-
Craftsman 315.10136 - page 1
Operator's Manual 1/2 in. HAMMER DRILL Double Insulated Model No. 315.101360 Save this manual for future reference ,A CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 • Safety • Features • Operation • Maintenance • Parts List Sears, Roebuck and C ...
-
Craftsman 315.10136 - page 2
• Table of Contents ..................................................................................................................................................... 2 • General Safety Rules ............................................................................................................................................ 2-3 • Sp ...
-
Craftsman 315.10136 - page 3
Tool Use and Care • Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. • Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is d ...
-
Craftsman 315.10136 - page 4
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. Additional Rules for Safe Operation • Know your power tool. Read operator's manual carefull ...
-
Craftsman 315.10136 - page 5
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alternati ...
-
Craftsman 315.10136 - page 6
KNOW YOUR HAMMER DRILL See Figure I. Before attempting to use your hammer drill, familiarize yourself with all operating features and safety requirements. See Figure 1. _i CAUTION: Carefully read through this entire operator's manual before using your new drill. Pay close attention to the Rules For Safe Operation, Warnings, and Cautions. If yo ...
-
Craftsman 315.10136 - page 7
SWITCH See Figure 2. To turn your hammer drill ON, depress the switch trigger. Release switch trigger to turn your hammer drill OFF. LOCK-ON BUTTON See Figure 2. Your hammer drill is equipped with a "lock-on" feature, which is convenient when continuous drilling for extended periods of time is required. To lock-on, depress the switch trig ...
-
Craftsman 315.10136 - page 8
• Form a loop by forcing end with round holes through slotted hole opposite end. • Place the loop over the cord and pull it tight. • Mount the chuck key by inserting the geared end through the hole in the holder. Large keys in the larger hole, smaller keys in the small hole. VARIABLE SPEED See Figure 5. Your hammer drill has a variable speed ...
-
Craftsman 315.10136 - page 9
To Adjust: • To adjust, loosen the auxiliary handle assembly by turning the handle counterclockwise. • Rotate auxiliary handle assembly to desired operating position. • Securely tighten by turning the auxiliary handle clockwise. USING DEPTH GAGE ROD See Figure 7. Note: When installing depth gage rod, align teeth on depth gage rod with the tee ...
-
Craftsman 315.10136 - page 10
TO INSTALL BITS See Figure 9. • Unplug your hammer drill. ,_ WARNING: Failure to unplug hammer drill your could result in accidental starting causing serious injury. • Open or close the chuck jaws to a point where the opening is slightly larger than the drill bit you intend to use. Also, raise the front of your drill slightly to keep the drill ...
-
Craftsman 315.10136 - page 11
DRILLING See Figure 11. • Depress and release switch trigger to be sure your drill is in OFF position before connecting it to power supply. • Check the direction of rotation lever for correct setting (forward or reverse). See Figure 3. • Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotate ...
-
Craftsman 315.10136 - page 12
CHUCK REMOVAL See Figure 12. The chuck must be removed in order to use some accessories. To remove: • Unplug your drill. _k WARNING: Failure to unplug your drill could result in accidental starting causing serious injury. • Insert a 8 mm (5/16 in.) or larger hex key into the chuck of your drill and tighten chuck jaws securely. • Tap the hex k ...
-
Craftsman 315.10136 - page 13
GENERAL Only the parts shown on parts list, page 17, are intended to be repaired or replaced by the customer. All other parts represent an important part of the double insulation system and should be serviced only at a Sears Service Center. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types ...
-
Craftsman 315.10136 - page 14
The following recommended accessories are currently available at Sears retail stores. • High Speed Bits (For wood or metal) • Masonry Bits • Wood Boring Bits • Hole Saws • 1/2 in. Chuck (9-2980) 1/2 in. Max. 3/4 in. Max. 1-1/2 in. Max. 2-1/2 in. Max. _IL WARNING: The use of attachments or accessories not listed might be hazardous. _, WARN ...
-
Craftsman 315.10136 - page 15
Page 15 ...
Craftsman 315.10136についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもCraftsman 315.10136の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCraftsman 315.10136で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。