Ruger Hunting Equipmentの取扱説明書

47ページ 0.75 mb
ダウンロード

ページに移動 of 47

Summary
  • Ruger Hunting Equipment - page 1

    INSTRUCTION MANUAL FOR RUGER ® MINI THIR TY RIFLE AUTOLOADING RIFLE NOT FOR USE WITH MINI-14 RIFLES (cal. .223) S For Product Service on This Model Please Call: (603) 865-2442 (See p. 34) STURM, RUGER & Company , Inc. Southport, Connecticut 06890 U.S.A. THIS INSTRUCTION MANUAL SHOULD AL W A YS ACCOMP ANY THIS FIREARM AND BE TRANSFERRED WITH IT ...

  • Ruger Hunting Equipment - page 2

    W ARNING “Children are attracted to and can operate firearms that can cause severe injuries or death. Prevent child access by always keeping guns locked away and unloaded when not in use. If you keep a loaded firearm where a child obtains and improperly uses it, you may be fined or sent to prison.” ADVERTENCIA State-By-State W arnings Certain s ...

  • Ruger Hunting Equipment - page 3

    Maine: “ENDANGERING THE WELF ARE OF A CHILD IS A CRIME. IF YOU LEA VE A FIREARM AND AMMUNITION WITHIN EASY ACCESS OF A CHILD, YOU MA Y BE SUBJECT TO FINE, IMPRISONMENT OR BOTH. KEEP FIREARMS AND AMMUNITION SEP ARA TE. KEEP FIREARMS AND AMMUNITION LOCKED UP . USE TRIGGER LOCKS.” Mar yland: “W ARNING: Children can operate firearms which may cau ...

  • Ruger Hunting Equipment - page 4

    4 New Jersey: “IT IS A CRIMINAL OFFENSE T O LEA VE A LOADED FIREARM WITHIN EASY ACCESS OF A MINOR.” New Y ork City: “THE USE OF A LOCKING DEVICE OR SAFETY LOCK IS ONL Y ONE ASPECT OF RESPONSIBLE FIREARMS ST ORAGE. FIREARMS SHOULD BE ST ORED UNLOADED AND LOCKED IN A LOCA TION THA T IS BOTH SEP ARA TE FROM THEIR AMMUNITION AND INACCESSIBLE TO C ...

  • Ruger Hunting Equipment - page 5

    • Always keep your firearm pointed in a safe direction, including when you are installing or removing your locking device. • Always verify that your firearm is completely unloaded before installing your locking device. • Do not install locking devices in the trigger guard; always keep your fingers, clamp and locking device outside the trigger ...

  • Ruger Hunting Equipment - page 6

    6 Correct Installation of Lock For Ruger ® Mini Thrity Rifles Onl y 3. Open the action completely . Use the bolt lock to keep the action open during installation of the locking device. 4. Apply the lock by placing the shackle of the lock into your Ruger ® Mini Thirty Rifle as shown below . 5. Close the lock by pressing the shackle into the body o ...

  • Ruger Hunting Equipment - page 7

    7 FIREARMS SAFETY -YOUR RESPONSIBILITY SAFETY MUST BE THE FIRST AND CONST ANT CONSIDERA TION OF EVER Y PERSON WHO HANDLES FIREARMS AND AMMUNITION. This Instruction Manual is designed to assist you in learning how to use and care for your RUGER ® MINI THIRTY RIFLE properly . Please contact us if you have any questions about it. Only when you are ce ...

  • Ruger Hunting Equipment - page 8

    W ARNING–AL TERA TIONS This product was designed to function properly in its original condition. Alterations can make it unsafe. Do not alter any part or add or substitute parts or accessories not made by Sturm, Ruger & Co. Inc. DO NOT AL TER ANY GUN 8 FIREARMS ARE DANGEROUS WEAPONS– READ THE INSTRUCTIONS AND W ARNINGS IN THIS MANUAL THOROU ...

