Bryant TSTATBBNQ001の取扱説明書

24ページ 0.56 mb
ダウンロード

ページに移動 of 24

Summary
  • Bryant TSTATBBNQ001 - page 1

    72 Battery Operated 4-Wire Operation Millivolt Compatible Digital Display DC V oltage Comp atible S tage: 1-Heat, 1-Cool Easy Slide Switch Operation USERS INFORMA TION MANUAL MODEL TST ATBBNQ001 NON-PROGRAMMABLE DIGIT AL THERMOST AT NOTE TO INST ALLER: This manual must be left with the equipment user . Heating & Cooling Systems Heat Cool Thermo ...

  • Bryant TSTATBBNQ001 - page 2

    P age 1 Ta ble Of Content s LOCA TION OF CONTROLS DISPLAY NORMAL OPERA TION PREP ARA TION REMOVE OLD THERMOSTA T WIRE CONNECTIONS JUMPER CONFIGURA TION TEST OPERA TION TROUBLESHOOTING W ARRANTY 2 4 5 6 7 10 17 20 21 INSTA LLA TION AND BA TTER Y REPLACEMENT 8 24 Bryant Heating & Cooling Systems Patents Pending 4/03 ...

  • Bryant TSTATBBNQ001 - page 3

    TST A TBBNQ001 Safety W arnings P age 2 CAUTION Follow Installation Instructions carefully . DISCONNECT POWER T O THE HEA TER - AIR CONDITIONER BEFORE REMOVING THE OLD THERMOST A T AND INST ALLING THE NEW THERMOST A T . W ARNING The 2 Alkaline “AA” batteries must be replaced at least every 12 months to assure proper operation. The thermostat wi ...

  • Bryant TSTATBBNQ001 - page 4

    Location of Controls P age 3 MODE SWITCH Heat, Cool or Off On or Auto FAN SWIT CH UP & DOWN BUTTONS 72 ...

  • Bryant TSTATBBNQ001 - page 5

    Display P age 4 Current room temperature. If the Up or Down arrow buttons are pressed the thermostat will show the desired Set T emp temperature indicator . Once this screen is reached you may use the Up or Down arrow buttons to adjust the desired room temperature. After five seconds with no button presses the thermostat will revert back to show th ...

  • Bryant TSTATBBNQ001 - page 6

    P age 5 Normal Operation Manual Operation Select heat or cool with the mode switch. Normally leave the fan switched to auto. In fan auto, the fan will turn on only with a heat or cool demand. When Fan On is selected, the fan will run continuously , even when the mode switch is set to Off . Adjust the desired set temperature with the Up or Down butt ...

  • Bryant TSTATBBNQ001 - page 7

    Step #1 Prep aration P age 6 These tools will be required: Flat Blade Screwdriver Wire cutter & S tripper Make sure your Heater/Air Conditioner is working properly before beginning installation of the thermost at. Carefully unpack the thermost at. Save the screws and instructions. T urn off the power to the Heating/Air Conditioning system at th ...

  • Bryant TSTATBBNQ001 - page 8

    P age 7 Step #2 Remove & Replace Old Thermost at Remove the cover of the old thermostat. If it does not come off easily check for screws. Loosen the screws holding the thermostat base or subbase to the wall, and lift away . Disconnect the wires from the old thermostat. T ape the ends of the wires as you disconnect them, and mark them with the l ...

  • Bryant TSTATBBNQ001 - page 9

    P age 8 The top of the thermostat housing has two (2) screw- driver slots to assist when seperating. Repeat the procedure in the other screw driver slot. Separate the housing halves by pulling the top forward until the pins release, and then lift the bottom out. SCREWDRIVER SLOTS The batteries must be replaced immediately when the thermostat displa ...

  • Bryant TSTATBBNQ001 - page 10

    P age 9 Battery Replacement REPLACE WITH A LKALINE BA TTERIES A T LEAST ONCE EVER Y YEAR, OR WHEN THE “LOW BA TTER Y” ICON APPEARS (pages 2,8). USE “ AA ” SIZE ALKALINE BA TTERIES USE “ AA ” SIZE ALKALINE BA TTERIES POSITION BA TTERIES A S SHOWN FAN W/ HEA T HEA T PUMP 1 2 3 1 2 3 J1 J2 ...

  • Bryant TSTATBBNQ001 - page 11

    72 Heat Off Cool Fan On FanA uto If the terminal designations on your old thermostat do not match those on the new thermostat, refer to the chart below , or the wiring diagrams that follow . Wire from the old thermostat terminal marked Function Install on the new thermostat connector marked Y1 or Y Cooling Y Power Rh, R, M, V r , A R B B Rev . V al ...

  • Bryant TSTATBBNQ001 - page 12

    Sample Wiring Diagrams FA N COOLING POWER W G R Y W Y B O G R 4 Wire, 1 St age Cooling, 1 Stage Gas Heat Residential Gas or Electric Heat * , Electric Cool, split systems & package units P age 11 GAS OR ELECTRIC HEA T 4 Conductor 18 to 22 gauge unshielded cable from the thermostat to the equipment. ...

  • Bryant TSTATBBNQ001 - page 13

    P age 12 Sample Wiring Diagrams 4 Wire, 1 St age Cooling, 1 Stage Heat-Heat Pump with O reversing valve*. Residential Heat Pumps, split systems & package units, with no auxiliary heat. FA N POWER G R COMPRESSOR Y W Y B O G R REVERSING V AL VE O * For Heat Pump or Electric Heat applications see page 17 or 18 for Jumper configuration. 4 Conductor ...

