Русский dropdown-ico

Инструкция обслуживания Bretford LAP30EBA

33 страниц 4.44 mb
Скачать

Перейти на страницу of 33

Summary
  • Bretford LAP30EBA - page 1

    LAP30EBA LAP30EFR NOTEBOOK CART ASSEMBL Y Assembly Instructions for: INTERIOR E-UNIT REPOSITIONING / REPLACEMENT AND TIMER INST ALLA TION Parts List Q t y . Part No. Description 1 LAP30EBA Cart Assembly , e-units at back LAP30EFR Ca rt Assembly , e-units at front T ools Required Philips screwdriver Step 1 Open both front doors of cart to access E-U ...

  • Bretford LAP30EBA - page 2

    clip DET A I L 'A' DET A I L 'B ' E-Unit power cord bracket assembly bottom shelf Front View bracket assembly bracket assembly ...

  • Bretford LAP30EBA - page 3

    Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Step 3 Remove 18 screws (2 per shelf) from r ...

  • Bretford LAP30EBA - page 4

    DET A I L 'D ' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out. Set each shelf aside. mounting tab ...

  • Bretford LAP30EBA - page 5

    clip-rear Step 5 cutout window Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to opposite corner of cart. 3. T ilt in and set bottom in back, in front of rear p anel cutout window . 4. Grip the top and tilt to the upright position, underneath t ...

  • Bretford LAP30EBA - page 6

    Step 6 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AI L 'E' Step 7 Reinstall 18 ...

  • Bretford LAP30EBA - page 7

    Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DET AIL 'A'). DET A I L 'A ' E-UNIT REPOSITIONING: 'REAR TO FRONT' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING DET A I L 'B' mounting tab ...

  • Bretford LAP30EBA - page 8

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord bracket assembly Front View Unwind the power cord of the E-Units from the cord wrap brackets (on the rer panel). Loosen the screw ...

  • Bretford LAP30EBA - page 9

    clip-rear DET A I L 'C ' DET A I L 'D ' Step 3 Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. ...

  • Bretford LAP30EBA - page 10

    Step 4 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET A I L 'F' Step 5 Reinstall 18 ...

  • Bretford LAP30EBA - page 11

    Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Position to the front of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position. When repositioned correctly , the E-Unit power switch should ...

  • Bretford LAP30EBA - page 12

    E-UNIT REPLACEMENT : 'REAR LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DET AI L 'A'). DET A I L 'B ' mounting tab DET A I L 'A ' ...

  • Bretford LAP30EBA - page 13

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord bracket assembly Front View Unwind the power cord of the E-Units from the cord wrap brackets (on the rer panel). Loosen the screw ...

  • Bretford LAP30EBA - page 14

    clip-rear DET A I L 'C ' DET A I L 'D ' Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. ...

  • Bretford LAP30EBA - page 15

    Step 4 clip-rear Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should be visible from rear panel cutout window . Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot ...

  • Bretford LAP30EBA - page 16

    Step 5 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET AI L 'E' Step 6 Reinstall 18 ...

  • Bretford LAP30EBA - page 17

    Step 1 E-UNIT REPLACEMENT : 'FRONT LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING SEE DET AIL 'A' SEE DET AIL 'B' bottom shelf E-Unit power cord bracket assembly bottom shelf Front View Open both front doors of cart to access E-Unit(s). Unwind any length of E-Unit power cord remaining on t ...

  • Bretford LAP30EBA - page 18

    Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. clip DET A I L 'A' DET A I L 'B ' bracket assembly bracket assembly front-right front-left ...

  • Bretford LAP30EBA - page 19

    front-right front-left Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first against the offset and tilting it in sideways to the top. When repositioned correctly , the E-Unit(s) power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with ...

  • Bretford LAP30EBA - page 20

    TIMER REPLACEMENT : 'E-UNIT A T REAR LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING DET A I L 'A ' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET A IL 'A'). DET A I L 'B ' mounting tab ...

  • Bretford LAP30EBA - page 21

    Step 2 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. Step 3 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove bracket assembly . The E- Unit bracket assembly ...

  • Bretford LAP30EBA - page 22

    Step 4 Remove filler bracket from bracket by pulling upward. Discard filler bracket. filler bracket bracket Step 5 Install timer with 2 screws. Adjust timer dial to current time. ...