  • Ruger Hunting Equipment - page 9

    9 Figure 2 . In this illustration the frequently used operating components are identified. Note that the safety is rearward in the trigger guard and is therefore in its “ON” (safe) position. The Mini Thirty Rifle incorporates a unique patented buffer system which re- directs and effectively absorbs the shock of the slide block striking the rece ...

  • Ruger Hunting Equipment - page 10

    10 THE BOL T LOCK The Mini Thirty Rifle is designed so that the bolt remains open after the last shot has been fired, provided there is a magazine in the rifle. When the magazine is empty , the magazine follower actuates the bolt lock which is designed to retain the bolt and slide in their rearward position. W ARNING: The bolt lock is not a safety ...

  • Ruger Hunting Equipment - page 11

    Death, serious injury , and damage can result from the use of wrong ammunition, bore obstructions, powder overloads, or incorrect cartridge components. Even the strongest gun can be “blown up” as a result of excess pressure. Always wear shooting glasses and hearing protectors. IMPROPER AMMUNITION DESTROYS GUNS 11 W ARNING – AMMUNITION AMMUNIT ...

  • Ruger Hunting Equipment - page 12

    Ruger Mini Thirty Magazine (Correct) For Caliber 7.62 x 39mm Ammunition Only Bottom T op Side Bottom T op Side Never attempt to use caliber .223 ammunition in Ruger Mini Thirty rifles, as it will not chamber correctly and will “jam” the action.These smaller cases will split upon firing in the larger Mini Thirty chamber , resulting in the releas ...

  • Ruger Hunting Equipment - page 13

    INSERTING THE MAGAZINE See Figure 6. The magazine may be inserted with the bolt either in the closed or open position (See “Bolt Lock” section p. 10). 1. Hold the magazine at an angle as shown and insert all the way up into the magazine well. NOTE: There is a hole in the top-front portion of the magazine that mates with a stud on the inside of ...

  • Ruger Hunting Equipment - page 14

    The bolt automatically opens and shuts quickly while firing. Keep face and hands away from it. Hot brass and powder gas is ejected quickly and can burn you. The rifle should be fired from the right shoulder . Always wear shooting glasses and hearing protectors. BOL T OPENS FAST– HOT BRASS EJECTED 14 TO LOAD AND FIRE (WITH MAGAZINE) Practice this ...

  • Ruger Hunting Equipment - page 15

    15 If dropped or struck with the safety “off”, the rifle may fire. Keep chamber empty unless actually firing! Keep safety “on” unless actually firing! ANY GUN MA Y FIRE IF DROPPED W ARNING – HANDLING SAFETY IN "OFF" (FIRE) POSITION 9. Immediately following the firing of a shot, and if a subsequent shot is not to be fired at once ...

  • Ruger Hunting Equipment - page 16

    So that the rifle can be used as a single loader , it will fire whether or not a magazine is in the gun if a cartridge is chambered. Removing magazine does not unload rifle! T o unload, first remove magazine, then pull bolt to rear , eject chambered cartridge, and visually inspect chamber . The safety should always be in the “on” (safe) positio ...

  • Ruger Hunting Equipment - page 17

    17 CORRECT UNLOADING SEQUENCE 1 3a 2 Safety "ON" 3b 4 2. Remove the magazine. REMEMBER that even though the magazine has been removed, a cartridge remaining in the chamber can still be fired! 3. Pull the slide handle all the way to the rear , extracting and ejecting the cartridge in the chamber . When the bolt is fully retracted, push ...

  • Ruger Hunting Equipment - page 18

    TO RELOAD THE RIFLE 1. Firing all cartridges in the magazine and the chamber will cause the bolt to automatically lock open. Keep the rifle pointed in a safe direction. Put the safety “ON”. Reloading can be accomplished by pressing forward on the magazine latch with the thumb or forefinger . The magazine will fall free of the rifle of its own w ...

  • Ruger Hunting Equipment - page 19

    Before loading or shooting the Mini Thirty rifle, be certain the bore is unobstructed. Firing the rifle with any obstruction in the bore may result in severe damage to the rifle and serious injury to the shooter and other persons nearby. A MISFIRE or unusual report (sound) upon firing is always a signal to cease firing immediately and after waiting ...

