English dropdown-ico

Manual Delta SS200

14 pages 0.81 mb
Download

Go to site of 14

Summary
  • Delta SS200 - page 1

    INSTRUCTION MANUAL 16" Scr oll Saw (Model SS200) P ART NO. 905591 - 05-31-02 Copyright © 2002 Delta Machinery ESP AÑOL: PÁGINA 15 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • Delta SS200 - page 2

    2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety precaution ...

  • Delta SS200 - page 3

    3 ADDITIONAL SAFETY RULES FOR SCROLL SA WS WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instru ...

  • Delta SS200 - page 4

    4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cords which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s pl ...

  • Delta SS200 - page 5

    Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized cord will cause a ...

  • Delta SS200 - page 6

    6 ASSEMBL Y WARNING: FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. Fig. 5 Fig. 6 Fig. 7 Fig. 8 T R I J I 1. Remove the blade fr om the upper blade holder . (See the section “ CHANGING BLADES ”, begin with instruction #3) ...

  • Delta SS200 - page 7

    7 6. Re-attach blade to upper blade holder . (See the section “ CHANGING BLADES ”, begin with instruction #6). 7. Assemble table insert (C) Fig. 9, in table as shown. NOTE: Opening in table insert (C) should be positioned toward the fr ont for normal work with the table in the level position and should be positioned toward the right when tiltin ...

  • Delta SS200 - page 8

    8 WRENCH AND BLADE STORAGE A convenient wrench and blade holder (A) Fig. 13, is supplied on the left side of the rear casting, which allows you to store the hex wr enches (C), quickset blade changing wrench (B) and extra scr oll saw blades when not in use. A B Fig. 13 CHANGING BLADES 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Remove table insert. ...

  • Delta SS200 - page 9

    9 6. Insert long end (A) Fig. 16, of quickset blade changing wrench into hole (G) in lower blade holder . This will help align wrench (C) with blade holder scr ew (H). 7. T urn wrench (E) Fig. 17, counterclockwise to loosen screw (H) and r emove blade (F) from lower blade holder . 8. Insert new blade into the lower and upper blade holders in the sa ...

  • Delta SS200 - page 10

    10 TIL TING THE T ABLE The table (A) Fig. 20, on your scroll saw can be tilted up to 45 degrees to the left for bevel cutting operations. 1. T urn the table insert 90 degrees to the right. NOTE: ROT A TE THE T ABLE INSERT (B) FIG. 20A, TO ALLOW YOU TO TIL T THE T ABLE WITHOUT BENDING OR BREAKING THE BLADE. 2. Loosen table lock handle (A) Fig. 20. T ...

  • Delta SS200 - page 11

    11 ADJUSTING HOLDDOWN The bottom of the holddown (A) Fig. 24, should be adjusted so it contacts the top surface of the work being cut by loosening lock handle (B) and moving holddown assembly (C) up or down. Then tighten lock handle (B). NOTE: Lock handle (B) is spring-loaded and can be repositioned by pulling out handle and r epositioning on the n ...

  • Delta SS200 - page 12

    12 MAINTENANCE LUBRICA TION Perform maintenance below after each 20 hours of use. 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Remove the four screws (A) Fig. 26, and side panel (B). 3. Release blade tension by moving blade tension lever to the vertical position. 4. Remove the two pivot bolts and wave washers (C) Fig. 27. 5. Fig. 28 illustrates one ...

  • Delta SS200 - page 13

    13 CHOICE OF BLADES Y our scroll saw will accept a wide variety of 5" flat end blades. Consider the following as a general guideline for selecting a blades. 1. Use a finer blade for cutting thin workpieces, for hard materials, or when a smooth cut is r equired. 2. Use a coarser blade for cutting thick workpieces, when making straight cuts or f ...

  • Delta SS200 - page 14

    T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized service station with pr ...

Manufacturer Delta Category Saw

Documents that we receive from a manufacturer of a Delta SS200 can be divided into several groups. They are, among others:
- Delta technical drawings
- SS200 manuals
- Delta product data sheets
- information booklets
- or energy labels Delta SS200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Delta SS200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Delta SS200, service manual, brief instructions and user manuals Delta SS200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Delta SS200.

Similar manuals

A complete manual for the device Delta SS200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Delta SS200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Delta SS200.

A complete Delta manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Delta SS200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Delta SS200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Delta SS200, that we can find in the current document
3. Tips how to use the basic functions of the device Delta SS200 - which should help us in our first steps of using Delta SS200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Delta SS200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Delta SS200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Delta SS200?

Use the form below

If you did not solve your problem by using a manual Delta SS200, ask a question using the form below. If a user had a similar problem with Delta SS200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)