fi rst cut on underside of log (see Figure 16). Use top of guide bar to make this cut. Cut 1/3 through diameter of log. Thi ...

  • Remington Power Tools 100271-01 - page 12

    12 100273 CLEANING SAW BODY Keep saw body clean. Use a soft cloth dampened with a mild soap and water mixture. Wipe saw body to clean. CARE OF GUIDE BAR Uneven bar wear causes most guide bar problems. Incorrect sharpening of chain cutter and depth gauge settings often cause this. When bar wears unevenly, it widens guide bar groove (see Figure 18). ...

  • Remington Power Tools 100271-01 - page 13

    13 13 100273 CLEANING AND MAINTENANCE Continued Sharpening Cutters Use fi le guide for 30 ° fi ling. 1. Adjust chain for proper tension (see Saw Chain Tension Adjustment , page 7). 2. Clamp guide bar in vise to hold saw steady. Note: Do not clamp chain. 3. Press four millimeter round fi le (attached to fi le guide) into groove between top plat ...

  • Remington Power Tools 100271-01 - page 14

    14 100273 CLEANING AND MAINTENANCE Continued Replacing Saw Chain Replace chain when cutters are too worn to sharpen or when chain breaks. Only use replacement chain noted in this manual. Always include new drive sprocket when replacing chain. This will maintain proper driving of chain. Note: For proper chain and drive sprocket, see Replacement Part ...

  • Remington Power Tools 100271-01 - page 15

    15 15 100273 TROUBLESHOOTING OBSERVED FAULT Saw runs, but does not cut. Saw does not cut unless heavily forced. Cutting produces only sawdust with few large chips. Saw runs slow. Saw stalls easily. Motor of saw does not run when you squeeze trigger. Motor of saw runs, but chain does not move. Chain does not get oil. Chain comes off guide bar. Saw s ...

  • Remington Power Tools 100271-01 - page 16

    W ARRANTY INFORMA TION KEEP THIS WARRANTY Always specify model and serial numbers when writing the factory. We reserve the right to amend these speci fi cations at any time without notice. The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied. This product is warranted to be free from defect ...

メーカー Remington Power Tools カテゴリー Chainsaw

Remington Power Tools 100271-01のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 100271-01の取扱説明書
- Remington Power Toolsの製品カード
- パンフレット
- またはRemington Power Tools 100271-01の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Remington Power Tools 100271-01の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Remington Power Tools 100271-01の取り付け説明書、サービスマニュアル、簡易説明書、またはRemington Power Tools 100271-01のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Remington Power Tools 100271-01の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Remington Power Tools 100271-01デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRemington Power Tools 100271-01を使用するのを助ける技術的文書のことです。説明書は通常、全てのRemington Power Tools 100271-01ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Remington Power Toolsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Remington Power Tools 100271-01の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRemington Power Tools 100271-01の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Remington Power Tools 100271-01に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Remington Power Tools 100271-01デバイスの基本機能を使うにあたってのヒント。 Remington Power Tools 100271-01のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Remington Power Tools 100271-01に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRemington Power Tools 100271-01のメーカー/サービスへの連絡先に関する情報。

Remington Power Tools 100271-01についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもRemington Power Tools 100271-01の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRemington Power Tools 100271-01で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)