Delta SS200の取扱説明書

14ページ 0.81 mb
ダウンロード

ページに移動 of 14

Summary
  • Delta SS200 - page 1

    INSTRUCTION MANUAL 16" Scr oll Saw (Model SS200) P ART NO. 905591 - 05-31-02 Copyright © 2002 Delta Machinery ESP AÑOL: PÁGINA 15 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • Delta SS200 - page 2

    2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety precaution ...

  • Delta SS200 - page 3

    3 ADDITIONAL SAFETY RULES FOR SCROLL SA WS WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instru ...

  • Delta SS200 - page 4

    4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cords which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s pl ...

  • Delta SS200 - page 5

    Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized cord will cause a ...

  • Delta SS200 - page 6

    6 ASSEMBL Y WARNING: FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. Fig. 5 Fig. 6 Fig. 7 Fig. 8 T R I J I 1. Remove the blade fr om the upper blade holder . (See the section “ CHANGING BLADES ”, begin with instruction #3) ...

  • Delta SS200 - page 7

    7 6. Re-attach blade to upper blade holder . (See the section “ CHANGING BLADES ”, begin with instruction #6). 7. Assemble table insert (C) Fig. 9, in table as shown. NOTE: Opening in table insert (C) should be positioned toward the fr ont for normal work with the table in the level position and should be positioned toward the right when tiltin ...

  • Delta SS200 - page 8

    8 WRENCH AND BLADE STORAGE A convenient wrench and blade holder (A) Fig. 13, is supplied on the left side of the rear casting, which allows you to store the hex wr enches (C), quickset blade changing wrench (B) and extra scr oll saw blades when not in use. A B Fig. 13 CHANGING BLADES 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Remove table insert. ...

  • Delta SS200 - page 9

    9 6. Insert long end (A) Fig. 16, of quickset blade changing wrench into hole (G) in lower blade holder . This will help align wrench (C) with blade holder scr ew (H). 7. T urn wrench (E) Fig. 17, counterclockwise to loosen screw (H) and r emove blade (F) from lower blade holder . 8. Insert new blade into the lower and upper blade holders in the sa ...

  • Delta SS200 - page 10

    10 TIL TING THE T ABLE The table (A) Fig. 20, on your scroll saw can be tilted up to 45 degrees to the left for bevel cutting operations. 1. T urn the table insert 90 degrees to the right. NOTE: ROT A TE THE T ABLE INSERT (B) FIG. 20A, TO ALLOW YOU TO TIL T THE T ABLE WITHOUT BENDING OR BREAKING THE BLADE. 2. Loosen table lock handle (A) Fig. 20. T ...

  • Delta SS200 - page 11

    11 ADJUSTING HOLDDOWN The bottom of the holddown (A) Fig. 24, should be adjusted so it contacts the top surface of the work being cut by loosening lock handle (B) and moving holddown assembly (C) up or down. Then tighten lock handle (B). NOTE: Lock handle (B) is spring-loaded and can be repositioned by pulling out handle and r epositioning on the n ...

  • Delta SS200 - page 12

    12 MAINTENANCE LUBRICA TION Perform maintenance below after each 20 hours of use. 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Remove the four screws (A) Fig. 26, and side panel (B). 3. Release blade tension by moving blade tension lever to the vertical position. 4. Remove the two pivot bolts and wave washers (C) Fig. 27. 5. Fig. 28 illustrates one ...

  • Delta SS200 - page 13

    13 CHOICE OF BLADES Y our scroll saw will accept a wide variety of 5" flat end blades. Consider the following as a general guideline for selecting a blades. 1. Use a finer blade for cutting thin workpieces, for hard materials, or when a smooth cut is r equired. 2. Use a coarser blade for cutting thick workpieces, when making straight cuts or f ...

  • Delta SS200 - page 14

    T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized service station with pr ...

メーカー Delta カテゴリー Saw

Delta SS200のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SS200の取扱説明書
- Deltaの製品カード
- パンフレット
- またはDelta SS200の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Delta SS200の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Delta SS200の取り付け説明書、サービスマニュアル、簡易説明書、またはDelta SS200のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Delta SS200の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Delta SS200デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDelta SS200を使用するのを助ける技術的文書のことです。説明書は通常、全てのDelta SS200ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Deltaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Delta SS200の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDelta SS200の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Delta SS200に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Delta SS200デバイスの基本機能を使うにあたってのヒント。 Delta SS200のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Delta SS200に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDelta SS200のメーカー/サービスへの連絡先に関する情報。

Delta SS200についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDelta SS200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta SS200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)