Bretford LAP30EBAの取扱説明書

33ページ 4.44 mb
ダウンロード

ページに移動 of 33

Summary
  • Bretford LAP30EBA - page 1

    LAP30EBA LAP30EFR NOTEBOOK CART ASSEMBL Y Assembly Instructions for: INTERIOR E-UNIT REPOSITIONING / REPLACEMENT AND TIMER INST ALLA TION Parts List Q t y . Part No. Description 1 LAP30EBA Cart Assembly , e-units at back LAP30EFR Ca rt Assembly , e-units at front T ools Required Philips screwdriver Step 1 Open both front doors of cart to access E-U ...

  • Bretford LAP30EBA - page 2

    clip DET A I L 'A' DET A I L 'B ' E-Unit power cord bracket assembly bottom shelf Front View bracket assembly bracket assembly ...

  • Bretford LAP30EBA - page 3

    Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Step 3 Remove 18 screws (2 per shelf) from r ...

  • Bretford LAP30EBA - page 4

    DET A I L 'D ' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out. Set each shelf aside. mounting tab ...

  • Bretford LAP30EBA - page 5

    clip-rear Step 5 cutout window Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to opposite corner of cart. 3. T ilt in and set bottom in back, in front of rear p anel cutout window . 4. Grip the top and tilt to the upright position, underneath t ...

  • Bretford LAP30EBA - page 6

    Step 6 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AI L 'E' Step 7 Reinstall 18 ...

  • Bretford LAP30EBA - page 7

    Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DET AIL 'A'). DET A I L 'A ' E-UNIT REPOSITIONING: 'REAR TO FRONT' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING DET A I L 'B' mounting tab ...

  • Bretford LAP30EBA - page 8

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord bracket assembly Front View Unwind the power cord of the E-Units from the cord wrap brackets (on the rer panel). Loosen the screw ...

  • Bretford LAP30EBA - page 9

    clip-rear DET A I L 'C ' DET A I L 'D ' Step 3 Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. ...

  • Bretford LAP30EBA - page 10

    Step 4 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET A I L 'F' Step 5 Reinstall 18 ...

  • Bretford LAP30EBA - page 11

    Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Position to the front of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position. When repositioned correctly , the E-Unit power switch should ...

  • Bretford LAP30EBA - page 12

    E-UNIT REPLACEMENT : 'REAR LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DET AI L 'A'). DET A I L 'B ' mounting tab DET A I L 'A ' ...

  • Bretford LAP30EBA - page 13

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord bracket assembly Front View Unwind the power cord of the E-Units from the cord wrap brackets (on the rer panel). Loosen the screw ...

  • Bretford LAP30EBA - page 14

    clip-rear DET A I L 'C ' DET A I L 'D ' Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. ...

  • Bretford LAP30EBA - page 15

    Step 4 clip-rear Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should be visible from rear panel cutout window . Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot ...

  • Bretford LAP30EBA - page 16

    Step 5 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AI L 'E' Step 6 Reinstall 18 ...

  • Bretford LAP30EBA - page 17

    Step 1 E-UNIT REPLACEMENT : 'FRONT LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING SEE DET AIL 'A' SEE DET AIL 'B' bottom shelf E-Unit power cord bracket assembly bottom shelf Front View Open both front doors of cart to access E-Unit(s). Unwind any length of E-Unit power cord remaining on t ...

  • Bretford LAP30EBA - page 18

    Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. clip DET A I L 'A' DET A I L 'B ' bracket assembly bracket assembly front-right front-left ...

  • Bretford LAP30EBA - page 19

    front-right front-left Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first against the offset and tilting it in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with ...

  • Bretford LAP30EBA - page 20

    TIMER REPLACEMENT : 'E-UNIT A T REAR LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING DET A I L 'A ' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET A IL 'A'). DET A I L 'B ' mounting tab ...

  • Bretford LAP30EBA - page 21

    Step 2 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. Step 3 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove bracket assembly . The E- Unit bracket assembly ...

