Porter-Cable 3802の取扱説明書

21ページ 1.05 mb
ダウンロード

ページに移動 of 21

Summary
  • Porter-Cable 3802 - page 1

    ESP AÑOL: PÁGINA 21 FRANÇAISE : P AGE 41 12" Compound Miter Saw Instruction Manual Part No. 900988 - 11-30-00 The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. _____________________________________ T ype ___________________________ ...

  • Porter-Cable 3802 - page 2

    IMPORT ANT SAFETY INSTRUCTIONS SA VE THESE INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS. This tool was designed for certain applications.DO NOT modify or use it for any application other than for which it was designed. If you have any questions relative to its application do not use the tool until you have written Porter -Cable and we have advised ...

  • Porter-Cable 3802 - page 3

    3 25. WARNING: SOME DUST CREA TED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer , birth defects or other repr oductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry pr oducts, and ...

  • Porter-Cable 3802 - page 4

    4 4 REPLACEMENT P AR TS When servicing, use only identical replacement parts. POLARIZED PLUGS: T o r educe the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way . If the plug does not fit fully in the outlet, reverse the plug. If it still does not f ...

  • Porter-Cable 3802 - page 5

    UNP ACKING 1. Car efully remove the machine fr om the carton. Retain all packing materials until you have inspected and satisfactorily operated the machine. WARNING: Do not connect the machine to the power source until you have r ead and understood this entire instruction manual. 2. Place the machine on a firm, level surface with extra room for han ...

  • Porter-Cable 3802 - page 6

    6 6 MOVING T ABLE TO THE 0 DEGREE CUT -OFF POSITION 1. Rotate locking knob (A) Fig. 6, counter -clockwise as far as it will go to unlock. Depr ess lever (B) and rotate table (C) to the 0 degree straight cut-of f position, release lever (B) and tighten locking knob (A). 2. Fig. 7, illustrates the table (C) in the 0 degree straight cut-of f position. ...

  • Porter-Cable 3802 - page 7

    7 7 3. Use a straight edge (C) Fig. 7C, to make the extension table (B) even with saw table (D), and tighten the two screws (A) Fig. 7B. 4. Attach the fence slide support (E) Fig. 7D, to the extension table (B) by using the two 1 1/4” long hex head screws, 5/16” lockwashers and 5/16” flat washers (F). Bring scr ews up through the two holes (G ...

  • Porter-Cable 3802 - page 8

    9. Position lock handle (M) Fig. 7J, on stud and replace scr ew and spring (L) that were removed in STEP 7 . NOTE: Lock handle (M) is spring-loaded and can be repositioned by lifting up on handle. A TT ACHING DUST BAG Depress spring clips (A) Fig. 8, of dust bag (B) and clip dust bag (B) onto end of dust chute. F ASTENING MACHINE TO SUPPORTING SURF ...

  • Porter-Cable 3802 - page 9

    9 9 DANGER: A TURNING SAW BLADE CAN BE DANGEROUS. AFTER COMPLETING CUT , RELEASE SWITCH TRIGGER (A) FIG. 12, TO ACTIV A TE BLADE BRAKE. KEEP CUTTINGHEAD DOWN UNTIL BLADE HAS COME TO A COMPLETE STOP . WARNING: THE TORQUE DEVELOPED DURING BRAKING MA Y LOOSEN THE ARBOR SCREW . THE ARBOR SCREW SHOULD BE CHECKED PERIODICALL Y AND TIGHTENED IF NECESSAR Y ...

  • Porter-Cable 3802 - page 10

    10 10 T o adjust the sliding fit between the movable table and the base, turn nut (A) Fig. 14, clockwise to increase the sliding fit (opposite to decrease the fit). This adjustment should not be so tight that it restricts the r otating movement of the table, or so loose that it affects the accuracy of the saw . ADJUSTING FENCE 90 DEGREES TO BLADE I ...

  • Porter-Cable 3802 - page 11

    11 11 A TT ACHING OPTIONAL WORK CLAMP The work clamp is an important accessory . After purchase, the work clamp can be attached to any one of the four holes (A) Fig. 18, provided on the base of the machine, (three of which ar e shown). 1. Thread lock knob (B) Fig. 19, into thr eaded hole where the clamp will be inserted. Place post (C) of work clam ...

  • Porter-Cable 3802 - page 12

    12 1. The cuttinghead of your compound miter saw can be tilted to cut any bevel angle from a 90 degr ee straight cut-off to a 45 degr ee left bevel angle by loosening bevel lock handle (A) Fig. 23, tilting cuttinghead (B) to the desired angle, and tightening lock handle (A). 2. Positive stops are pr ovided to rapidly position the saw blade at 90 an ...

