Paradyne 8546の取扱説明書

12ページ 0.25 mb
ダウンロード

ページに移動 of 12

Summary
  • Paradyne 8546 - page 1

    TM 1 8546-A2-GN10-20 October 1997 HotWire 8546 Digital Subscriber Line (DSL) Card Installation Instructions Document Number 8546-A2-GN10-20 October 1997 What is a 8546 DSL Card? A Digital Subscriber Line (DSL) 8546 card is a circuit card assembly (CCA) that contains four Rate Adaptive Digital Subscriber Line (RADSL) ports, an Ethernet interface to ...

  • Paradyne 8546 - page 2

    2 8546-A2-GN10-20 October 1997 T echnical Specifications Specifications Criteria* Size 10.4 inches (L) x 1 1.15 inches (H) x .8 inches (W) Weight Approx. 1.4 lbs. Approvals Safety Certifications Refer to the equipment’s label for approvals on product. Power The DSL card contains a DC-to-DC converter that requires – 48V power input. The – 48V ...

  • Paradyne 8546 - page 3

    3 8546-A2-GN10-20 October 1997 Cables Y ou Need The following customer-provided cables are used with this product: H Plug-ended T elco 50-pin cable for connection from the HotWire DSLAM Line port to the CO POTS splitter shelf, Main Distribution Frame (MDF), or other demarcation point. H One 8-pin modular UTP (Unsheilded T wisted Pair) CA T5 cable f ...

  • Paradyne 8546 - page 4

    4 8546-A2-GN10-20 October 1997 " Procedur e T o install an 8546 DSL card: 1. Remove the filler plate from the desired slot. 2. Insert the 8546 DSL card into this slot: — For a HotWire 8600 DSLAM chassis – hold the 8546 DSL card horizontally with component side facing up and insert it into the left and right card guides. A AC INPUT AC 48VDC ...

  • Paradyne 8546 - page 5

    5 8546-A2-GN10-20 October 1997 3. Slide the 8546 DSL card into the slot until the power and network connectors seat firmly in the mating connectors on the backplane. CAUTION: Do not force the 8546 DSL card into the slot. If it does not seat properly , remove the card and reinstall it. If it still does not seat properly , call service. The 8546 DSL ...

  • Paradyne 8546 - page 6

    6 8546-A2-GN10-20 October 1997 Connecting to a POTS Splitter or an MDF Y ou can connect the HotWire DSLAM chassis containing the 8546 DSL card to a POTS splitter shelf, MDF , or other demarcation point. NOTE: If you are connecting the HotWire DSLAM to a CO POTS splitter , this procedure assumes that the CO POTS splitter shelf is already installed. ...

  • Paradyne 8546 - page 7

    7 8546-A2-GN10-20 October 1997 — On a HotWire 8800 DSLAM chassis: SLO TS 13-18 SLO TS 7-12 SLO TS 1-6 97- 15325 Anchor Mount T elco 50-Pin Connector LINES SLO TS 1-6 LINES Shorter T elco Captive Screw 2. Replace the longer T elco cable captive screw with a shorter connector captive screw , which is provided with the HotWire DSLAM chassis. 3. Inse ...

  • Paradyne 8546 - page 8

    8 8546-A2-GN10-20 October 1997 Connecting the DSL Cards to the Ethernet Hubs or Switches " Procedur e T o connect the 8546 DSL cards to the Ethernet hubs or switches: 1. Plug the end of an 8-pin modular cable into the appropriate LAN/W AN SLOT port of the chassis. For example, if you want to connect to the LAN/W AN port of an 8546 DSL card, in ...

  • Paradyne 8546 - page 9

    97-15449 Pin 1 Pin 8 9 8546-A2-GN10-20 October 1997 Pin Assignments HotWir e 8600 DSLAM LAN/W AN Connector Pinouts The 8-pin modular interface for the LAN/W AN 10BaseT connection on a HotWire 8600 DSLAM chassis has the following pin assignments: Pin Number Use 1 TX Data + 2 TX Data – 3 RX Data + 4 Reserved 5 Reserved 6 RX Data – 7 Reserved 8 Re ...

  • Paradyne 8546 - page 10

    26 97- 15526 50 1 25 10 8546-A2-GN10-20 October 1997 HotWir e 8600 DSLAM T elco 50-pin Connector Pinouts for DSL Loops and POTS Splitters The T elco 50-pin receptacle on the front panel provides the two-wire loop interface from each 8546 DSL port to either the POTS Splitter shelf or , if the loop is not being shared with POTS, then to the MDF . The ...

  • Paradyne 8546 - page 11

    26 97- 15323 50 1 25 11 8546-A2-GN10-20 October 1997 HotWir e 8800 DSLAM T elco 50-pin Connector Pinouts for DSL Loops and POTS Splitters The three T elco 50-pin connectors on the 8800 DSLAM Interface Module provides the two-wire loop interface from each 8546 DSL port to either the POTS splitter shelf or , if the loop is not being shared with POTS, ...

  • Paradyne 8546 - page 12

    SYSTEM OK Alrm T est TX RX Coll 1 2 3 4 ETHERNET DSL POR T RADSL 8546 97-15387 12 8546-A2-GN10-20 October 1997 8546 DSL Card LEDs The following table describes the meaning and states of the LEDs on the 8546 DSL card faceplate. T ype LED LED is . . . Indicating . . . SYSTEM OK Green, Winking* Off Normal operation; card functioning normally . No powe ...

メーカー Paradyne カテゴリー Modem

Paradyne 8546のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 8546の取扱説明書
- Paradyneの製品カード
- パンフレット
- またはParadyne 8546の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Paradyne 8546の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Paradyne 8546の取り付け説明書、サービスマニュアル、簡易説明書、またはParadyne 8546のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Paradyne 8546の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Paradyne 8546デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがParadyne 8546を使用するのを助ける技術的文書のことです。説明書は通常、全てのParadyne 8546ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Paradyneの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Paradyne 8546の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははParadyne 8546の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Paradyne 8546に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Paradyne 8546デバイスの基本機能を使うにあたってのヒント。 Paradyne 8546のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Paradyne 8546に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるParadyne 8546のメーカー/サービスへの連絡先に関する情報。

Paradyne 8546についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもParadyne 8546の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがParadyne 8546で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)