-
AMX PCS2 - page 1
instruction manual Control System Accessories PCS and PCS2 P ower Current Sensors ...
-
AMX PCS2 - page 2
AMX Limited W arranty and Disc laimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following e x ceptions: • Electroluminescent and LCD Control Pane ls are warranted for three (3) years, ex cept for the display ...
-
AMX PCS2 - page 3
T a ble of Contents i PCS and PCS2 P ower Current Sensor s T able of Contents Product Information ........ ................ ................. ................ .............. .............. ............ 1 Specifications ................................................... .......................................... .................... ... 1 Installat ...
-
AMX PCS2 - page 4
ii PCS and PCS2 P ower Current Sensors T able of Contents ...
-
AMX PCS2 - page 5
Product Information 1 PCS and PCS2 P ower Current Sensor s Pr oduct Inf ormation The Po wer Current Sensors (PCS) and Dual Po w er Current Sensors (PCS2) provide po wer current status for AMX equipment. Exam ples of such equipment are video projectors, moni tors, audio recei vers, and VCRs. The PCS and PCS2 detect th e A C current drawn by the equi ...
-
AMX PCS2 - page 6
Product Information 2 PCS and PCS2 P ower Current Sensors ...
-
AMX PCS2 - page 7
Installation 3 PCS and PCS2 P ower Current Sensor s Installation The PCS requires +12 VDC (+11 VDC to +17 VDC @ 20 mA minim um) for operation; the PCS2 is simply plu gged into a 120 V A C three-hole wall outlet t o obtain power . PCS and PCS2 Installation 1. Provide +12 VDC po wer fro m the Central Controller or external power supply , and connect ...
-
AMX PCS2 - page 8
Installation 4 PCS and PCS2 P ower Current Sensors Preparing cap tive wires Y ou will need a wire stripper and flat-blade scre wdriv er to prepare and c onnect the capti ve wires. 1. Strip 0.25 inch (6.35 mm) of insulation of f all wires. 2. Insert each wire into the appropriate openi ng on the connector acco rding to the wiring diagrams and connec ...
-
AMX PCS2 - page 9
Installation 5 PCS and PCS2 P ower Current Sensor s PCS2 to AXC-INP8 Connect the PCS2 output por ts to the AXC-INP8 input ports, as illust rated in FIG. 2. Follo w the illustration for Input 1 thr ough Input 8. Set the jumpers of the associated inputs on the AXC- INP8 to Switch mode. All Switch mo de inputs and the Card-Frame share com mon GND. PCS ...
-
AMX PCS2 - page 10
Installation 6 PCS and PCS2 P ower Current Sensors PCS to T elevision Contr ollers FIG. 5 illustrates th e connections required for th e PCS to television controllers. PCS2 to T elevision C ontrollers FIG. 6 illustrates th e connections between the PCS2 to television controllers. FIG. 5 PCS to television controllers FIG. 6 PCS2 to television contro ...
-
AMX PCS2 - page 11
Calibration 7 PCS and PCS2 P ower Current Sensor s Calibration The PCS and PCS2 work by setting a threshold. The ST ANDBY threshold is set be-tween the current draw of the O FF state and that of the ST ANDBY st ate. The ON threshold is then set between the current draw of the ST ANDBY state and the ON state. The PCS2 contains two major circuits, ea ...
-
AMX PCS2 - page 12
Calibration 8 PCS and PCS2 P ower Current Sensors If the unit has both ST ANDBY and ON states, follow these steps: 1. T urn the ST ANDBY and ON potentiom eters (PO Ts) clockwise until they stop. 2. Plug the PCS into an outlet and plug the unit (the device you are monitoring) into the PCS. This power pro vides the unit with power . Ther e are three ...
-
AMX PCS2 - page 13
Calibration 9 PCS and PCS2 P ower Current Sensor s PCS2 Calibration When extreme accurac y is required for calibration, allow the PCS2 to warm up for a minimum of 15 minutes before calibration. The following procedures are used for both circuit 1 and circuit 2. Calibrate each circuit independently . If the de vice only has an ON state, either ST AN ...
-
AMX PCS2 - page 14
Calibration 10 PCS and PCS2 P ower Current Sensors ...
-
AMX PCS2 - page 15
Operation and Programming 11 PCS and PCS2 P ower Current Sensor s Operation and Pr ogramming PCS Operation When properly calibrated, the PCS senses current le ve ls from sources that have one or two le vels of power consumption. The ST ANDBY LED is on when the following occurs: ! The PCS is sensing the lower le vel of current (as low as 30 mA, or 4 ...
-
AMX PCS2 - page 16
Operation and Programming 12 PCS and PCS2 P ower Current Sensors ! A one- or two-second delay . ! V erification of status changes. During transitions between states, the PCS may ta ke 1 to 2 seconds to stabilize and its output indication may be incorrect. F ailure to obser ve this delay may cause the Axcess , Axcent 2 , or Axcent 3 system to repeat ...
-
AMX PCS2 - page 17
Operation and Programming 13 PCS and PCS2 P ower Current Sensor s ...
-
AMX PCS2 - page 18
AMX reserves the right to alter specif ications with out noti ce at any t ime. brussels • dallas • los ang eles • mexico city • philad elphia • shanghai • singapor e • tampa • toronto* • yo rk 3000 research drive, richardson, TX 75082 USA • 469.624.8000 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 041 ...
AMX PCS2についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもAMX PCS2の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAMX PCS2で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。