Audiovox AXT-120の取扱説明書

12ページ 0.27 mb
ダウンロード

ページに移動 of 12

Summary
  • Audiovox AXT-120 - page 1

    Model AXT -120 120 Watt 2-Channel Amplifier OWNER'S MANUAL ...

  • Audiovox AXT-120 - page 2

    Specifications........................................................................... 1 Precautions.............................................................................. 2 Installation Instructions............................................................ 3 Wiring Instructions........................................................... ...

  • Audiovox AXT-120 - page 3

    Input Sensitivity: Low-level 200 mV. - 2 V . High-level 2V - 10 V. Supply Voltage: 12 volts, negative ground Fuse Rating: 5 amps. Dimensions (W X H X D): 8-5/8" X 2-1/8" X 3-15/16” 219 mm X 54.3 mm X 100 mm Maximum Output Power: 120 Watts 30 watts RMS @ 4 Ohms Output Impedance: 4-8 Ohms Frequency Response: 20- 25,000Hz +/-1 dB Channel S ...

  • Audiovox AXT-120 - page 4

    1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive( ) terminal of the battery. Connect this wire only after having c ...

  • Audiovox AXT-120 - page 5

    -3- 1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode. 2. Place the amplifier on the mounting surface and mark the locations of the four mounting holes as shown in the illus ...

  • Audiovox AXT-120 - page 6

    The wiring of your amplifier will depend on the system and speakers you are using but will either be a 4-Channel, 3-channel, 2-channel, or mixed-mono application. The following pages illustrate the input and output wiring for these types. Please refer to the appropriate diagrams for the system configuration you are using. The power and speaker wire ...

  • Audiovox AXT-120 - page 7

    4. Speaker Connections Depending on the type and number of speakers used with the amplifier , wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20 gauge. For leads in excess of 10 feet, #16 gauge is recommended. When wirin ...

  • Audiovox AXT-120 - page 8

    -6- INPUT WIRING DIAGRAM IMPORT ANT USE EITHER HIGH-LEVEL OR LOW -LEVEL INPUT , NOT BO TH. CAR STEREO HIGH-LEVEL (SPEAKER) INPUT (WIRE SIDE VIEW) LOW -LEVEL INPUT RCA TYPE SHIELDED EXTENSION CABLES (NOT INCLU DED) 1 2 Gray Brown Black Green White HI-INPUT HI-INPUT GND GND L + L + R + R + L L R R MIN MIN MAX MAX GAIN GAIN R R L L PWR PWR Left Right ...

  • Audiovox AXT-120 - page 9

    -7- LEFT SPEAKER CAR STEREO GROUND FUSE FUSE REM BATT GND LEFT RIGHT BATTERY FOR 12 VOL T USE ONLY AUTO-ANTENNA LEAD USE # 16 GAUGE WIRE RIGHT SPEAKER 3 GROUND MET AL SECTION OF VEHICLE EXISTING SCREW OR BOL T CLEAN PAINT , RUST , DIRT OR GREASE FROM AREA FOR GOOD CONNECTION. OUTPUT WIRING DIAGRAM WARNING! NEVER COMBINE (BRIDGE ) OUTPUTS FOR USE WI ...

  • Audiovox AXT-120 - page 10

    -8- Power Indicator Lamps The Power Indicator Lamps will light to indicate that the unit is connected to the battery and that the Remote Turn-On terminal is receiving +12 volts, thus turning on the amplifier . After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system w ...

  • Audiovox AXT-120 - page 11

    AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (a ...

  • Audiovox AXT-120 - page 12

    2003 Audiovox Electronics Corporation, Hauppauge, N.Y . C C 128-6564 Printed in Korea ...

メーカー Audiovox カテゴリー Car Amplifier

Audiovox AXT-120のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- AXT-120の取扱説明書
- Audiovoxの製品カード
- パンフレット
- またはAudiovox AXT-120の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Audiovox AXT-120の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Audiovox AXT-120の取り付け説明書、サービスマニュアル、簡易説明書、またはAudiovox AXT-120のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Audiovox AXT-120の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Audiovox AXT-120デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAudiovox AXT-120を使用するのを助ける技術的文書のことです。説明書は通常、全てのAudiovox AXT-120ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Audiovoxの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Audiovox AXT-120の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAudiovox AXT-120の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Audiovox AXT-120に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Audiovox AXT-120デバイスの基本機能を使うにあたってのヒント。 Audiovox AXT-120のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Audiovox AXT-120に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAudiovox AXT-120のメーカー/サービスへの連絡先に関する情報。

Audiovox AXT-120についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAudiovox AXT-120の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAudiovox AXT-120で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)