-
Ruger 77/50 - page 1
INSTRUCTION MANUAL FOR RUGER ® MODEL 77/50 TM INLINE MUZZLELOADING BLACK POWDER PERCUSSION RIFLE For Product Service on This Model Please Call: (603) 863-3300 (See p. 38) STURM, RUGER & Company , Inc. Southport, Connecticut 06490 U.S.A. THIS INSTRUCTION MANUAL SHOULD AL W A YS ACCOMP ANY THIS FIREARM AND BE TRANSFERRED WITH IT UPON CHANGE OF O ...
-
Ruger 77/50 - page 2
FIREARMS SAFETY -YOUR RESPONSIBILITY SAFETY MUST BE THE FIRST AND CONST ANT CONSIDERA TION OF EVER Y PERSON WHO HANDLES FIREARMS AND AMMUNITION. This Instruction Manual is designed to assist you in learning how to use and care for your RUGER ® MODEL 77/50 TM muzzleloading rifle properly . Only when you are certain you fully understand the Manual a ...
-
Ruger 77/50 - page 3
W ARNING–AL TERA TIONS This product was designed to function properly in its original condition. Alterations can make it unsafe. Do not alter any part or add or substitute parts or accessories not made by Sturm, Ruger & Co. Inc. DO NOT AL TER ANY GUN ! 3 ! FIREARMS ARE DANGEROUS WEAPONS – MUZZLELOADING BLACK POWDER FIREARMS REQUIRE SPECIAL ...
-
Ruger 77/50 - page 4
The RUGER ® MODEL 77/50 is a muzzleloading, percussion rifle intended for use with black powder , percussion caps, soft lead and jacketed “saboted” projectiles. It has a precision rifled barrel with a 1-in-28” rifling twist. It does not fire conventional cartridges, but is instead loaded from the muzzle of the barrel. It is of bolt-action op ...
-
Ruger 77/50 - page 5
Figure 1. Components frequently referred to are identified. In these photographs the cocking piece is shown cocked (protruding from the rear of the bolt sleeve) revealing the disassembly hole in the lower portion of the cocked piece. The bolt stop (on the left side of the receiver) permits the bolt to be withdrawn simply by pressing down lightly wi ...
-
Ruger 77/50 - page 6
6 OPERA TION OF SAFETY The RUGER ® MODEL 77/50 rifle has a three position safety . The safety selector is located at the right of the bolt sleeve. The safety selector can be moved from the “Fire” position to its two other positions (“Load-Unload” and “Safe”) only when the striker is cocked. Fully raising the bolt handle cocks the strik ...
-
Ruger 77/50 - page 7
Keep the safety on unless actually firing. Always move the safety fully to its intended position and check it. The safety has three positions –“SAFE,” “LOAD-UNLOAD,” and “FIRE.” Never depend on a safety mechanism or any other mechanical device to justify careless handling or permitting the rifle to point in an unsafe direction. The on ...
-
Ruger 77/50 - page 8
Death, serious injury , and damage can result from the use of wrong ammunition, bore obstructions, powder overloads, or incorrect components. Always wear shooting glasses and hearing protectors. Never use smokeless powder in any muzzleloader! Never fire an unknown powder charge. If you are uncertain as to which components your rifle is loaded with, ...
-
Ruger 77/50 - page 9
Black Powder is an extremely sensitive propellant and is readily ignited by heat, spark, static electricity , friction, pressure, impact, etc. Unlike smokeless powder , Black Powder will ignite with great violence and rapidity even when unconfined. Black Powder should be handled only in very small quantities. Never pour powder dir ectly fr om a fla ...
-
Ruger 77/50 - page 10
10 responsibility to select the proper lead ball/patch combination of a lubricated conical lead bullet that fits securely in the bore, yet is not excessively difficult to load, particularly after a shot or two of black powder fouling has built up in the bore. Never load multiple projectiles into the barrel. The rearmost projectile slamming into the ...
-
Ruger 77/50 - page 11
Percussion caps are designed to fire as the result of a blow (“percussion”). A capped rifle loaded with powder and ball is fully loaded and will fire if the cap is struck. Never clean, lubricate, disassemble, or work on a rifle while it is capped or loaded. Never install, remove, or carry a capped nipple or breech plug. Always remove the percus ...
-
Ruger 77/50 - page 12
12 INSERTING THE BOL T 1. Be certain the barrel is empty by pointing the muzzle upward towards a light source and glancing through the rear of the action at the rear end of the nipple. Y ou should see light through the hole in the nipple, indicating that the barrel is empty . Keep the muzzle pointed in a safe direction, and keep your fingers off th ...