  • Bryant TSTATBBNQ001 - page 14

    P age 13 Sample Wiring Diagrams 4 Wire, 1 St age Cooling, 1 Stage Heat-Heat Pump with B reversing valve*. Residential Heat Pumps, split systems & package units, with no auxiliary heat. FA N POWER G R COMPRESSOR Y W Y B O G R REVERSING V AL VE B * For Heat Pump or Electric Heat applications see page 17 or 18 for Jumper configuration. 4 Conductor ...

  • Bryant TSTATBBNQ001 - page 15

    P age 14 Sample Wiring Diagrams FA N POWER G R W W Y B O G R 3 Wire, 1 St age Heat Residential Gas or Electric Heat units with a separately controlled fan. GAS OR ELECTRIC HEA T 3 Conductor 18 to 22 gauge unshielded cable from the thermostat to the equipment. ...

  • Bryant TSTATBBNQ001 - page 16

    P age 15 Sample Wiring Diagrams POWER W R W Y B O G R 2 Wire, 1 St age Gas Heat Residential Gas or Millivolt units. GAS OR ELECTRIC HEA T 2 Conductor 18 to 22 gauge unshielded cable from the thermostat to the equipment. ...

  • Bryant TSTATBBNQ001 - page 17

    P age 16 Sample Wiring Diagrams FA N COOLING POWER G R Y W Y B O G R 3 Wire, 1 St age Cooling Residential Electric Cool units 3 Conductor 18 to 22 gauge unshielded cable from the thermostat to the equipment. ...

  • Bryant TSTATBBNQ001 - page 18

    P age 17 Step #5 Jumper Configuration FAN W/ HEA T HEA T PUMP 1 2 3 1 2 3 J1 J2 Jumper and Jumper are shown in the factory default positions for typical gas furnace heating with electric cooling. *Outputs active - For normal operation do not connect to equipment OUTPUTS No Demand With Demand Cooling Mode Heating Mode O* Y , G , O* B* W Figure-A) 72 ...

  • Bryant TSTATBBNQ001 - page 19

    P age 18 Step #5 Jumper Configuration FAN W/ HEA T HEA T PUMP 1 2 3 1 2 3 J1 J2 Jumper is used to select Fan On (G) with Heat (W). Jumper shown in the factory default position. *Outputs active - For normal operation do not connect to equipment OUTPUTS No Demand With Demand Cooling Mode Heating Mode O* Y , G , O* B* W, G Figure-B) 72 Heat Off Cool F ...

  • Bryant TSTATBBNQ001 - page 20

    P age 19 Step #5 Jumper Configuration FAN W/ HEA T HEA T PUMP 1 2 3 1 2 3 J1 J2 Jumper and Jumper are used to select heat pump operation. Note: Thermost at Does Not Have Auxiliary Heat / Emergency Heat Capability . Leave jumpers in original factory default positions (figure-A) for non heat pump applications. Figure-C) OUTPUTS No Demand With Demand ...

  • Bryant TSTATBBNQ001 - page 21

    P age 20 Step #5 T est Operation Adjust the Slide Switch until it is located under the word HEA T on the thermostat. Press the Up or Down buttons until the set temperature is 10 degrees above room temperature. The HV AC unit should energize in the heating mode (pages 4-5). Adjust the Slide Switch until it is located under the word COOL on the therm ...

  • Bryant TSTATBBNQ001 - page 22

    P age 21 T roubleshooting SYMPTOM: The slide switches on the thermostat are very difficult to move. CAUSE: The backplate of the thermost at is deformed by being screwed tightly into a wall that is not perfectly flat. REMEDY : Loosen the screws holding the thermostat into the wall. 72 Heat Off Cool Fan On FanA uto 72 Heat Off Cool Fan On FanA uto SY ...

  • Bryant TSTATBBNQ001 - page 23

    P age 22 T roubleshooting 4Z95 72 Heat Off Cool Fan On FanA uto C c F FOR HOME OR OFFICE USE T ested to Comply with FCC S tandards Battery S tat TST A TBBNQ001 SYMPTOM: The heating does not attempt to turn on. CAUSE: The heating setpoint is set too low or the Mode Switch is not set for Heat, or the batteries are too weak. REMEDY : Consult the Norma ...

  • Bryant TSTATBBNQ001 - page 24

    THIS WARRANTY DOES NOT INCL UDE LABOR OR OTHER COSTS incurred for diagnosing, repairing, removing, installing, shipping , servicing or handling of either defective parts or replacement parts. Such costs may be covered by a separate warranty provided by the installer . THIS WARRANTY APPLIES ONL Y TO PRODUCTS IN THEIR ORIGINAL INSTALLA TION LOCA TION ...

メーカー Bryant カテゴリー Thermostat

Bryant TSTATBBNQ001のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- TSTATBBNQ001の取扱説明書
- Bryantの製品カード
- パンフレット
- またはBryant TSTATBBNQ001の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bryant TSTATBBNQ001の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bryant TSTATBBNQ001の取り付け説明書、サービスマニュアル、簡易説明書、またはBryant TSTATBBNQ001のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bryant TSTATBBNQ001の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bryant TSTATBBNQ001デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBryant TSTATBBNQ001を使用するのを助ける技術的文書のことです。説明書は通常、全てのBryant TSTATBBNQ001ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bryantの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bryant TSTATBBNQ001の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBryant TSTATBBNQ001の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bryant TSTATBBNQ001に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bryant TSTATBBNQ001デバイスの基本機能を使うにあたってのヒント。 Bryant TSTATBBNQ001のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bryant TSTATBBNQ001に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBryant TSTATBBNQ001のメーカー/サービスへの連絡先に関する情報。

Bryant TSTATBBNQ001についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBryant TSTATBBNQ001の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBryant TSTATBBNQ001で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)