  • Ruger Hunting Equipment - page 20

    20 c) Retract the slide handle and lock it in the open position by pressing in the bolt lock plunger in the top of the receiver . Retracting the slide handle should remove the cartridge case. Be certain the safety is in the “ON” position. d) Check the chamber to be certain there is no cartridge case in it -- if there is, extract it before proce ...

  • Ruger Hunting Equipment - page 21

    21 2. When attempting to free a jammed cartridge, do not use any type of tool that is likely to act as a “firing pin” and discharge the cartridge should the tool impact on the primer . Never use a cartridge as a “tool”. 3. After clearing a jam, inspect the gun mechanism to determine if dirt or debris might be the cause of the problem. Exces ...

  • Ruger Hunting Equipment - page 22

    A cartridge can be “discharged” before it is chambered if its primer receives a sharp blow . If a cartridge hangs up, jams, or binds when being chambered or when being fed from the magazine into the chamber , do not attempt to force it into the chamber by pushing or striking the bolt. Any jam or feeding problem is a signal to immediately stop u ...

  • Ruger Hunting Equipment - page 23

    Always unload a firearm before cleaning, lubrication, disassembly or assembly . UNLOAD BEFORE CLEANING 23 W ARNING – DISASSEMBL Y 1 3a 2 Safety "ON" 3b 4 DISASSEMBL Y Be Sure Rifle Is Unloaded! Although The Mini Thirty Rifle can be disassembled, reassembled, and cleaned in almost any surrounding, it is preferrable to carry out these ...

  • Ruger Hunting Equipment - page 24

    Figure 9 Figure 10 3. Use a 1/4” diameter steel rod, punch, screwdriver shank, or other suitable instrument inserted into the hole in the rear of the trigger guard as a lever to spring open the trigger guar d from its latched position (See Fig. 9). W ARNING: Do not use a cartridge to unlatch the trigger guard because of the danger of loosening th ...

  • Ruger Hunting Equipment - page 25

    25 Figure 15 NOTE: The Mini Thirty Rifle is like the M1 Garand and many other types of autoloading rifles in that the hammer can fall if the trigger is pulled when the bolt is partially retracted. It is important for the shooter to realize that the firing pin cannot contact the cartridge until the bolt is safely locked, regardless of the position o ...

  • Ruger Hunting Equipment - page 26

    26 Removal of the gas block assembly is not necessary and is not advisable. The gas block assembly is factory fitted using special fixtures and torque tools. Attempting to fit the gas block assembly without the required special equipment can result in damage to the components and malfunctioning of the rifle. Further disassembly of the RUGER ® MINI ...

  • Ruger Hunting Equipment - page 27

    3. Final reassembly of rifle: a. Replace stock by inserting its front end into the gas block at a slight angle. When the stock is correctly seated into the gas block, the stock can be swung down into full contact with the receiver . b. Insert the opened trigger housing assembly , safety “ON”, into the stock (the hammer must be cocked prior to i ...

  • Ruger Hunting Equipment - page 28

    screwdriver to push the magazine bottom rearward as you push down on the spring-loaded bottom retainer . After the magazine bottom has been slid rearward off the magazine shell, car efully raise the rear end of the bottom retainer so that its two small lugs can be slid out the rear of the magazine and car efully remove the bottom retainer . CAUTION ...

  • Ruger Hunting Equipment - page 29

    Firing a rifle with oil, grease, or any other material even partially obstructing the bore may result in damage to the rifle and serious injury to the shooter and those nearby . Do not spray or apply lubricants directly on ammunition. If the powder of a cartridge is affected by the lubricant, it may not be ignited, but the primer firing may push th ...

  • Ruger Hunting Equipment - page 30

    Never place or store any firearm in such a manner that it may be dislodged. Firearms should always be stored securely and unloaded, away from children and careless adults. Use the locking device originally supplied with this firearm for storage. The use of a locking device or safety lock is only one aspect of responsible firearms storage. For incre ...