-
Ruger 77/50 - page 13
Know the bore diameter of your rifle you are loading and load projectiles of only correct diameter into it! Either a too tight or too loose projectile can cause a burst barrel, resulting in serious injury to the shooter or bystanders. This rifle is designed to use a .500” projectile (or a .490” projectile with a .010 - .015” thick patch), a # ...
-
Ruger 77/50 - page 14
14 C. Using a dipper or other single-charge measure, pour the desired amount of powder into the front opening (muzzle) of the barrel. (See Fig. 6) Never exceed the powder charge recommended for the projectile you have selected from a reputable black powder loading manual. Do not pour powder directly from the flask or other powder container (See “ ...
-
Ruger 77/50 - page 15
F . Remove the ramrod from under the barrel by pulling it downward out of its recess in the barrel and then forward (upward) out of the stock and ramrod thimble. Grasp the ramrod around its side and, with a firm even stroke, seat the bullet firmly on the powder charge. Do not push down on the ramrod tip with the palm of your hand, in the event that ...
-
Ruger 77/50 - page 16
4. CAPPING THE NIPPLE: Remember that the safest way to carry any loaded muzzleloading rifle is uncapped. Cap it only just before you are immediately ready to fire. See “Handling Warning”, p. 17. Be sure you use only #11 percussion caps of good quality and correct size. With the bolt open, carefully place a #11 cap on to the nipple. An inline ca ...
-
Ruger 77/50 - page 17
If this rifle is to be carried loaded, certain precautions must be observed in the interest of safety . It is safest to carry any muzzleloader with no percussion cap on the nipple. The gun should never be carried with the striker resting on a percussion cap. Under such circumstances, a light accidental blow to the striker can readily cause the gun ...
-
Ruger 77/50 - page 18
Black powder is extremely sensitive and a powder charge poured down the barrel after firing a shot can readily be ignited by an ember of partially burned powder or glowing patch fragment in the bore. Pushing a projectile down onto a powder charge can “fan” an ember into igniting the powder charge and firing the rifle. Always wait one minute bef ...
-
Ruger 77/50 - page 19
Never carry the rifle loaded with the safety selector in the “FIRE” position. If dropped or struck with the safety off, the rifle may fire. Such a discharge can occur with or without the trigger being directly struck or touched. Never rest a loaded rifle against any object (wall, fence, vehicle, tree, etc.) because there is always the possibili ...
-
Ruger 77/50 - page 20
20 TO UNLOAD (Keep rifle pointed in a safe direction) Completely unload the rifle immediately when you are finished shooting (by removing cap, powder and ball), or fire it into a safe backstop. It is much easier and safer to fir e any muzzleloading fir ear m rather than attempt to unload it. However , if this is impossible, or if you are uncertain ...
-
Ruger 77/50 - page 21
5. Using the breech plug wrench supplied, carefully unscrew the breech plug from the chamber . Keep it in the breech plug wrench and remove it out the rear of the receiver . (See Figs. 15a & 15b) 6. Carefully elevate the muzzle and dump the powder out of the rear of the barrel into a container . (See Fig. 16) 7. Place some lubricating oil into ...
-
Ruger 77/50 - page 22
Never clean, lubricate, disassemble or work on a rifle while it is loaded or capped. Never install or remove a capped nipple. A capped nipple can discharge the rifle if struck. Always unload any firearm before cleaning, lubrication, disassembly , or assembly . Read instructions before disassembling gun. UNLOAD BEFORE CLEANING OR DISASSEMBLING 22 8. ...
-
Ruger 77/50 - page 23
23 Before taking the gun apart, set up to do it properly . Cover the work surface with a soft cloth so that the gun finish (and sights) will not be damaged, and provide a tray into which the parts can be put as they are removed from the gun . It is preferable to carry out these procedures on a workbench or table which has a covered top. A piece of ...
-
Ruger 77/50 - page 24
c. Unscrew the bolt sleeve counterclockwise (Figure 20). d. Remove the bolt sleeve assembly . (Figure 21). 24 b. Insert the small end of breech plug wrench handle (or suitable nail) into the “disassembly hole” in the striker/cocking piece assembly to hold it in the rear position (Figure 19). NOTE: The pin should be as close as possible in size ...