  • Bretford LAP30EBA - page 22

    Step 4 Remove filler bracket from bracket by pulling upward. Discard filler bracket. filler bracket bracket Step 5 Install timer with 2 screws. Adjust timer dial to current time. ...

  • Bretford LAP30EBA - page 23

    Step 7 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf. notch tab Step 6 bottom flange- timer/bracket ...

  • Bretford LAP30EBA - page 24

    DET A I L 'C ' Step 8 Reinstall 6 screws to rear panel that will secure the 3 interior shelves (see DET AIL 'C'). DO NOT OVER TIGHTEN SCREWS . Installation is now complete and ready for use. Adjust timer to current time when installation is complete and ready to be plugged back into power source. If necessary , adjust tabs for c ...

  • Bretford LAP30EBA - page 25

    TIMER INST ALLA TION: 'E-UNIT A T FRONT LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING Step 1 SEE DET AIL 'A' SEE DET AIL 'B' bottom shelf clip DET A I L 'A ' DET A I L 'B' bracket assembly bracket assembly Please read and follow all instructions thoroughly. Bretford wi ...

  • Bretford LAP30EBA - page 26

    Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. front-right front-left DET A I L 'A &ap ...

  • Bretford LAP30EBA - page 27

    Step 4 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. DET A I L 'B' mounting tab ...

  • Bretford LAP30EBA - page 28

    Step 5 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove bracket assembly . bottom flange- bracket assembly Step 6 Remove filler bracket from bracket by pulling upward. Discard filler bracket. filler bracket bracket ...

  • Bretford LAP30EBA - page 29

    Step 7 Install replacement timer with 2 screws. Adjust timer dial to current time. Step 8 Install timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole shown. Make sure timer face is aligned with rear panel cutouts. Tighten screws. bottom flange- timer/bracket hole location ...

  • Bretford LAP30EBA - page 30

    notch tab Step 9 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf. DET A I L 'C ' Step 10 Rei ...

  • Bretford LAP30EBA - page 31

    Step 1 1 bottom shelf front-right front-left Carefully reinstall E-Units into position by placing bottom in first against the offset and tilting it in sideways to the top (underneath the channel bracket of the cart top panel). When repositioned correctly , the E-Units power switch should face the front and the full row of outlets should face the do ...

  • Bretford LAP30EBA - page 32

            $8;  $8;           $8;   $8;            $8; $8; LABEL INST ALLA TION: E-Unit at front suggested label direction suggested installation ...

  • Bretford LAP30EBA - page 33

    Part #031-6609 Rev . 08.29.05 CH Bretford 1 1000 Seymour Avenue Franklin Park, IL 60131 TEL: 847.678.2545 800.521.9614 FAX: 847.678.0852 800.343.1779 P AD LOCK - DOOR: www.bretford.com Bretford Ltd. 2 Etongate 1 10 Winsor Road, Slough Berkshire SL1 2JA England TEL: 01753 539955 FAX: 01753 539478 Open Lock The First T ime 1) Set the combination to 0 ...

メーカー Bretford カテゴリー Outdoor Cart

Bretford LAP30EBAのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- LAP30EBAの取扱説明書
- Bretfordの製品カード
- パンフレット
- またはBretford LAP30EBAの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bretford LAP30EBAの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bretford LAP30EBAの取り付け説明書、サービスマニュアル、簡易説明書、またはBretford LAP30EBAのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bretford LAP30EBAの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bretford LAP30EBAデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBretford LAP30EBAを使用するのを助ける技術的文書のことです。説明書は通常、全てのBretford LAP30EBAユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bretfordの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bretford LAP30EBAの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBretford LAP30EBAの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bretford LAP30EBAに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bretford LAP30EBAデバイスの基本機能を使うにあたってのヒント。 Bretford LAP30EBAのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bretford LAP30EBAに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBretford LAP30EBAのメーカー/サービスへの連絡先に関する情報。

Bretford LAP30EBAについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBretford LAP30EBAの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBretford LAP30EBAで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)