  • Ruger Hunting Equipment - page 31

    MAINTENANCE OF ST AINLESS STEEL RIFLES Firearms and components made of stainless steel are relatively more resistant to corrosion than those of blued steel. However , in the interest of proper operation and long life of a stainless steel firearm, inspect it frequently and clean, lubricate and apply an appropriate rust preventative. Sometimes discol ...

  • Ruger Hunting Equipment - page 32

    32 1. Fold rear sight down. Disassemble one ring and reassemble over the scope body between the turret and the eyepiece. Remember - the lug on the base should be on the front side of the scope. 2. Install the four top screws. Do not tighten. 3. Disassemble the other ring and install it on the forward section of the scope tube with the lug forwardly ...

  • Ruger Hunting Equipment - page 33

    33 SUGGESTED SIGHT PICTURE The front sight is aligned in the center of the rear sight aperture (“peep”) and the target (bullseye) is positioned to appear as if it is sitting on top of the front sight. ELEV A TION ADJUSTMENT : T o move the bullet impact point up or down , move the elevation slide (the “peep”) by loosening both its screws (us ...

  • Ruger Hunting Equipment - page 34

    34 SHIPPING FIREARMS FOR REP AIR RUGER ® MINI THIRTY RIFLES returned to the factory for repair should be sent to: Sturm, Ruger & Company , Inc., Product Service Department, 411 Sunapee St., Newport, New Hampshire 03773. T elephone (603) 865-2442. Guns should be sent prepaid. We will not accept collect shipments. The Federal Gun Control Act, as ...

  • Ruger Hunting Equipment - page 35

    35 CAUTION: A gun containing modified, broken, malfunctioning, or badly worn parts should not be fired. ORDERING P ARTS Please contact the New Hampshire Product Service Department for parts availability and current prices. All parts orders for the RUGER ® MINI THIRTY RIFLE should be sent to: Sturm, Ruger & Co., Inc., Product Service Department ...

  • Ruger Hunting Equipment - page 36

    36 RUGER ® MINI THIRTY RIFLE P ARTS LIST Design, prices and specifications subject to change without notice. SPECIFY MODEL WHEN ORDERING (See Exploded View on Page 41) Part Name Part No. Model * Barrel, Specify Model & Serial Number 0M8002 Mini Thirty - Blued Model * Barrel, Specify Model & Serial Number K0M8002 Mini Thirty - Stainless Mod ...

  • Ruger Hunting Equipment - page 37

    37 Part Name Part No. Model Butt Plate Screw , (2 Req’d.) B-64 Mini Thirty - Wood Stock Models Butt Plate Screw , (2 Req’d.) B-91 Mini Thirty - Synthetic Stock Model Ejector Bolt Stop MS03211 Mini Thirty - Blued Model Ejector Bolt Stop KMS03211 Mini Thirty - Stainless Models Extractor MS01403 Mini Thirty - Blued Model Extractor KMS01403 Mini Th ...

  • Ruger Hunting Equipment - page 38

    Part Name Part No. Model Hammer Strut MS01800 Mini Thirty - Blued Model Hammer Strut KMS01800 Mini Thirty - Stainless Models Hammer Strut Assembly MS01800A Mini Thirty - Blued Model Hammer Strut Assembly KMS01800A Mini Thirty - Stainless Models Handguard Assembly , Fiberglass MFH All Mini Thirty Models Magazine, Complete, 5-Shot Capacity MAG/762 Al ...

  • Ruger Hunting Equipment - page 39

    Part Name Part No. Model Safety Assembly MS13800A Mini Thirty - Blued Model Safety Assembly KMS13800A Mini Thirty - Stainless Model Safety Detent Spring KMS04900 All Mini Thirty Models Safety Spring Retaining Pin MS06200 Mini Thirty - Blued Model Safety Spring Retaining Pin KMS06200 Mini Thirty - Stainless Models Scope Ring Clamp D-74 Mini Thirty - ...

