English dropdown-ico

Manual Paradyne 8546

12 pages 0.25 mb
Download

Go to site of 12

Summary
  • Paradyne 8546 - page 1

    TM 1 8546-A2-GN10-20 October 1997 HotWire 8546 Digital Subscriber Line (DSL) Card Installation Instructions Document Number 8546-A2-GN10-20 October 1997 What is a 8546 DSL Card? A Digital Subscriber Line (DSL) 8546 card is a circuit card assembly (CCA) that contains four Rate Adaptive Digital Subscriber Line (RADSL) ports, an Ethernet interface to ...

  • Paradyne 8546 - page 2

    2 8546-A2-GN10-20 October 1997 T echnical Specifications Specifications Criteria* Size 10.4 inches (L) x 1 1.15 inches (H) x .8 inches (W) Weight Approx. 1.4 lbs. Approvals Safety Certifications Refer to the equipment’s label for approvals on product. Power The DSL card contains a DC-to-DC converter that requires – 48V power input. The – 48V ...

  • Paradyne 8546 - page 3

    3 8546-A2-GN10-20 October 1997 Cables Y ou Need The following customer-provided cables are used with this product: H Plug-ended T elco 50-pin cable for connection from the HotWire DSLAM Line port to the CO POTS splitter shelf, Main Distribution Frame (MDF), or other demarcation point. H One 8-pin modular UTP (Unsheilded T wisted Pair) CA T5 cable f ...

  • Paradyne 8546 - page 4

    4 8546-A2-GN10-20 October 1997 " Procedur e T o install an 8546 DSL card: 1. Remove the filler plate from the desired slot. 2. Insert the 8546 DSL card into this slot: — For a HotWire 8600 DSLAM chassis – hold the 8546 DSL card horizontally with component side facing up and insert it into the left and right card guides. A AC INPUT AC 48VDC ...

  • Paradyne 8546 - page 5

    5 8546-A2-GN10-20 October 1997 3. Slide the 8546 DSL card into the slot until the power and network connectors seat firmly in the mating connectors on the backplane. CAUTION: Do not force the 8546 DSL card into the slot. If it does not seat properly , remove the card and reinstall it. If it still does not seat properly , call service. The 8546 DSL ...

  • Paradyne 8546 - page 6

    6 8546-A2-GN10-20 October 1997 Connecting to a POTS Splitter or an MDF Y ou can connect the HotWire DSLAM chassis containing the 8546 DSL card to a POTS splitter shelf, MDF , or other demarcation point. NOTE: If you are connecting the HotWire DSLAM to a CO POTS splitter , this procedure assumes that the CO POTS splitter shelf is already installed. ...

  • Paradyne 8546 - page 7

    7 8546-A2-GN10-20 October 1997 — On a HotWire 8800 DSLAM chassis: SLO TS 13-18 SLO TS 7-12 SLO TS 1-6 97- 15325 Anchor Mount T elco 50-Pin Connector LINES SLO TS 1-6 LINES Shorter T elco Captive Screw 2. Replace the longer T elco cable captive screw with a shorter connector captive screw , which is provided with the HotWire DSLAM chassis. 3. Inse ...

  • Paradyne 8546 - page 8

    8 8546-A2-GN10-20 October 1997 Connecting the DSL Cards to the Ethernet Hubs or Switches " Procedur e T o connect the 8546 DSL cards to the Ethernet hubs or switches: 1. Plug the end of an 8-pin modular cable into the appropriate LAN/W AN SLOT port of the chassis. For example, if you want to connect to the LAN/W AN port of an 8546 DSL card, in ...

  • Paradyne 8546 - page 9

    97-15449 Pin 1 Pin 8 9 8546-A2-GN10-20 October 1997 Pin Assignments HotWir e 8600 DSLAM LAN/W AN Connector Pinouts The 8-pin modular interface for the LAN/W AN 10BaseT connection on a HotWire 8600 DSLAM chassis has the following pin assignments: Pin Number Use 1 TX Data + 2 TX Data – 3 RX Data + 4 Reserved 5 Reserved 6 RX Data – 7 Reserved 8 Re ...

  • Paradyne 8546 - page 10

    26 97- 15526 50 1 25 10 8546-A2-GN10-20 October 1997 HotWir e 8600 DSLAM T elco 50-pin Connector Pinouts for DSL Loops and POTS Splitters The T elco 50-pin receptacle on the front panel provides the two-wire loop interface from each 8546 DSL port to either the POTS Splitter shelf or , if the loop is not being shared with POTS, then to the MDF . The ...

  • Paradyne 8546 - page 11

    26 97- 15323 50 1 25 11 8546-A2-GN10-20 October 1997 HotWir e 8800 DSLAM T elco 50-pin Connector Pinouts for DSL Loops and POTS Splitters The three T elco 50-pin connectors on the 8800 DSLAM Interface Module provides the two-wire loop interface from each 8546 DSL port to either the POTS splitter shelf or , if the loop is not being shared with POTS, ...

  • Paradyne 8546 - page 12

    SYSTEM OK Alrm T est TX RX Coll 1 2 3 4 ETHERNET DSL POR T RADSL 8546 97-15387 12 8546-A2-GN10-20 October 1997 8546 DSL Card LEDs The following table describes the meaning and states of the LEDs on the 8546 DSL card faceplate. T ype LED LED is . . . Indicating . . . SYSTEM OK Green, Winking* Off Normal operation; card functioning normally . No powe ...

Manufacturer Paradyne Category Modem

Documents that we receive from a manufacturer of a Paradyne 8546 can be divided into several groups. They are, among others:
- Paradyne technical drawings
- 8546 manuals
- Paradyne product data sheets
- information booklets
- or energy labels Paradyne 8546
All of them are important, but the most important information from the point of view of use of the device are in the user manual Paradyne 8546.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Paradyne 8546, service manual, brief instructions and user manuals Paradyne 8546. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Paradyne 8546.

Similar manuals

A complete manual for the device Paradyne 8546, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Paradyne 8546 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Paradyne 8546.

A complete Paradyne manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Paradyne 8546 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Paradyne 8546, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Paradyne 8546, that we can find in the current document
3. Tips how to use the basic functions of the device Paradyne 8546 - which should help us in our first steps of using Paradyne 8546
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Paradyne 8546
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Paradyne 8546 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Paradyne 8546?

Use the form below

If you did not solve your problem by using a manual Paradyne 8546, ask a question using the form below. If a user had a similar problem with Paradyne 8546 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)