Bedienungsanleitung a/d/s/ PQ40.2

12 Seiten 0.69 mb
Download

Zur Seite of 12

Summary
  • a/d/s/ PQ40.2 - page 1

    analog and digital systems P Q 4 0 . 2 owner's manual 8900-3110 REV A ©2001 analog and digital systems, inc. www.adst.com ...

  • a/d/s/ PQ40.2 - page 2

    table of content s about this manual................................................................................................... 2 features of your PowerPlate TM .................................................................................. 2 warning and tips................................................................................ ...

  • a/d/s/ PQ40.2 - page 3

    specifications amplifier section PQ 40.2 power output 4 (watts) 1 4 channel 4 x 100 2 channel 2 x 300 power output 2 (watts) 2 4 x 150 fuse type 60 A maxi dimensions 13” x 16 1/8” x 2” distortion all channels driven <0.1% 20Hz to 20,000Hz frequency response ±1dB 10Hz to 30,000Hz signal-to-noise ratio full >90dB bandwidth @ rated output ...

  • a/d/s/ PQ40.2 - page 4

    warnings and tips Always disconnect the battery ground wire before doing any work on your vehicle. Reconnect the cable only after the installation is complete and the wiring has been checked to make sure that ther e are no problems. If your radio features a code type security system, be sure you know the code before disconnecting the battery! Y our ...

  • a/d/s/ PQ40.2 - page 5

    troubleshooting symptom possible cause action to take no output low or no remote turn-on check remote turn-on input voltage output at amplifier and correct as needed fuse blown check power wire integrity and reversed polarity, repair as needed and replace fuse power wires not connected check power wire and ground connections and repair or replace a ...

  • a/d/s/ PQ40.2 - page 6

    signal sources Due to the wide input level adjustment range, all a/d/s/ PowerPlates TM can be driven with either a conventional preamplifier drive signal or the amplifier signal from a powered source unit. This makes the PowerPlate TM perfect for upgrading an OEM (Original Equipment Manufacturer) stereo system while retaining the factory installed ...

  • a/d/s/ PQ40.2 - page 7

    Constant bass circuit T o mix sub-bass information into channels 1/2 and 3/4, select a low-pass crossover point, and use the level controls to set the level of sub-bass signal sent to channels 1/2 and 3/4. Using the AC502 (optional) The AC502 remote level control, available as an accessory from your a/d/s/ dealer, may be used with your PowerPlate T ...

  • a/d/s/ PQ40.2 - page 8

    System 2 – PQ40 used in 3-channel mode with high-pass main speakers and low-pass subwoofer . Note: Although shown as 2-channel, the source unit may be either 2 or 4-channel depending on the setting of the 2/4 channel switch. System 3 – PQ40 used in 4-channel mode with 2 channels high-pass, 2 channels low-pass or bandpass. Depending on the cross ...

  • a/d/s/ PQ40.2 - page 9

    Internal signal routing 2-channel/4-channel input switch – routes RCA input from channels 1/2 to channels 3/4. When the switch is engaged, channel 1 input is routed to both amplifier channels 1 and 3 with input channel 2 routed to amplifier channels 2 and 4. Switch in the engaged position. When the switch is disengaged, channels 1, 2, 3, and 4 re ...

  • a/d/s/ PQ40.2 - page 10

    System 6 – Two PQ40s, both set up as shown in system 3. One amp drives bi-amped midranges and tweeters with the second driving rear fill speakers and subwoofers. speaker connections for stereo configurations Minimum recommended impedance is 2 Ohm stereo. Speaker terminals accept up to AWG #12 speaker wire. speaker connections for bridged configur ...

  • a/d/s/ PQ40.2 - page 11

    installation 1. Disconnect the battery ground cable. Reconnect the ground cable only after the installation is complete and the wiring has been checked to make sure that there are no problems. If your radio features a code type security system, be sure you know the code before disconnecting the battery! 2. Run a minimum AWG #8 power wire directly f ...

  • a/d/s/ PQ40.2 - page 12

    12 11 ...

Produzent a/d/s/ Kategorie Car Stereo System

Dokumente, die wir vom Produzenten des Geräts a/d/s/ PQ40.2 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen a/d/s/
- Bedienungsanleitungen PQ40.2
- Produktkarten a/d/s/
- Informationsbroschüren
- oder Energieetiketten a/d/s/ PQ40.2
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung a/d/s/ PQ40.2.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen a/d/s/ PQ40.2, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen a/d/s/ PQ40.2. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts a/d/s/ PQ40.2 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts a/d/s/ PQ40.2, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von a/d/s/ PQ40.2 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von a/d/s/ PQ40.2 verständlich ist.

Eine gänzliche Bedienungsanleitung von a/d/s/ sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von a/d/s/ PQ40.2 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von a/d/s/ PQ40.2 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich a/d/s/ PQ40.2, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts a/d/s/ PQ40.2 - die uns die ersten Schritte während der Nutzung von a/d/s/ PQ40.2 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit a/d/s/ PQ40.2 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von a/d/s/ PQ40.2 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich a/d/s/ PQ40.2?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit a/d/s/ PQ40.2 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit a/d/s/ PQ40.2 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)