-
Ruger 77/50 - page 25
25 5. TO REMOVE THE BREECH PLUG: a. Using the supplied breech plug wrench and handle, carefully unscrew (counter -clockwise) and remove the breech plug/nipple assembly from the rear end of the barrel. (See Figures 22a & 22b) It is easier to remove the breech plug from the receiver if you keep it in the breech plug wrench as shown. A UNSCREW BRE ...
-
Ruger 77/50 - page 26
6. TO REMOVE THE STOCK: (Be certain the bolt has been removed from the rifle.) a. Remove ramrod from stock. Unscrew barrel band screw and remove barrel band forward off the stock and barrel. (See Fig. 23) b. Unscrew and remove the two screws in the trigger guard counterclockwise and carefully remove trigger guard. (See Fig. 24) Note that the longer ...
-
Ruger 77/50 - page 27
27 CARE AND CLEANING BLACK POWDER FOULING The chemical compounds formed by Black Powder and Pyrodex residue and certain percussion caps are extremely corrosive; rusting will begin within a very few hours after firing, if the rifle is left uncleaned under some conditions of humidity . Fouling will also slow down or “bind up” moving parts, possib ...
-
Ruger 77/50 - page 28
Firing deposits particles of bullet lubricant and powder in the bore, chamber , bolt, receiver , and other parts of the rifle. There is no fixed rule as to how frequently the cleaning should be carried out, but the alert gun owner soon learns that any firearm functions most reliably and accurately when it is free of accumulations of grease and othe ...
-
Ruger 77/50 - page 29
Firing a rifle with oil, grease, a bullet, or any other material even partially obstructing the bore may result in damage to the rifle and serious injury to the shooter and those nearby . Do not spray or apply lubricants directly on black powder . If the powder charge is affected by the lubricant, it may not be ignited, but the energy from the perc ...
-
Ruger 77/50 - page 30
30 Never place or store any firearm in such a manner that it may be dislodged. Firearms should always be stored securely and unloaded, away from children and careless adults. STORE SECUREL Y & UNLOADED ! W ARNING – STORAGE The rifle’ s internal mechanism can be lubricated without disassembly . A very few drops of light oil recommended as su ...
-
Ruger 77/50 - page 31
31 3. T o replace the trigger: a. Rotate safety to “fire” position. b. Place the trigger/sear spring over the dimple in the trigger . c. Assemble the trigger while aligning the spring with the dimple on the sear . d. While holding the trigger in position, replace the trigger pivot pin. 4. T o replace the breech plug: a. Lubricate the br eech pl ...
-
Ruger 77/50 - page 32
5. T o replace the barrel/receiver assembly into the stock: (Caution: Be certain that the pivot pins are not protruding from either side of the receiver .) a. Carefully install the barrel/receiver assembly into the stock, making sure the barrel/receiver assembly is in the most rearward position. (See Figure 29) b. Install the trigger guard and scre ...
-
Ruger 77/50 - page 33
c. Slide barrel band over barrel and rearward onto the stock forend. T ighten band screw when in place. Replace ramrod in stock through thimble under barrel. (See Figures 31a, 31b, & 31c) Ramrod head should rest in barrel cut beneath muzzle. Ramrod will not enter stock easily if band screw is tightened excessively . 6. T o assemble the bolt: a. ...
-
Ruger 77/50 - page 34
34 c. Carefully rotate counterclockwise until cocking piece snaps into small notch and no fur ther! Only when the bolt is correctly assembled should it be inserted into the receiver . (See Fig. 34) d. With safety in “load/unload” (middle) position, insert the bolt into the receiver . (See Fig. 35) REGARDING ACCURACY The accuracy of any muzzlelo ...
-
Ruger 77/50 - page 35
TO CLEAR A MALFUNCTION ( “ JAM ” ) If the rifle becomes difficult to operate, this can usually be traced to three basic causes (followed by the appropriate corrective action): 1. Accumulated black powder fouling (cease firing & clean gun). 2. Percussion cap fragments inside receiver (carefully remove). 3. Percussion caps not fully seated on ...
-
Ruger 77/50 - page 36
MAINTENANCE OF ST AINLESS STEEL COMPONENTS Firearms and components made of stainless steel are relatively more resistant to corrosion than those of blued steel. However , in the interest of proper operation and long life of a stainless steel firearm, inspect it frequently and clean, lubricate and apply an appropriate rust preventative. Sometimes su ...
-
Ruger 77/50 - page 37
7. The bottom finish of a telescopic sight mounted over the action may be damaged by hot gasses and cap fragments exiting the breech area when firing. This should not affect the scope’ s performance. Carefully clean all scope lenses of fouling when you clean your rifle. PLEASE NOTE THA T SOME ST A TES RESTRICT TELESCOPIC SIGHTS ON MUZZLELOADERS U ...
