-
KitchenAid KCDP 9010/I - page 1
KCDP 9010/I Instructions for use ...
-
KitchenAid KCDP 9010/I - page 2
...
-
KitchenAid KCDP 9010/I - page 3
W arnings 4 Safeguarding the environment 5 Instructions for installation and use 6 Extraction Modes 6 Installation 7 Hood description 11 Functioning 11 Maintenance 12 After-Sales Service 14 ...
-
KitchenAid KCDP 9010/I - page 4
• This appliance should not be used by children or people with limited physical or mental abilities and with no experience or knowledge of its use, unless they are supervised by someone in charge of their safety or who has taught them how to use the appliance. • Children should not play with the appliance. 1. Do not connect the appliance to the ...
-
KitchenAid KCDP 9010/I - page 5
5 1. P acking The packaging material is entirely recyclable and marked with the recycling symbol . Follow local regulations for scrapping. Keep the packaging materials (plastic bags, polystyrene parts, etc.) out of reach of children, as they are potentially dangerous. 2. Product This appliance is marked according to the European Directive 2002/96/E ...
-
KitchenAid KCDP 9010/I - page 6
This is an excessively heavy product and the movement and installation of the hood should be done by at least two or more people. Follow the instructions in this manual carefully . All responsibility is denied for problems, damage or fire to the appliance resulting in failure to comply with the instructions in this manual. Instructions for installa ...
-
KitchenAid KCDP 9010/I - page 7
ceiling wall side cabinet V enting exhaust pipe passages and side cabinet min. width of hood centre line Cooking surface * Recirculation mode only all measurements in mm The hood comes with plugs suitable for most walls/ceilings. Y ou should however consult a qualified technician to make sure the installation is suitable for your kind of wall/ceili ...
-
KitchenAid KCDP 9010/I - page 8
centre line support bracket hooks bottom fastener locations Ø 8 mm REAR VIEW hooks bottom screw hole (inside the canopy) FRONT VIEW Fig. 4 • Place the lower support bracket on the perforation layout aligning it with the sketched rectangle. Mark the two external holes, then drill the holes. Remove the perforation layout and insert 2 wall plugs an ...
-
KitchenAid KCDP 9010/I - page 9
• The hood has two identical brackets for attaching the chimney . Attach the first bracket ( G – the side with fixing holes facing upwards – see Fig. 6 ) to the wall next to the ceiling, using the support bracket as a template (the small slots cut in the bracket should coincide with the centre lines previously traced on the wall), mark 2 hole ...
-
KitchenAid KCDP 9010/I - page 10
10 • Hook the hood onto the lower bracket. • Fit the hood securely to the wall with screws • Connect the venting pipe (V enting pipe and straps are not provided and must be purchased seperately) to the connection ring found above the motor suction unit. The other end of the pipe should be attached to venting pipe leading to the outside if you ...
-
KitchenAid KCDP 9010/I - page 11
T urn to maximum speed when there is a lot of steam in the kitchen. W e would advise you to turn the extraction on 5 minutes before starting to cook and leave it running after you have finished cooking for about another 15 minutes. 1. ON/OFF light button: press once for a dimmed light, twice for a full light. P ress again to turn off 2. Motor ON/OF ...
-
KitchenAid KCDP 9010/I - page 12
12 Always disconnect the power supply before carrying out any kind of maintenance work. Cleaning The hood should be cleaned regularly both inside and out (at least as often as you carry out maintenance on the grease filters). Use a damp cloth with mild cleaning products. Avoid using harsh products. DO NOT USE ALCOHOL! W arning: Failure to follow th ...
-
KitchenAid KCDP 9010/I - page 13
13 Carbon filter (only in recirculation mode) Fig. 12 The Carbon filter absorbs any unpleasant smells produced when cooking. The carbon filter can be washed every two months in hot water with suitable cleaning fluids, or in the dishwasher at 65°C (when washing in the dishwasher , do a full wash without any plates inside). Shake off any excess wate ...
-
KitchenAid KCDP 9010/I - page 14
Before calling Customer Care Centre: 1. See if you can solve the problem yourself with the help of the “T roubleshooting guide”. 2. Switch off the hood for a few minutes and re- start it to see if the problem has cleared itself . 3. If the malfunction persists, call the Customer Care Centre Service. Specify: • the nature of the problem, • t ...
-
KitchenAid KCDP 9010/I - page 15
15 W arning - this appliance must be earthed Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T .A. approved fuse to BS 1362 type and proceed as follows: 1. Remove the fuse cover ( A ) and fuse ( B ). 2. Fit replacement 13A fuse into fuse cover . 3. Ref ...
-
KitchenAid KCDP 9010/I - page 16
5019 718 02007 Printed in Italy n 05/07 GB ...
KitchenAid KCDP 9010/Iについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもKitchenAid KCDP 9010/Iの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKitchenAid KCDP 9010/Iで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。