Delta 31-695の取扱説明書

20ページ 0.93 mb
ダウンロード

ページに移動 of 20

Summary
  • Delta 31-695 - page 1

    INSTRUCTION MANUAL 6" Belt / 9" Disc Sander (Model 31-695) P ART NO. 902122 (0112) Copyright © 2001 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • Delta 31-695 - page 2

    2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety precaut ...

  • Delta 31-695 - page 3

    3 ADDITIONAL SAFETY RULES FOR BEL T / DISC SANDERS SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . 1. DO NOT operate your machine until it is completely assembled and installed according to the instructions. 2. IF YOU ARE NOT thoroughly ...

  • Delta 31-695 - page 4

    4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wir e and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wir e extension cords which have 3- prong gr ounding type plugs and matching r eceptacle which will accept the machine’ s ...

  • Delta 31-695 - page 5

    Use proper extension cor ds. Make sur e your extension cord is in good condition and is a 3-wir e extension cor d which has a 3-prong gr ounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the curr ent of the machine. An undersized cord will caus ...

  • Delta 31-695 - page 6

    6 UNP ACKING Y our new Belt/Disc Sander and Stand is shipped complete in one container . Carefully unpack the sander , stand, and all loose items from the shipping container . Fig. 2, illustrates the sander and its component parts. Fig. 3, illustrates the component parts of the stand. A T wo Upper Front and Rear Braces - 11-1/2" long B T wo Lo ...

  • Delta 31-695 - page 7

    7 ASSEMBL Y INSTRUCTIONS WARNING: FOR YOUR OWN SAFETY , DO NOT CONNECT THE SANDER TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE OWNERS MANUAL. ASSEMBLING ST AND IMPORT ANT : ANY LETTER DESIGNA TIONS THA T MA Y BE ST AMPED ON THE BRACES OF THE ST AND ARE FOR PRODUCTION PURPOSES ONL Y AND ARE N ...

  • Delta 31-695 - page 8

    8 Fig. 8 Fig. 9 Fig. 11 Fig. 12 ASSEMBLING BEL T AND PULLEY GUARD Assemble belt and pulley guard (A) Fig. 8, to the machine using two M6 x 55mm hex socket head screws (B), M6.4 lockwashers and M6.4 flat washers as shown. NOTE: Make certain plug (C) is installed into guard. ASSEMBLING SANDING DISC PLA TE 1. Slide sanding disc plate (A) Fig. 9, onto ...

  • Delta 31-695 - page 9

    9 Fig. 13 ASSEMBLING LOWER COVER FOR SANDING DISC Assemble lower cover (A) Fig. 13, to belt and pulley guard (B) using thr ee M4.2 x 13mm pan head scr ews (C). NOTE: MAKE SURE SANDING DISC DOES NOT CON- T ACT COVER. IF CONT ACT IS MADE, THE SANDING DISC MUST BE REPOSITIONED ON THE DISC PLA TE. Fig. 14 Fig. 15 ASSEMBLING DISC SANDER T ABLE 1. Insert ...

  • Delta 31-695 - page 10

    10 Fig. 20 LOCKING SWITCH IN THE “OFF” POSITION IMPORT ANT : When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. This can be done by grasping the switch toggle (B) and pulling it out of the switch, as shown in Fig. 20. With the switch toggle (B) removed, the switch will not operate. ...

  • Delta 31-695 - page 11

    11 Fig. 24 Fig. 25 Fig. 26 ADJUSTING SANDING ARM STOP A positive stop is provided to position the sanding arm level with the workbench when the arm is in the horizontal position. 1. DISCONNECT MACHINE FROM POWER SOURCE . 2. Place the sanding arm as far as possible in the hori- zontal position. 3. Place a level (A) on the sanding belt and check to s ...

  • Delta 31-695 - page 12

    12 ADJUSTING T ABLE SQUARE WITH SANDING DISC 1. DISCONNECT MACHINE FROM POWER SOURCE . 2. Using a combination square (C) Fig. 28, place one end of the square on the table with the other end against the sanding disc as shown in Fig. 28, and check to see if the table is 90 degrees to the disc. 3. If the table surface is not 90 degrees to the disc, lo ...

  • Delta 31-695 - page 13

    13 Fig. 32 Fig. 33 Fig. 34 Fig. 35 ACCESSOR Y MITER GAGE An accessory miter gage is available for your machine and is used with the disc table. The miter gage body (A) Fig. 32, can be tilted right or left for angle or miter sanding by loosening lock knob (B), and rotating miter gage body to the desired angle. Tighten lock knob (B). DUST SPOUT A dus ...

  • Delta 31-695 - page 14

    14 Fig. 36 Fig. 37 Fig. 38 Fig. 39 ADJUSTING DUST SHIELD If your sander is connected to a dust collection system, the sander is equipped with a manually operated dust shield (A) Fig. 36, which must be adjusted to suit the sanding operation. 1. If you are sanding with the disc, push in on dust shield (A) Fig. 36. 2. If you are sanding on the belt, p ...

  • Delta 31-695 - page 15

    15 Fig. 40 Fig. 41 Fig. 42 Fig. 43 5. Slide new 6" x 48" sanding belt (F) Fig. 43, over both sanding drums (G), making sure the belt (F) will travel in the direction of the arr ow located on the inside of the belt. 6. Re-apply belt tension by sliding tension lever (E) Fig. 42, to the left. 7. Replace support bracket, backstop and upper sa ...

  • Delta 31-695 - page 16

    16 REPLACING SANDING DISC When it becomes necessary to replace the sanding disc, pr oceed as follows: Fig. 44 1. DISCONNECT MACHINE FROM POWER SOURCE . 2. Loosen screw (A) Fig. 44, and r emove table assem- bly (B). 3. Remove three screws (C) Fig. 45, and lower cover (D). 4. Peel off old disc (E) as shown in Fig. 46. 5. Make sure the disc plate (F) ...

  • Delta 31-695 - page 17

    17 Fig. 49 SANDING INSIDE CURVES Inside curves can be sanded on the top sanding drum, as shown in Fig. 49. NOTE: Replace sanding drum guard after sanding operation is completed! Fig. 50 SANDING OUTSIDE CURVES Outside curves should be sanded on the sanding disc as shown in Fig. 50. W ARNING: AL WA YS SAND ON THE LEFT (DOWNWARD) SIDE OF THE SANDING D ...

  • Delta 31-695 - page 18

    18 T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized service station with ...

  • Delta 31-695 - page 19

    19 NOTES ...

  • Delta 31-695 - page 20

    20 NOTES ...

メーカー Delta カテゴリー Sander

Delta 31-695のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 31-695の取扱説明書
- Deltaの製品カード
- パンフレット
- またはDelta 31-695の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Delta 31-695の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Delta 31-695の取り付け説明書、サービスマニュアル、簡易説明書、またはDelta 31-695のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Delta 31-695の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Delta 31-695デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDelta 31-695を使用するのを助ける技術的文書のことです。説明書は通常、全てのDelta 31-695ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Deltaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Delta 31-695の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDelta 31-695の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Delta 31-695に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Delta 31-695デバイスの基本機能を使うにあたってのヒント。 Delta 31-695のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Delta 31-695に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDelta 31-695のメーカー/サービスへの連絡先に関する情報。

Delta 31-695についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDelta 31-695の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta 31-695で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)