-
Ruger 77/50 - page 38
38 SER VICE AND P ARTS POLICY If you have any question with regard to the performance of your RUGER ® MODEL 77/50 rifle please write or call (603-863-3300) our Product Service Department, 411 Sunapee Street, Newport, New Hampshire 03773, fully describing all circumstances and conditions involved. If you should return your rifle to the factory for ...
-
Ruger 77/50 - page 39
It is the purchaser’ s responsibility to be absolutely certain that any parts ordered from the factory are correctly fitted and installed. Firearms are complicated mechanisms and IMPROPER FITTING OF P ARTS MA Y RESUL T IN A DANGEROUS MALFUNCTION, DAMAGE TO THE FIREARM, AND SERIOUS INJURY TO THE SHOOTER AND OTHER PERSONS. The purchaser and install ...
-
Ruger 77/50 - page 40
40 P ARTS LIST AND SUGGESTED RET AIL PRICES Design, prices and specifications subject to change without notice. SPECIFY MODEL AND CALIBER WHEN ORDERING RUGER ® MODEL 77/50 PERCUSSION RIFLE (See Exploded View on Page 42) Caliber Part Name Part No. Model .50 Blued Stainless Accessory Kit - Includes: Cleaning T ube; J29001 All Models • $ 9.75 – B ...
-
Ruger 77/50 - page 41
41 Receiver J00110 All Models • Not Offered For Sale Receiver Filler Screws, 2 Req’d, Not Illustrated C-83Black 77/50-RS, 77/50-RSO • ea. .50 – Receiver Filler Screws, 2 Req’d, Not Illustrated C-83 K77/50-RSBBZ • ea. .50 – Recoil Pad D06304 77/50-RS, K77/50-RSBBZ • 5.00 – Recoil Pad Screw , 2 Req’d. D-84 77/50-RS, K77/50-RSBBZ ? ...
-
Ruger 77/50 - page 42
42 RUGER ® 77/50 PERCUSSION RIFLE EXPLODED VIEW ...
-
Ruger 77/50 - page 43
43 THE BASIC RULES OF SAFE FIREARMS HANDLING We believe that Americans have a right to purchase and use firearms for lawful purposes. The private ownership of firearms in America is traditional, but that ownership imposes the responsibility on the gun owner to use his firearms in a way which will ensure his own safety and that of others. When firea ...
-
Ruger 77/50 - page 44
44 A safe direction must take into account the fact that a bullet may penetrate a wall, ceiling, floor , window , etc., and strike a person or damage property . Make it a habit to know exactly where the muzzle of your gun is pointing whenever you handle it, and be sure that you are always in control of the direction in which the muzzle is pointing, ...
-
Ruger 77/50 - page 45
45 5. BE SURE OF YOUR T ARGET BEFORE YOU SHOOT . Don’t shoot unless you know exactly where your bullet is going to strike. Be sure of the bullet stop behind your target, even when dry-firing with an unloaded gun. If you are in the field hunting, do not fire at a movement or noise. T ake the time to be absolutely certain of your target before you ...
-
Ruger 77/50 - page 46
46 8. DON ’ T SHOOT A T A HARD SURF ACE, OR A T W A TER. Bullets can glance off many surfaces like rocks or the surface of water and travel in unpredictable directions with considerable velocity . 9. NEVER TRANSPORT A LOADED FIREARM. Firearms should always be unloaded before being placed in a vehicle. A suitable carrying case or scabbard should b ...
-
Ruger 77/50 - page 47
A BRIEF ACCOUNT OF AN EXTRAORDINAR Y ACHIEVEMENT : RUGER FIREARMS One of the few American firearms manufacturers whose management has remained unchanged since starting in business, Sturm, Ruger & Company , Inc., had its beginning in a small machine shop occupying a rented frame building in Southport, Connecticut. In January , 1949, with an init ...
-
Ruger 77/50 - page 48
WHY NO W ARRANTY CARD HAS BEEN P ACKED WITH THIS NEW RUGER FIREARM The Magnuson-Moss Act (Public Law 93-637) does not require any seller or manufacturer of a consumer product to give a written warranty . It does provide that if a written warranty is given, it must be designated as “limited” or as “full” and sets minimum standards for a “f ...
Ruger 77/50についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもRuger 77/50の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRuger 77/50で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。