  • Bretford LAP30EBA - page 23

    Step 7 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf. notch tab Step 6 bottom flange- timer/bracket ...

  • Bretford LAP30EBA - page 24

    DET A I L 'C ' Step 8 Reinstall 6 screws to rear panel that will secure the 3 interior shelves (see DET AIL 'C'). DO NOT OVER TIGHTEN SCREWS . Installation is now complete and ready for use. Adjust timer to current time when installation is complete and ready to be plugged back into power source. If necessary , adjust tabs for c ...

  • Bretford LAP30EBA - page 25

    TIMER INST ALLA TION: 'E-UNIT A T FRONT LOCA TION' NOTE: UNPLUG CART POWER CORDS FROM POWER SOURCE BEFORE ST AR TING Step 1 SEE DET AIL 'A' SEE DET AIL 'B' bottom shelf clip DET A I L 'A ' DET A I L 'B' bracket assembly bracket assembly Please read and follow all instructions thoroughly. Bretford wi ...

  • Bretford LAP30EBA - page 26

    Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. front-right front-left DET A I L 'A &ap ...

  • Bretford LAP30EBA - page 27

    Step 4 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. DET A I L 'B' mounting tab ...

  • Bretford LAP30EBA - page 28

    Step 5 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove bracket assembly . bottom flange- bracket assembly Step 6 Remove filler bracket from bracket by pulling upward. Discard filler bracket. filler bracket bracket ...

  • Bretford LAP30EBA - page 29

    Step 7 Install replacement timer with 2 screws. Adjust timer dial to current time. Step 8 Install timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole shown. Make sure timer face is aligned with rear panel cutouts. Tighten screws. bottom flange- timer/bracket hole location ...

  • Bretford LAP30EBA - page 30

    notch tab Step 9 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf. DET A I L 'C ' Step 10 Rei ...

  • Bretford LAP30EBA - page 31

    Step 1 1 bottom shelf front-right front-left Carefully reinstall E-Units into position by placing bottom in first against the offset and tilting it in sideways to the top (underneath the channel bracket of the cart top panel). When repositioned correctly , the E-Units power switch should face the front and the full row of outlets should face the do ...

  • Bretford LAP30EBA - page 32

            $8;  $8;           $8;   $8;            $8; $8; LABEL INST ALLA TION: E-Unit at front suggested label direction suggested installation ...

  • Bretford LAP30EBA - page 33

    Part #031-6609 Rev . 08.29.05 CH Bretford 1 1000 Seymour Avenue Franklin Park, IL 60131 TEL: 847.678.2545 800.521.9614 FAX: 847.678.0852 800.343.1779 P AD LOCK - DOOR: www.bretford.com Bretford Ltd. 2 Etongate 1 10 Winsor Road, Slough Berkshire SL1 2JA England TEL: 01753 539955 FAX: 01753 539478 Open Lock The First T ime 1) Set the combination to 0 ...

Производитель Bretford Категория Outdoor Cart

Документы, которые мы получаем от производителя устройства Bretford LAP30EBA мы можем разделить на несколько групп. Это в частности:
- технические чертежи Bretford
- инструкции обслуживания LAP30EBA
- паспорта изделия Bretford
- информационные брошюры
- энергетические этикетки Bretford LAP30EBA
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Bretford LAP30EBA.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Bretford LAP30EBA, инструкции обслуживания, короткие инструкции или инструкции пользователя Bretford LAP30EBA. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Bretford LAP30EBA.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Bretford LAP30EBA, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Bretford LAP30EBA пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Bretford LAP30EBA.

Полная инструкция обслуживания Bretford, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Bretford LAP30EBA - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Bretford LAP30EBA, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Bretford LAP30EBA, которое найдем в данном документе
3. Советы по использованию основных функций устройства Bretford LAP30EBA - которые должны облегчить нам первые шаги во время использования Bretford LAP30EBA
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Bretford LAP30EBA
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Bretford LAP30EBA в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Bretford LAP30EBA?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Bretford LAP30EBA, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Bretford LAP30EBA со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Captcha
Новая картинка

Комментарии (0)