Bunn DVの取扱説明書

24ページ 2.59 mb
ダウンロード

ページに移動 of 24

Summary
  • Bunn DV - page 1

    H10X/H5X H5E/DV PC H5 ELEMENT With Digital Control Board SER VICE MANU AL BUNN-O-MA TIC CORPORA TION POST OFFICE BO X 3227 SPRINGFIELD , ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit the Bunn-O-Matic website, at www .bunn. ...

  • Bunn DV - page 2

    2 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specifi ed below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years parts and 1 year ...

  • Bunn DV - page 3

    3 WARNING - Inspection, testing, and repair of electrical equipment should be performed only by qualifi ed ser vice personnel. Disconnect the dispenser fromthe power source when servicing, except when electrical tests are required and the test procedure specifi cally states to connect the dispenser to the power sour ce. 42311 071310 CONTENTS T ro ...

  • Bunn DV - page 4

    4 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic T echnical Ser vice Department. • Inspection, testing, and repair of electrical equipment should be performed only by qu ...

  • Bunn DV - page 5

    5 TROUBLESHOOTING (cont.) Problem Probable Cause Remedy Equipment will not operate (cont.) Automatic refi ll will not oper - ate after drawing hot water . Water fl ows into the tank con- tinuously (Dispenser discon- nected from power source). Water fl ows into the tank con- tinuously (Dispenser connect- ed to power source). Water is cold. 2. Saf ...

  • Bunn DV - page 6

    6 TROUBLESHOOTING (cont.) Problem Probable Cause Remedy Water boils continuously . Dispenser is making unusual noises. Ready indicator will not light. 1. T emperature control 2. Lime build-up 1. Plumbing lines 3. Water supply 1. T emperature control 2. Ready Indicator LED Refer to Service – electronic controls for testing procedures. Inspect the ...

  • Bunn DV - page 7

    7 Faceplate Removal - H5 ELEMENT : After removing top cover , remove the two upper screws securing the faceplate. Carefully lift faceplate straight up until the three lower screws clear the key holes. The check valve, electronic control assembly , safety overfl ow switch, solenoid valve, overfl ow tube tempera- ture sensor and terminal block are ...

  • Bunn DV - page 8

    8 SERVICE Electronic Controls FIG. 8a ELECTRONIC CONTROL P4093.35 V oltage present at Solenoid V alve ? V oltage present at Solenoid V alve ? Overflow Cup Full ? Remove Power Disconnect Level Probe Retry Drain cup No Ye s Ye s Ye s Ye s No No No H5E, H5X LIQUID LEVEL CONTROL PROBLEM: Does Not Refill Does Water Flow ? Replace Probe Unplug Ready Lamp ...

  • Bunn DV - page 9

    9 SERVICE (cont.) Electronic Controls (cont.) Liquid Level Control T est Procedure 1. Disconnect the dispenser from the power sour ce. 2. Check the voltage across terminals 3 & 4 of the electronic control board with a voltmeter . Connect the dispenser to the power source. The indication must be: a.) 100 to 120 volts ac for 100 to 120 volt model ...

  • Bunn DV - page 10

    10 Electronic Controls (cont.) 7. Reconnect the pink wire to terminal 5 of the elec- tronic control assembly . 8. Loosen the compression fi tting, remove the probe from the tank lid, and inspect it for mineral depos- its. Replace it if necessary . Keep the exposed ends of the probe away from any metal surface of the dispenser . 9. Check the voltag ...

  • Bunn DV - page 11

    11 SERVICE (cont.) Electronic Controls (cont.) If voltage was present as described, the temperature control of the system is operating properly . If voltage was not present as described, contact Bunn-O-Matic to order an electronic control board and temperature sensor for evaluation and proceed to #9. 6. Replace the electronic control board. 7. Chec ...

  • Bunn DV - page 12

    12 SERVICE (cont.) Limit Thermostat Location: The limit thermostat is located on the tank lid. T o test the limit thermostat, access will also be needed to the terminal block located at the rear of the dispenser . If voltage was present as described, reconnect the black wire and proceed to #5. If voltage was not present as described, refer to the W ...

  • Bunn DV - page 13

    13 SERVICE (cont.) Safety Overfl ow Switch Location: The safety overfl ow switch is located inside the rear of the dispenser inside the copper overfl ow cup. For testing or removal of the safety overfl ow switch, access may also be needed by removing the two screws attaching the electronic control assembly to its mount- ing bracket. T est Proce ...

  • Bunn DV - page 14

    14 SERVICE (cont.) Solenoid Valve (Late Models) Location: The solenoid valve is located inside the rear of the dispenser on the right side near the bottom. T o test the solenoid valve, access will also be needed to the electronic control board. sound after approximately 5 seconds, as the coil magnet attracts the plunger . 8. Disconnect the dispense ...

  • Bunn DV - page 15

    15 Solenoid Valve (Early Models) Location: The solenoid valve is located behind the large access panel on the left side of the dispenser . T o test the solenoid valve, access will also be needed to the electronic control board. BUNN 90 psig max operating pressure Strainer/Flow Control # 22300.0750 (Repl. Flow Washer #20526.0750) (Repl. Screen #2372 ...

  • Bunn DV - page 16

    16 SERVICE (cont.) T ank Heater Location: The tank heater is located in the tank lid. T est Procedure: 1. Disconnect the dispenser from the power sour ce. 2. Check the voltage across the terminals of the tank heater with a voltmeter . Connect the dispenser to the power source. The indication must be: a.) 100 to 120 volts ac for 100 to 120 volt mode ...

