-
Wilton 4002 - page 1
Operating Instructions — Parts Manual 1-Inch Belt / 8-Inch Disc Sander Model 4002 Part No. 9078321 Revision A1 ...
-
Wilton 4002 - page 2
2 T able of Content s Cover ............................................................................................................................... ..... 1 General specifications ......................................................................................................... .3 Machine general safety warning ....................... ...
-
Wilton 4002 - page 3
3 General Specifications The Wilton Model 4002 sander is designed to serve the varying sanding needs of the professional or the home hobbyist. The sander features both a belt and a disc sanding surface. Specifications Belt 1-inch wide x 42-inches long Disc 8-inches diameter Motor 1/3 horsepower , 1725 rpm Power requirements 1 15 volt s Dimensions: ...
-
Wilton 4002 - page 4
4 - Misuse of this machine can cause serious injury . - For safety , machine must be set up, used and serviced properly . - Read, understand and follow instructions in the Operating Instructions and Parts Manual which was shipped with your machine. When setting up machine: - Always avoid using machine in damp or poorly lighted work areas. - Always ...
-
Wilton 4002 - page 5
5 This sander should be grounded in accordance with the National Electrical Code and local codes and ordinances. This work should be done by a qualified electrician. The sander should be grounded to protect the user from electrical shock. W ARNING: Do not connect the sander to a 240 volt power source. The sander motor requires 120 volts alternating ...
-
Wilton 4002 - page 6
6 Setting up the sander W ARNING: For your own safety , do not connect the sander to the power source until the machine is completely assembled and you have read and understood the entire Operating Instructions and Parts Manual. Unpacking The sander is shipped complete in one carton. Carefully unpack the machine and all loose items from the carton. ...
-
Wilton 4002 - page 7
7 Figure 3. Installing stud in table bracket Figure 4. Belt table installed and handle in place Figure 5. Dust chutes 2. Remove the screw and spring from the handle assembly . Sep arate the handle and stud. 3. Set the table in place against the sander . 4. Put the flat washer provided in the sander carton on the stud. 5. Install the stud through th ...
-
Wilton 4002 - page 8
8 Grounding instructions W ARNING: The sander must be grounded while in use to protect the operator from electric shock. Make sure that the receptacle is properly grounded. If you are not sure the receptacle is grounded, have a certified electrician check for proper grounding • In the event of a malfunction or breakdown, grounding provides a path ...
-
Wilton 4002 - page 9
9 Operating instructions Starting and stopping sander The on/off switch (see Figure 8) is mounted in a switch box on the right side of the sander base. Move the switch to the forward (ON) position to start the sander . Move the switch to the rear (OFF) position to stop the sander . Locking switch in the OFF position We recommend that the switch be ...
-
Wilton 4002 - page 10
10 Belt table adjustments The belt sander table can be tilted or moved in or out to accommodate the operation being performed. Loosen the locking handle to change the position of the table. Move the table to the desired position and tighten the locking handle. NOTE: The lock handle is spring loaded. Reposition the handle by pulling out on the handl ...
-
Wilton 4002 - page 11
11 Disc table adjustments Adjusting the table angle W ARNING: When making adjustments, make sure the motor is discon- nected from the power source. W ARNING: T o avoid trapping the work or fingers between the table and sanding disc, the table edge should be positioned a maximum of 1/16- inch from the sanding disc. The disc table is positioned at 90 ...
-
Wilton 4002 - page 12
12 Changing abrasive belts (continued) Press down on the tracking knob to release belt tension (see Figure 18). Remove the belt from the three pulleys. Install the replacement belt. Replace side cover; secure the cover with two knobs. IMPORT ANT : Some belts have a directional arrow printed on the inside of the belt. In these cases the belt must be ...
-
Wilton 4002 - page 13
13 Changing abrasive discs (continued) Align the keyway in the disc hub with the key on the motor shaft (see Figure 22). Install the disc plate on the shaft. Position the disc so the face of the disc is even with the edge of the upper disc guard. T ighten the set screw in the hub of the disc plate. If necessary , adjust the position of the upper di ...
-
Wilton 4002 - page 14
14 T ypical operations (continued) Sanding aluminum on the disc unit with the table tilted and using the miter gauge as a guide (see Figure 26). NOTE: Always sand on the left (downward) side of the sanding disc, as shown. Sanding on the right (upward) side of the sanding disc could cause the workpiece to fly up which could be hazardous. Sanding out ...
-
Wilton 4002 - page 15
15 T ypical operations (continued) Inside curves can be sanded on the upper sanding belt idler wheel (see Figure 30). The upper cover can either be hinged back or removed. Replacement parts This section provides exploded view illustrations that show the replacement parts for the 1-Inch Belt / 8-Inch Disc Sander . Also provided are parts listings th ...
-
Wilton 4002 - page 16
16 Exploded View of Sander (Belt Sander Part s ) ...
-
Wilton 4002 - page 17
17 Item Part No. Number Description 1 564003-1 Hex. Socket Head Screw (M10 x 40 MM) 2 564004-1 Flat Washer (12 MM) 3 564005-1 Spring 4 564006-1 Spacer 5 564007-1 Tracking Adjustment Screw 6 564008-1 Spring 7 564009-1 Support 8 564015-1 Spring Pin (M3 x 20 MM) 9 564016-1 Idler Shaft 10 564017-1 Idler Shaft 1 1 564018-1 Hex. Soc. Set Screw (M5 x 5 MM ...
-
Wilton 4002 - page 18
18 Exploded View of Sander (Disc Sander Part s ) ...
-
Wilton 4002 - page 19
19 Item Part No. Number Description 53 564071 1 Hex. Socket Head Screw (M5 x 12 MM) 54 5640721 Drive Pulley 55 5640731 K ey 56 5640741 Motor 57 5640751 Hex Nut (M10) 59 5640461 Flat Washer (10 MM) 60 5640761 Carriage Head Screw (M10 x 12MM) 61 5640771 Base 62 5640781 Pan Head Screw (M4 x 20 MM) 63 5640791 External T ooth Washer (4 MM) 64 564081 1 H ...
-
Wilton 4002 - page 20
20 Wilton Corporation 300 South Hicks Road Palatine, IL 60067 708/934-6000 F AX 1-800-626-9676 Industrial Products Group: Wilton T ool Wilton Machinery Anderson Products Anderlex Abrasives ...
Do you have a question concerning Wilton 4002?
Use the form below
If you did not solve your problem by using a manual Wilton 4002, ask a question using the form below. If a user had a similar problem with Wilton 4002 it is likely that he will want to share the way to solve it.