English dropdown-ico

Manual Remington Power Tools 100271-01

16 pages 0.5 mb
Download

Go to site of 16

Summary
  • Remington Power Tools 100271-01 - page 1

    ELECTRIC CHAIN S A W SECTION PAGE Symbol Information ............................................................ 2 Safety Warnings ................................................................. 3 Before Operating Chain Saw ....................................... 3 Kickback ...................................................................... 3 ...

  • Remington Power Tools 100271-01 - page 2

    2 100273 INFORMA TION SYMBOLS ! WARNING ICON G 001 Read Instruction Manual Do Not Expose to Rain or Use in Wet Conditions Remove Plug Immediately if Cable is Damaged or Cut Hold Chain Saw with Both Hands Beware of Kickback Hearing and Eye Protection Must Be Worn Safety Information Warnings Appears Throughout This Manual Pay close attention to them. ...

  • Remington Power Tools 100271-01 - page 3

    3 3 100273 BEFORE OPERATING CHAIN SAW 1. Read and understand this owner ’ s manual before operating chain saw. 2. Use chain saw for cutting wood only. Do not use for cutting any non-wood items. 3. Only well-instructed adults should operate chain saw. Never allow children to operate chain saw. First-time user should obtain informed, practical inst ...

  • Remington Power Tools 100271-01 - page 4

    4 100273 • Never try cutting through two logs at same time. Only cut one log at a time. • Do not bury guide bar nose or try plunge cut (boring into wood using guide bar nose). • Watch for shifting of wood or other forces that may pinch chain. • Use extreme caution when re-entering a previous cut. • Use low-kickback chain and guide bar sup ...

  • Remington Power Tools 100271-01 - page 5

    5 5 100273 Front Hand Guard Shield between front handle and guide bar. Protects left hand while using saw. When kickback occurs, the front hand guard is moved forward by the back of operator ’ s left hand. This stops the saw chain quickly, reducing the chance of serious injury. Front Handle Located at front of saw body. Guide Bar Metal bar that e ...

  • Remington Power Tools 100271-01 - page 6

    6 100273 ! WARNING ICON G 001 W ARNING Cutting edges on chain are sharp. Use protective gloves when handling chain. Figure 3 - Assembling Guide Bar, Chain, and Hand Guard Adjusting Block Adjusting Screw Sprocket Support Adjusting Plate Figure 4 - Part Locations for Assembling Guide Bar ASSEMBL Y UNP ACKING 1. Remove all items from carton. 2. Check ...

  • Remington Power Tools 100271-01 - page 7

    7 7 100273 SAW CHAIN TENSION ADJUSTMENT Note: For pre assembled models, the saw chain tension is properly set at factory. A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Follow steps below to readjust saw chain tension. 1. Before adjusting chain, make sure guide bar nuts are only fi nger ti ...

  • Remington Power Tools 100271-01 - page 8

    8 100273 EXTENSION CORDS Use proper extension cord with this chain saw. Use a HO7RN extension cord no less than 1.5 mm 2 at distances up to 30 meters. Use a ground fault circuit interrupter as part of the power supply system. Use an extension cord heavy enough to carry the current your saw will draw. An undersized cord will cause a voltage drop at ...

  • Remington Power Tools 100271-01 - page 9

    9 9 100273 OPERA TING CHAIN SA W Continued TRIMMING A TREE (Pruning) Trimming a tree is the process of cutting limbs from a living tree. Make sure your footing is fi rm. Keep feet apart. Divide your weight evenly on both feet. Follow directions below to trim a tree. 1. Make fi rst cut 15 centimeters from tree trunk on underside of limb. Use top o ...

  • Remington Power Tools 100271-01 - page 10

    10 100273 OPERA TING CHAIN SA W Continued Figure 14 - Limbing A Tree Limbing is removing branches from a fallen tree. Make sure your footing is fi rm. Keep feet apart. Divide your weight evenly on both feet. Do not remove larger limbs under tree that support log off ground. Remove each limb with one cut (see Figure 14). Clear cut limbs from work a ...