  • Bunn DV - page 17

    Steam Sensor (Thermistor) Location: The thermistor is located on the end of the overfl ow tube above the overfl ow cup. T o test the thermistor , access will also be needed to the electronic control board. SERVICE (cont.) P1993 FIG. 17b LOCA TION H 10X P1993 FIG. 17a LOCA TION H 5X T est Procedure: 1. Disconnect the dispenser from the power sour ...

  • Bunn DV - page 18

    SERVICE (cont.) Dispense Valve (PC Only) Location: The Dispense Valve is located behind control panel. T est Procedures: 1. Check the valve for coil action. T urn on the valve with the dispense button. Listen carefully in the vicinity of the dispense valve for a click as the coil pulls the plunger in. If no sound is heard as described, proceed to # ...

  • Bunn DV - page 19

    42311 071310 19 RELA Y N.O. COM 3 1 5 4 2 F ACTORY J1-1 J1-5 H5-PC NO JUMPER Early H5E, H5X, H10X Install jumper thru ver . 1.04 J3-1 J3-5 J5-1 J4-1 J6-1 NO TE: no jumper used on an y Model star ting with ver . 1.08 J2 J7 MAIN CONTROL BOARD 1 2 3 4 + - + - USED ON H5X ONL Y 120V AC 2 WIRE + GND 120/208V AC 3 WIRE + GND 120/240V AC 3 WIRE + GND SING ...

  • Bunn DV - page 20

    42311 071310 20 230V AC 2 WIRE + GND SINGLE PHASE RELA Y N.O. COM 3 1 5 4 2 F ACTORY J1-1 J1-5 H5-PC NO JUMPER Early H5E, H5X, H10X Install jumper thru ver . 1.04 J3-1 J3-5 J5-1 J4-1 J6-1 NO TE: no jumper used on an y Model star ting with ver . 1.08 J2 J7 MAIN CONTROL BOARD 1 2 3 4 + - + - USED ON H5X ONL Y PINK-22 BLK-24 WHI-24 T ANK t° 39333.000 ...

  • Bunn DV - page 21

    42311 071310 21 BLU-14 BLK-14 BLK-14 T ANK HEA TER BLK-14 LIMIT THERMOST A T 200-240 VOL TS AC 2 WIRE + GND SINGLE PHASE USED ON H5X ONL Y RELA Y N.O. COM 3 1 5 4 2 F ACT ORY J1-1 J1-5 H5-PC NO JUMPER Early H5E, H5X, H10X Install jumper thru ver . 1.04 J3-1 J3-5 J5-1 J4-1 J6-1 NO TE: no jumper used on any Model star ting with ver . 1.08 J2 J7 MAIN ...

  • Bunn DV - page 22

    42311 071310 22 USED ON H5X ONL Y RELA Y N.O. COM 3 1 5 4 2 F ACTORY J1-1 J1-5 H5-PC NO JUMPER Early H5E, H5X, H10X Install jumper thru ver . 1.04 J3-1 J3-5 J5-1 J4-1 J6-1 NO TE: no jumper used on any Model star ting with ver . 1.08 J2 J7 MAIN CONTROL BOARD 1 2 3 4 + - + - 100-120 VOL TS AC or 200-240 VOL TS AC 2 WIRE + GND SINGLE PHASE PINK-22 GRN ...

  • Bunn DV - page 23

    42311 050511 23 RELA Y 3 1 5 4 2 J1-1 J1-5 J3-1 J3-5 J5-1 J4-1 J6-1 J7 PINK-22 GRN-18 WHI/BLU-18 T ANK t° MAIN CONTROL BOARD 1 2 3 4 0-13.8V AC 0-3.3VDC 0-3.3VDC GRY GRY t ° + - + - WHI/VIO-14 RED-18 BLU-14 BLU-14 RED-18 BLK-14 BLK-18 BLK-18 L1 L2 RED RED BLK-18 OVERFLOW PROTECTION SWITCH BLK-14 T ANK HEA TER BLK-14 LIMIT THERMOST A T LIMIT THERM ...

  • Bunn DV - page 24

    42311 050511 24 RELA Y J1-1 J1-5 J3-1 J2-1 J4-1 J2 MAIN CONTROL BOARD 1 2 3 4 + - + - USED ON H5X ONL Y 100-240V AC 2 WIRE + GND SINGLE PHASE PINK BLK WHI T ANK t° 44657.0000B 05/11 ©2011 BUNN-O-MA TIC CORPORA TION GRY GRY t ° STEAM SENSOR TEMP PROBE + - SCHEMA TIC WIRING DIAGRAM H5 ELEMENT GRN/YEL L1 RED WHI/BLU BRN/WHI WHI/RED T ANK HEA TER L2 ...

メーカー Bunn カテゴリー Coffeemaker

Bunn DVのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DVの取扱説明書
- Bunnの製品カード
- パンフレット
- またはBunn DVの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bunn DVの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bunn DVの取り付け説明書、サービスマニュアル、簡易説明書、またはBunn DVのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bunn DVの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bunn DVデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBunn DVを使用するのを助ける技術的文書のことです。説明書は通常、全てのBunn DVユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bunnの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bunn DVの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBunn DVの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bunn DVに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bunn DVデバイスの基本機能を使うにあたってのヒント。 Bunn DVのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bunn DVに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBunn DVのメーカー/サービスへの連絡先に関する情報。

Bunn DVについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBunn DVの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBunn DVで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)