a/d/s/ PQ40.2の取扱説明書

12ページ 0.69 mb
ダウンロード

ページに移動 of 12

Summary
  • a/d/s/ PQ40.2 - page 1

    analog and digital systems P Q 4 0 . 2 owner's manual 8900-3110 REV A ©2001 analog and digital systems, inc. www.adst.com ...

  • a/d/s/ PQ40.2 - page 2

    table of content s about this manual................................................................................................... 2 features of your PowerPlate TM .................................................................................. 2 warning and tips................................................................................ ...

  • a/d/s/ PQ40.2 - page 3

    specifications amplifier section PQ 40.2 power output 4 (watts) 1 4 channel 4 x 100 2 channel 2 x 300 power output 2 (watts) 2 4 x 150 fuse type 60 A maxi dimensions 13” x 16 1/8” x 2” distortion all channels driven <0.1% 20Hz to 20,000Hz frequency response ±1dB 10Hz to 30,000Hz signal-to-noise ratio full >90dB bandwidth @ rated output ...

  • a/d/s/ PQ40.2 - page 4

    warnings and tips Always disconnect the battery ground wire before doing any work on your vehicle. Reconnect the cable only after the installation is complete and the wiring has been checked to make sure that ther e are no problems. If your radio features a code type security system, be sure you know the code before disconnecting the battery! Y our ...

  • a/d/s/ PQ40.2 - page 5

    troubleshooting symptom possible cause action to take no output low or no remote turn-on check remote turn-on input voltage output at amplifier and correct as needed fuse blown check power wire integrity and reversed polarity, repair as needed and replace fuse power wires not connected check power wire and ground connections and repair or replace a ...

  • a/d/s/ PQ40.2 - page 6

    signal sources Due to the wide input level adjustment range, all a/d/s/ PowerPlates TM can be driven with either a conventional preamplifier drive signal or the amplifier signal from a powered source unit. This makes the PowerPlate TM perfect for upgrading an OEM (Original Equipment Manufacturer) stereo system while retaining the factory installed ...

  • a/d/s/ PQ40.2 - page 7

    Constant bass circuit T o mix sub-bass information into channels 1/2 and 3/4, select a low-pass crossover point, and use the level controls to set the level of sub-bass signal sent to channels 1/2 and 3/4. Using the AC502 (optional) The AC502 remote level control, available as an accessory from your a/d/s/ dealer, may be used with your PowerPlate T ...

  • a/d/s/ PQ40.2 - page 8

    System 2 – PQ40 used in 3-channel mode with high-pass main speakers and low-pass subwoofer . Note: Although shown as 2-channel, the source unit may be either 2 or 4-channel depending on the setting of the 2/4 channel switch. System 3 – PQ40 used in 4-channel mode with 2 channels high-pass, 2 channels low-pass or bandpass. Depending on the cross ...

  • a/d/s/ PQ40.2 - page 9

    Internal signal routing 2-channel/4-channel input switch – routes RCA input from channels 1/2 to channels 3/4. When the switch is engaged, channel 1 input is routed to both amplifier channels 1 and 3 with input channel 2 routed to amplifier channels 2 and 4. Switch in the engaged position. When the switch is disengaged, channels 1, 2, 3, and 4 re ...

  • a/d/s/ PQ40.2 - page 10

    System 6 – Two PQ40s, both set up as shown in system 3. One amp drives bi-amped midranges and tweeters with the second driving rear fill speakers and subwoofers. speaker connections for stereo configurations Minimum recommended impedance is 2 Ohm stereo. Speaker terminals accept up to AWG #12 speaker wire. speaker connections for bridged configur ...

  • a/d/s/ PQ40.2 - page 11

    installation 1. Disconnect the battery ground cable. Reconnect the ground cable only after the installation is complete and the wiring has been checked to make sure that there are no problems. If your radio features a code type security system, be sure you know the code before disconnecting the battery! 2. Run a minimum AWG #8 power wire directly f ...

  • a/d/s/ PQ40.2 - page 12

    12 11 ...

メーカー a/d/s/ カテゴリー Car Stereo System

a/d/s/ PQ40.2のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PQ40.2の取扱説明書
- a/d/s/の製品カード
- パンフレット
- またはa/d/s/ PQ40.2の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、a/d/s/ PQ40.2の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、a/d/s/ PQ40.2の取り付け説明書、サービスマニュアル、簡易説明書、またはa/d/s/ PQ40.2のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、a/d/s/ PQ40.2の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

a/d/s/ PQ40.2デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがa/d/s/ PQ40.2を使用するのを助ける技術的文書のことです。説明書は通常、全てのa/d/s/ PQ40.2ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

a/d/s/の取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. a/d/s/ PQ40.2の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははa/d/s/ PQ40.2の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。a/d/s/ PQ40.2に関してこのドキュメントで見つけることができる全てのヒントの目次
3. a/d/s/ PQ40.2デバイスの基本機能を使うにあたってのヒント。 a/d/s/ PQ40.2のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。a/d/s/ PQ40.2に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるa/d/s/ PQ40.2のメーカー/サービスへの連絡先に関する情報。

a/d/s/ PQ40.2についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもa/d/s/ PQ40.2の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがa/d/s/ PQ40.2で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)