  • Remington Power Tools 100271-01 - page 11

    11 11 100273 OPERA TING CHAIN SA W Continued 2nd Cut 1st Cut Figure 16 - Bucking Log When Log Is Supported On One End 1st Cut 2nd Cut Figure 17 - Bucking Log When Log Is Supported On Both Ends Log Supported On One End 1. Make fi rst cut on underside of log (see Figure 16). Use top of guide bar to make this cut. Cut 1/3 through diameter of log. Thi ...

  • Remington Power Tools 100271-01 - page 12

    12 100273 CLEANING SAW BODY Keep saw body clean. Use a soft cloth dampened with a mild soap and water mixture. Wipe saw body to clean. CARE OF GUIDE BAR Uneven bar wear causes most guide bar problems. Incorrect sharpening of chain cutter and depth gauge settings often cause this. When bar wears unevenly, it widens guide bar groove (see Figure 18). ...

  • Remington Power Tools 100271-01 - page 13

    13 13 100273 CLEANING AND MAINTENANCE Continued Sharpening Cutters Use fi le guide for 30 ° fi ling. 1. Adjust chain for proper tension (see Saw Chain Tension Adjustment , page 7). 2. Clamp guide bar in vise to hold saw steady. Note: Do not clamp chain. 3. Press four millimeter round fi le (attached to fi le guide) into groove between top plat ...

  • Remington Power Tools 100271-01 - page 14

    14 100273 CLEANING AND MAINTENANCE Continued Replacing Saw Chain Replace chain when cutters are too worn to sharpen or when chain breaks. Only use replacement chain noted in this manual. Always include new drive sprocket when replacing chain. This will maintain proper driving of chain. Note: For proper chain and drive sprocket, see Replacement Part ...

  • Remington Power Tools 100271-01 - page 15

    15 15 100273 TROUBLESHOOTING OBSERVED FAULT Saw runs, but does not cut. Saw does not cut unless heavily forced. Cutting produces only sawdust with few large chips. Saw runs slow. Saw stalls easily. Motor of saw does not run when you squeeze trigger. Motor of saw runs, but chain does not move. Chain does not get oil. Chain comes off guide bar. Saw s ...

  • Remington Power Tools 100271-01 - page 16

    W ARRANTY INFORMA TION KEEP THIS WARRANTY Always specify model and serial numbers when writing the factory. We reserve the right to amend these speci fi cations at any time without notice. The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied. This product is warranted to be free from defect ...

Manufacturer Remington Power Tools Category Chainsaw

Documents that we receive from a manufacturer of a Remington Power Tools 100271-01 can be divided into several groups. They are, among others:
- Remington Power Tools technical drawings
- 100271-01 manuals
- Remington Power Tools product data sheets
- information booklets
- or energy labels Remington Power Tools 100271-01
All of them are important, but the most important information from the point of view of use of the device are in the user manual Remington Power Tools 100271-01.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Remington Power Tools 100271-01, service manual, brief instructions and user manuals Remington Power Tools 100271-01. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Remington Power Tools 100271-01.

Similar manuals

A complete manual for the device Remington Power Tools 100271-01, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Remington Power Tools 100271-01 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Remington Power Tools 100271-01.

A complete Remington Power Tools manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Remington Power Tools 100271-01 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Remington Power Tools 100271-01, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Remington Power Tools 100271-01, that we can find in the current document
3. Tips how to use the basic functions of the device Remington Power Tools 100271-01 - which should help us in our first steps of using Remington Power Tools 100271-01
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Remington Power Tools 100271-01
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Remington Power Tools 100271-01 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Remington Power Tools 100271-01?

Use the form below

If you did not solve your problem by using a manual Remington Power Tools 100271-01, ask a question using the form below. If a user had a similar problem with Remington Power Tools 100271-01 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)