  • Ruger Hunting Equipment - page 40

    40 Part Name Part No. Model Sling Swivel, Front MS07500 Mini Thirty - Blued Model Sling Swivel, Front KMS07500 Mini Thirty - Stainless Models Stock (Wood w/Butt Plate Attached) MS00403 All Mini Thirty Models Stock Assembly , Complete, Synthetic KMS30427 Mini Thirty - Synthetic Stock Model Stock Reinforcement Assembly MS20702 Mini Thirty - Blued Mod ...

  • Ruger Hunting Equipment - page 41

    41 RUGER ® MINI THIRTY RIFLE EXPLODED VIEW ...

  • Ruger Hunting Equipment - page 42

    42 THE BASIC RULES OF SAFE FIREARMS HANDLING We believe that Americans have a right to purchase and use firearms for lawful purposes. The private ownership of firearms in America is traditional, but that ownership imposes the responsibility on the gun owner to use his firearms in a way which will ensure his own safety and that of others. When firea ...

  • Ruger Hunting Equipment - page 43

    43 A safe direction must take into account the fact that a bullet may penetrate a wall, ceiling, floor , window , etc., and strike a person or damage property . Make it a habit to know exactly where the muzzle of your gun is pointing whenever you handle it, and be sure that you are always in control of the direction in which the muzzle is pointing, ...

  • Ruger Hunting Equipment - page 44

    44 5. BE SURE OF YOUR T ARGET BEFORE YOU SHOOT . Don’t shoot unless you know exactly where your bullet is going to strike. Be sure of the bullet stop behind your target, even when dry-firing with an unloaded gun. If you are in the field hunting, do not fire at a movement or noise. T ake the time to be absolutely certain of your target before you ...

  • Ruger Hunting Equipment - page 45

    8. DON’T SHOOT A T A HARD SURF ACE, OR A T W A TER. Bullets can glance off many surfaces like rocks or the surface of water and travel in unpredictable directions with considerable velocity . 9. NEVER TRANSPORT A LOADED FIREARM. Firearms should always be unloaded before being placed in a vehicle. A suitable carrying case or scabbard should be use ...

  • Ruger Hunting Equipment - page 46

    A BRIEF ACCOUNT OF AN EXTRAORDINAR Y ACHIEVEMENT : RUGER FIREARMS One of the few American firearms manufacturers whose management has remained in the same family since starting in business, Sturm, Ruger & Company , Inc., had its beginning in a small machine shop occupying a rented frame building in Southport, Connecticut. In January , 1949, wit ...

  • Ruger Hunting Equipment - page 47

    WHY NO W ARRANTY CARD HAS BEEN P ACKED WITH THIS NEW RUGER FIREARM The Magnuson-Moss Act (Public Law 93-637) does not require any seller or manufacturer of a consumer product to give a written warranty . It does provide that if a written warranty is given, it must be designated as “limited” or as “full” and sets minimum standards for a “f ...

メーカー Ruger カテゴリー Hunting Equipment

Ruger Hunting Equipmentのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Hunting Equipmentの取扱説明書
- Rugerの製品カード
- パンフレット
- またはRuger Hunting Equipmentの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Ruger Hunting Equipmentの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Ruger Hunting Equipmentの取り付け説明書、サービスマニュアル、簡易説明書、またはRuger Hunting Equipmentのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Ruger Hunting Equipmentの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Ruger Hunting Equipmentデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRuger Hunting Equipmentを使用するのを助ける技術的文書のことです。説明書は通常、全てのRuger Hunting Equipmentユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Rugerの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Ruger Hunting Equipmentの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRuger Hunting Equipmentの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Ruger Hunting Equipmentに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Ruger Hunting Equipmentデバイスの基本機能を使うにあたってのヒント。 Ruger Hunting Equipmentのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Ruger Hunting Equipmentに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRuger Hunting Equipmentのメーカー/サービスへの連絡先に関する情報。

Ruger Hunting Equipmentについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもRuger Hunting Equipmentの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRuger Hunting Equipmentで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)