  • Porter-Cable 3802 - page 13

    13 13 ADJUSTING 0 AND 45 DEGREE BEVEL POSITIVE STOPS 1. DISCONNECT THE SAW FROM THE POWER SOURCE. 2. Adjust saw so that both bevel and miter pointers are set at 0 degrees. Tighten bevel lock handle and lock cuttinghead in down position. 3. Place one end of a square (A) Fig. 27 on the table and the other end against the blade. The blade should be se ...

  • Porter-Cable 3802 - page 14

    14 14 Correct adjustment pr ovides for a good snug sliding fit between these two parts. This adjustment should not be so tight that it restricts the tilting movement of the trunnion (A) when bevel cutting, or so loose that it af fects the accuracy of the saw cut. ADJUSTING THE TENSION OF CUTTINGHEAD RETURN SPRING The tension of the cuttinghead retu ...

  • Porter-Cable 3802 - page 15

    15 15 TYPICAL OPERA TIONS AND HELPFUL HINTS 1. Before cutting, make certain the cutting arm and table area ar e at their correct settings and firmly locked in place. 2. Before cutting, determine that the workpiece is the right size for the saw . 3. Place the workpiece on the table and hold or clamp it firmly against the fence. Fig. 35 illustrates t ...

  • Porter-Cable 3802 - page 16

    16 16 CUTTING BOWED MA TERIAL 1. When cutting flat pieces, first check to see if the material is bowed. If it is, make sure the material is positioned on the table as shown in Fig. 39. 2. If the material is positioned the wrong way , as shown in Fig. 40, the workpiece will pinch the blade near the completion of the cut. CONSTRUCTING WORK SUPPORT EX ...

  • Porter-Cable 3802 - page 17

    17 17 CUTTING CROWN MOULDING One of the many features of the saw is the ease of cutting crown moulding. The following is an example of cutting both inside and outside corners on 52/38 degree wall angle crown moulding. NOTE: The following procedur e for inside or outside crown molding corners is the same with the exception that the bevel position wi ...

  • Porter-Cable 3802 - page 18

    18 18 MAINTENANCE CHANGING THE BLADE WARNING: USE ONL Y CROSS-CUTTING SAW BLADES. DO NOT USE BLADES WITH DEEP GULLETS AS THEY CAN DEFLECT AND CONT ACT GUARD 1. Use only 12" diameter blades with 1" arbor holes that are rated for 4200 RPM or higher . 2. DISCONNECT MACHINE FROM THE POWER SOURCE. 3. Loosen screw (A) Fig. 46, with wr ench (B) ...

  • Porter-Cable 3802 - page 19

    19 19 BRUSH INSPECTION AND REPLACEMENT CAUTION: BEFORE INSPECTING BRUSHES, DISCONNECT THE MACHINE FROM THE POWER SOURCE. Brush life varies, depends on the load on the motor . Check the brushes after the first 50 hours of use of a new machine, or after a new set of brushes has been installed. After the first check, examine them after about 10 hours ...

  • Porter-Cable 3802 - page 20

    20 20 NOTES ...

  • Porter-Cable 3802 - page 21

    The following are trademarks of POR TER-CABLE Corporation (Las siguientes son marcas registradas de POR TER-CABLE S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE Corporation): BAMMER ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORT A-BAND ® , PORT A-PLANE ® , PORTER- CABLE ® , QUICKSAND ® , SANDTRAP ® , S ...

メーカー Porter-Cable カテゴリー Saw

Porter-Cable 3802のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 3802の取扱説明書
- Porter-Cableの製品カード
- パンフレット
- またはPorter-Cable 3802の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Porter-Cable 3802の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Porter-Cable 3802の取り付け説明書、サービスマニュアル、簡易説明書、またはPorter-Cable 3802のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Porter-Cable 3802の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Porter-Cable 3802デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPorter-Cable 3802を使用するのを助ける技術的文書のことです。説明書は通常、全てのPorter-Cable 3802ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Porter-Cableの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Porter-Cable 3802の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPorter-Cable 3802の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Porter-Cable 3802に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Porter-Cable 3802デバイスの基本機能を使うにあたってのヒント。 Porter-Cable 3802のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Porter-Cable 3802に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPorter-Cable 3802のメーカー/サービスへの連絡先に関する情報。

Porter-Cable 3802についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPorter-Cable 3802の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPorter-Cable 3802で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)