Wilton 4002の取扱説明書

20ページ 0.64 mb
ダウンロード

ページに移動 of 20

Summary
  • Wilton 4002 - page 1

    Operating Instructions — Parts Manual 1-Inch Belt / 8-Inch Disc Sander Model 4002 Part No. 9078321 Revision A1 ...

  • Wilton 4002 - page 2

    2 T able of Content s Cover ............................................................................................................................... ..... 1 General specifications ......................................................................................................... .3 Machine general safety warning ....................... ...

  • Wilton 4002 - page 3

    3 General Specifications The Wilton Model 4002 sander is designed to serve the varying sanding needs of the professional or the home hobbyist. The sander features both a belt and a disc sanding surface. Specifications Belt 1-inch wide x 42-inches long Disc 8-inches diameter Motor 1/3 horsepower , 1725 rpm Power requirements 1 15 volt s Dimensions: ...

  • Wilton 4002 - page 4

    4 - Misuse of this machine can cause serious injury . - For safety , machine must be set up, used and serviced properly . - Read, understand and follow instructions in the Operating Instructions and Parts Manual which was shipped with your machine. When setting up machine: - Always avoid using machine in damp or poorly lighted work areas. - Always ...

  • Wilton 4002 - page 5

    5 This sander should be grounded in accordance with the National Electrical Code and local codes and ordinances. This work should be done by a qualified electrician. The sander should be grounded to protect the user from electrical shock. W ARNING: Do not connect the sander to a 240 volt power source. The sander motor requires 120 volts alternating ...

  • Wilton 4002 - page 6

    6 Setting up the sander W ARNING: For your own safety , do not connect the sander to the power source until the machine is completely assembled and you have read and understood the entire Operating Instructions and Parts Manual. Unpacking The sander is shipped complete in one carton. Carefully unpack the machine and all loose items from the carton. ...

  • Wilton 4002 - page 7

    7 Figure 3. Installing stud in table bracket Figure 4. Belt table installed and handle in place Figure 5. Dust chutes 2. Remove the screw and spring from the handle assembly . Sep arate the handle and stud. 3. Set the table in place against the sander . 4. Put the flat washer provided in the sander carton on the stud. 5. Install the stud through th ...

  • Wilton 4002 - page 8

    8 Grounding instructions W ARNING: The sander must be grounded while in use to protect the operator from electric shock. Make sure that the receptacle is properly grounded. If you are not sure the receptacle is grounded, have a certified electrician check for proper grounding • In the event of a malfunction or breakdown, grounding provides a path ...

  • Wilton 4002 - page 9

    9 Operating instructions Starting and stopping sander The on/off switch (see Figure 8) is mounted in a switch box on the right side of the sander base. Move the switch to the forward (ON) position to start the sander . Move the switch to the rear (OFF) position to stop the sander . Locking switch in the OFF position We recommend that the switch be ...

  • Wilton 4002 - page 10

    10 Belt table adjustments The belt sander table can be tilted or moved in or out to accommodate the operation being performed. Loosen the locking handle to change the position of the table. Move the table to the desired position and tighten the locking handle. NOTE: The lock handle is spring loaded. Reposition the handle by pulling out on the handl ...

  • Wilton 4002 - page 11

    11 Disc table adjustments Adjusting the table angle W ARNING: When making adjustments, make sure the motor is discon- nected from the power source. W ARNING: T o avoid trapping the work or fingers between the table and sanding disc, the table edge should be positioned a maximum of 1/16- inch from the sanding disc. The disc table is positioned at 90 ...

  • Wilton 4002 - page 12

    12 Changing abrasive belts (continued) Press down on the tracking knob to release belt tension (see Figure 18). Remove the belt from the three pulleys. Install the replacement belt. Replace side cover; secure the cover with two knobs. IMPORT ANT : Some belts have a directional arrow printed on the inside of the belt. In these cases the belt must be ...

  • Wilton 4002 - page 13

    13 Changing abrasive discs (continued) Align the keyway in the disc hub with the key on the motor shaft (see Figure 22). Install the disc plate on the shaft. Position the disc so the face of the disc is even with the edge of the upper disc guard. T ighten the set screw in the hub of the disc plate. If necessary , adjust the position of the upper di ...

  • Wilton 4002 - page 14

    14 T ypical operations (continued) Sanding aluminum on the disc unit with the table tilted and using the miter gauge as a guide (see Figure 26). NOTE: Always sand on the left (downward) side of the sanding disc, as shown. Sanding on the right (upward) side of the sanding disc could cause the workpiece to fly up which could be hazardous. Sanding out ...

  • Wilton 4002 - page 15

    15 T ypical operations (continued) Inside curves can be sanded on the upper sanding belt idler wheel (see Figure 30). The upper cover can either be hinged back or removed. Replacement parts This section provides exploded view illustrations that show the replacement parts for the 1-Inch Belt / 8-Inch Disc Sander . Also provided are parts listings th ...

  • Wilton 4002 - page 16

    16 Exploded View of Sander (Belt Sander Part s ) ...

  • Wilton 4002 - page 17

    17 Item Part No. Number Description 1 564003-1 Hex. Socket Head Screw (M10 x 40 MM) 2 564004-1 Flat Washer (12 MM) 3 564005-1 Spring 4 564006-1 Spacer 5 564007-1 Tracking Adjustment Screw 6 564008-1 Spring 7 564009-1 Support 8 564015-1 Spring Pin (M3 x 20 MM) 9 564016-1 Idler Shaft 10 564017-1 Idler Shaft 1 1 564018-1 Hex. Soc. Set Screw (M5 x 5 MM ...

  • Wilton 4002 - page 18

    18 Exploded View of Sander (Disc Sander Part s ) ...

  • Wilton 4002 - page 19

    19 Item Part No. Number Description 53 564071 1 Hex. Socket Head Screw (M5 x 12 MM) 54 5640721 Drive Pulley 55 5640731 K ey 56 5640741 Motor 57 5640751 Hex Nut (M10) 59 5640461 Flat Washer (10 MM) 60 5640761 Carriage Head Screw (M10 x 12MM) 61 5640771 Base 62 5640781 Pan Head Screw (M4 x 20 MM) 63 5640791 External T ooth Washer (4 MM) 64 564081 1 H ...

  • Wilton 4002 - page 20

    20 Wilton Corporation 300 South Hicks Road Palatine, IL 60067 708/934-6000 F AX 1-800-626-9676 Industrial Products Group: Wilton T ool Wilton Machinery Anderson Products Anderlex Abrasives ...

メーカー Wilton カテゴリー Sander

Wilton 4002のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 4002の取扱説明書
- Wiltonの製品カード
- パンフレット
- またはWilton 4002の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Wilton 4002の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Wilton 4002の取り付け説明書、サービスマニュアル、簡易説明書、またはWilton 4002のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Wilton 4002の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Wilton 4002デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWilton 4002を使用するのを助ける技術的文書のことです。説明書は通常、全てのWilton 4002ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Wiltonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Wilton 4002の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWilton 4002の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Wilton 4002に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Wilton 4002デバイスの基本機能を使うにあたってのヒント。 Wilton 4002のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Wilton 4002に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWilton 4002のメーカー/サービスへの連絡先に関する情報。

Wilton 4002についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWilton 4002の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWilton 4002で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)