-
Alvarez N/A - page 1
1 S225 REPAIR MANUAL S225 REPAIR MANUAL ...
-
Alvarez N/A - page 2
2 These instructions are intended to help restore any ailing S225 Passive Loudspeaker back to factory working conditions. They show how to remove and replace the drivers. Please contact Mackie Technical Support (1-800-898-3211) to receive a Service Request Number and Order Number for parts needed for this restoration. They will also help you determ ...
-
Alvarez N/A - page 3
3 Bottom woofer replacement: 1 1 Five screws need to be removed from each side of the grill (ten screws total) using the phillips head screwdriver. A fl at head screwdriver may aid in loosening the grill if it is sticking. 8 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 9 9 10 10 2 2 Keep the ten screws in a safe place. 1 1 3 3 2 2 4 4 3 3 Four screws need to be ...
-
Alvarez N/A - page 4
4 4 4 Carefully begin to remove the woofer. This woofer has a tendency to want to pop out, so please be sure to hold the woofer in place with your free hand while removing the screws with the other hand. Caution: The woofer is approximately 10 pounds with the weight unevenly distributed. Bottom woofer replacement continued: 5 5 The positive (solid ...
-
Alvarez N/A - page 5
5 6 6 The picture above shows what the S225 looks like with the grill and bottom woofer removed. Place the new woofer (part #0010658) where the old one was. Follow the same steps as above, but backwards 5 to 1. Power up the S225 and the new woofer should now be pumping out glorious lows. Awesome, you just replaced a 15” woofer! Bottom woofer repl ...
-
Alvarez N/A - page 6
6 Top woofer replacement: 1 1 Five screws need to be removed from each side of the grill (ten screws total) using the phillips head screwdriver. A fl at head screwdriver may aid in loosening the grill if it is sticking. 8 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 9 9 10 10 2 2 Keep the ten screws in a safe place. 1 1 3 3 2 2 4 4 3 3 Four screws need to be rem ...
-
Alvarez N/A - page 7
7 Top woofer replacement continued: 4 4 Carefully begin to remove the woofer. This woofer has a tendency to want to pop out, so please be sure to hold the woofer in place with your free hand while removing the screws with the other hand. Caution: The woofer is approximately 10 pounds with the weight unevenly distributed. 5 5 The positive (solid yel ...
-
Alvarez N/A - page 8
8 Top woofer replacement continued: 6 6 The picture above shows what the S225 looks like with the grill and top woofer removed. Place the new woofer (part #0010658) where the old one was. Follow the same steps as above, but backwards 5 to 1. Power up the S225 and the new woofer should now be pumping out glorious lows. Awesome, you just replaced a 1 ...
-
Alvarez N/A - page 9
9 High Frequency Driver replacement: 1 1 Five screws need to be removed from each side of the grill (ten screws total) using the phillips head screwdriver. A fl at head screwdriver may aid in loosening the grill if it is sticking. 8 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 9 9 10 10 2 2 Keep the ten screws in a safe place. 3 3 Four screws and fl at washers ...
-
Alvarez N/A - page 10
10 4 4 Carefully begin to remove the entire horn assembly (with the high frequency driver still attached). A fl at head screwdriver may aid in loosening the horn assembly by prying between it and the cabinet. Hold the horn assembly in place with one hand while prying around the edge with your free hand. Caution: The horn weighs about 5 pounds, and ...
-
Alvarez N/A - page 11
11 High Frequency Driver replacement continued: 7 7 Four nuts and eight washers may be removed from the driver using the 8mm open end wrench. Turn counter- clockwise to loosen and remove, clockwise to tighten. The other three are located around the horn assembly. Lift the horn up as the nuts are loosened. It cannot be removed otherwise. Notice that ...
-
Alvarez N/A - page 12
12 High Frequency Driver replacement continued: 10 10 This is what the high frequency driver looks like removed from the horn assembly. Four headless screws need to be removed from the driver. Pliers could help if the screws are too tight. Turn counter- clockwise to loosen and remove, clockwise to tighten. 11 11 Keep the four headless screws in a s ...
-
Alvarez N/A - page 13
13 3 3 The horn assembly is shown above with the high frequency driver circled. Four screws need to be removed from the driver using the 3mm allen wrench. 4 4 Keep the four screws in a safe place. 5 5 The diaphragm and plate adapter are easily removed from the horn assembly. Notice the terminal locations in relation to the indents of the high frequ ...
-
Alvarez N/A - page 14
14 7 7 This is what the plate adapter (left) and diaphragm (right) both look like. Place the new diaphragm (part # coming soon) where the old one was. Follow the same steps as above, but backwards 6 to 1. Power up the S225 and the new diaphragm should now be pumping out those highs again. Sweet, you just replaced a diaphragm! Diaphragm replacement ...
-
Alvarez N/A - page 15
15 This page left blank intentionally ...
Alvarez N/Aについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもAlvarez N/Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAlvarez N/Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。