Bacharach FT-10の取扱説明書

18ページ 0.18 mb
ダウンロード

ページに移動 of 18

Summary
  • Bacharach FT-10 - page 1

    1 of 18 3015-4568 Revision 0 9/11/03 Installation Guide Bacharach HGM300 to LonWorks FT-10 Communications Adapter Introduction The Bacharach HGM300 to LonWorks Comm unications Adapter enables an HGM300 Refrigerant Monitor to communicate with a LonWorks FT-10 Free Topology network. Zone PPM readings, flow status, refrigerant selections, and HGM inte ...

  • Bacharach FT-10 - page 2

    2 of 18 front side of the door. Position the adap ter board over the s tandoffs mounted on the HGM door. Install the five remaining 6- 32 screws through the board and into the standoffs and tighten. Connect power wiring from the HGM300’s 120V Auxiliary Power term inal block to the adapter board’s POWER terminal block. Use UL approved wire. W ir ...

  • Bacharach FT-10 - page 3

    3 of 18 If an RDM800 remote display IS to be used w ith the adapter, refer to Figure 3 for wiring details. Note that when the RDM800 is used, TWO RS-485 cables must be run betw een the HGM300 and RDM800, so plan accordingly. In either case, be sure to set the HGM300’s in ternal “Terminator” s lide switch next to the RS-485 terminal block to t ...

  • Bacharach FT-10 - page 4

    4 of 18 ...

  • Bacharach FT-10 - page 5

    5 of 18 Setting HGM Communication Address On Adapter See Figure 4 for the location of adapter dipswitch ‘A’. Switches 5-8 on the adapter’s ‘A ’ dipswitch are used to matc h the node address set on the HGM’s address dipswitch (on HGM main boa rd). Values from 0-15 are possible: HGM address A5 A6 A7 A8 ----------------- ------------------ ...

  • Bacharach FT-10 - page 6

    6 of 18 ...

  • Bacharach FT-10 - page 7

    7 of 18 Configuring the HGM300 with RDM800 or Laptop PC The only HGM parameters that are cha ngeable through LonWorks are the alarm thresholds. Configuring the HGM for refriger ant type and length of tubing for each zone (zero length to disable a zone ) must be done with the RDM800 remote display or a laptop PC. Refer to the appropriate Bacharach i ...

  • Bacharach FT-10 - page 8

    8 of 18 HGM Alarm Acknowledge Options Two alarm acknowledge options are s upported—Auto Acknowledge and Network Acknowledge. In the Auto Acknowledge mode, the HGM will clear its alarm outputs the next tim e the alarmed zone is sampled and its PP M has dropped below the alarm thresholds. No intervention from the LonW or ks network is necessary. In ...

  • Bacharach FT-10 - page 9

    9 of 18 LonWorks Objects and Network Variables The adapter contains one Node Object, sixteen Zone Objects, one Ge neral Status Object, and one Alarm Control Object. There is one Zone Object fo r each refrigerant sampling zone. Object 0 – The Node Object Network input variable nviRequest allows the user to requ est information from different objec ...

  • Bacharach FT-10 - page 10

    10 of 18 Network output variable nvoStatus returns the information requested by nviRequest. The status response will indicate the status of the object that received the request. The status bits supported are list ed above under RQ_REPORT_MASK. One nvoStatus response will be returned for each nviRequest. The configuration variable nciMaxStsSendT can ...

  • Bacharach FT-10 - page 11

    11 of 18 Objects 1-16 – Zone Objects There is one Zone Object for each sampling zone in the HGM300 (16 total): Network output variable nvoHgmZonePPM shows the m easured gas concentration for a particular zone. The value will range from 0-65535 PPM. Network output variable nvoHgmZoneStatus is a text string that displays inform ation about the zone ...

  • Bacharach FT-10 - page 12

    12 of 18 CRITICAL FAULT Some critical fault pr events normal zone PPM m easurement. (View nvoHgmFaults for details on fault type) HGM BUSY Occurs with RDM800 insta lled when certain scr eens are displayed. COMM FAULT 1 Comm failure between HGM and adapter. COMM FAULT 2 Comm failure between adapter internal processors. HGM WARMING UP HGM must go thr ...

  • Bacharach FT-10 - page 13

    13 of 18 Object 17 – General Status Objec t The General Status Object provides info rmation about any HGM300 internal faults present and shows which zone is currently being sampled: Network output variable nvoHgmFaultAlert reports whenever ANY fault is detected within the HGM or adapter. It is of type S NVT_switch. It is useful for binding to a F ...

  • Bacharach FT-10 - page 14

    14 of 18 HGM Busy (if RDM800 attached a nd showing certain screens)(bit 4) Comm Fault 1 (communications fail ed between HGM and adapter)(bit 3) Comm Fault 2 (internal communicati ons failed within adapter)(bit 2) Unused (bit 1) Unused (bit 0)(least significant b it) Network output variable nvoZ oneSampling shows which zone is currently being sample ...

  • Bacharach FT-10 - page 15

    15 of 18 Object 18 – Alarm Control Object The Alarm Control Object provides information about any alarm s which are present in the HGM. It also provides mechanisms fo r acknowledging alarm s, and for viewing and setting the Leak, Spill, and Evacuate alarm thresholds for each zone: Network input variable nviHgmAlarmAck has a single parameter (unsi ...

  • Bacharach FT-10 - page 16

    16 of 18 Network input variable nviSetZoneThresh allows Leak, Spill, and Eva cuate alarm thresholds (in PPM) to be set for each m onitoring zone. nviSetZoneThresh has four parameters to be set by the user: Zone Specifier: a number 1-16 specifies which zone is having its thresholds changed Leak Alarm Threshold: a number 0–65535 PPM Spill Alarm Thr ...

  • Bacharach FT-10 - page 17

    17 of 18 Network output variable nvoHgmZoneThresh displays the following in formation for the zone specified by nviGetZoneThresh: 1. Zone (1-16) whose alarm th resholds are being displayed 2. Leak Alarm Threshold in PPM (0-65535) 3. Spill Alarm Threshold in PPM (0-65535) 4. Evacuate Alarm Threshold in PPM (0-65535) To change the Leak, Spill, or Eva ...

  • Bacharach FT-10 - page 18

    18 of 18 LED 1 and LED 2 will normally show activ ity about every 15 seconds. Since the refrigerant monitoring process is fairly slow and new data is only available every 15 seconds or so, the adapter po lls the HGM at a slow rate to reduce the com munications burden on the HGM main processor. Agai n, commands com ing in from LonWorks might occasio ...

メーカー Bacharach カテゴリー Network Card

Bacharach FT-10のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- FT-10の取扱説明書
- Bacharachの製品カード
- パンフレット
- またはBacharach FT-10の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bacharach FT-10の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bacharach FT-10の取り付け説明書、サービスマニュアル、簡易説明書、またはBacharach FT-10のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bacharach FT-10の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bacharach FT-10デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBacharach FT-10を使用するのを助ける技術的文書のことです。説明書は通常、全てのBacharach FT-10ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bacharachの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bacharach FT-10の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBacharach FT-10の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bacharach FT-10に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bacharach FT-10デバイスの基本機能を使うにあたってのヒント。 Bacharach FT-10のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bacharach FT-10に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBacharach FT-10のメーカー/サービスへの連絡先に関する情報。

Bacharach FT-10についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBacharach FT-10の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBacharach FT-10で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)