Pelco TI2550の取扱説明書

28ページ 1.56 mb
ダウンロード

ページに移動 of 28

Summary
  • Pelco TI2550 - page 1

    INSTALLATION/OPERATION C1309M-A (9/08) TI2535 and TI2550 Models TI2500 Series Fixed-Mount Thermal Imager ...

  • Pelco TI2550 - page 2

    2 C1309M-A (9/08) Contents Important Safe ty Instruct ions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco TI2550 - page 3

    C1309M-A (9/08) 3 List of Illustrations 1 Exploded View of TI25 00 Series Thermal Imager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 TI2535 and TI2550 Series Resource D isc GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco TI2550 - page 4

    4 C1309M-A (9/08) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed al l warnings. 4. Follow all instructions. 5. Do not bl ock any ven tilation openings. Ins tall in accordance with the manu facturer’ s instructions. 6. Do not install near any heat sources such as radiat ors, heat registers, stoves, or ...

  • Pelco TI2550 - page 5

    C1309M-A (9/08) 5 Regulatory Notices This device co mplies with Pa rt 15 of th e FCC Rules. Oper ation is subjec t to the following two co nditions: (1) this device may n ot cause ha rmful interference, and (2 ) this device must accept any inte rference received, including interference tha t may cause undesired operat ion. RADIO AND TELEVISION INTE ...

  • Pelco TI2550 - page 6

    6 C1309M-A (9/08) Description The TI2500 Series combines a powerful advan ced thermal imagin g device in a compact fixed -mount environm ental enclosure . The TI2500 Series ca meras suppo rt seria l communicati on for co ntrol of camera foc us and ot her featur es. The se rial prot ocol is u ser-co nfigurable using a DIP switch on the camera assemb ...

  • Pelco TI2550 - page 7

    C1309M-A (9/08) 7 Setup Before configur ing the camera settings or ins talling the unit , you must remove the camera asse mbly from the encl osure to set up the ba sic wiring configuratio ns (refer to Bench Setup on page 9). The camera can either be configured on a bench using a PC in a lab environment, or using a lap top in the field. The setu p i ...

  • Pelco TI2550 - page 8

    8 C1309M-A (9/08) INSTALLING SOFTWARE MINIMUM SYSTEM REQUIREMENTS • PC (Pentium ® Pr o processor , 166 MHz) with Windo ws ® NT 4 (or later , not inclu ding Windows Vista ® ) • RAM: 128 Mbyte • Hard drive : 10 GB • Screen resol ution: 80 0 x 600 pix els or highe r • Serial communica tion port T o install the TI 25 GUI config uration sof ...

  • Pelco TI2550 - page 9

    C1309M-A (9/08) 9 BENCH SETUP DISASSEMBLE THE ENCLOSURE 1. Use the supplied 1/8-inch he x wrench to loosen the two captive hex scr ews on the enclosure’ s back plate. 2. Pull the “T” handle on the enclos ure’ s back plate to remove the enclosure sled. 3. Disconnect the gr ound cable from the ground stud on the insid e of the enclosure ’ s ...

  • Pelco TI2550 - page 10

    10 C1309M-A (9/08) CONNECT WIRING 1. Pull the shielded power ca ble through the gland on the left side of the enclosure’ s back plate. NOTES: • To prevent the e ntrance of dust or water, proper cabling (not supplied) must be used when wiring the enclosure. Use of flat ca ble or multiple cables will prev ent the proper seal of th e liquid-tight ...

  • Pelco TI2550 - page 11

    C1309M-A (9/08) 11 4. Connect the input pow er wiring for either 24 VDC or 24 V AC to the screw terminals for pins 6 and 7 on the detachable con necto r (refer to Figure 5). Figure 5. Wiring to the Detachable Connector 5. Connect the temporary se rial communication interface wiring comi ng fr om your PC to the approp riate screw terminals fo r pins ...

  • Pelco TI2550 - page 12

    12 C1309M-A (9/08) INTERFACING WITH A PC 1. Attach the end of the ser ial cable that is not connected to the camera’ s detachable connector to your PC’ s serial port. 2. Procee d to Configuration on page 15; follow all steps i n the Configur ation section before completing th e bench setup using t he remaining steps in this section. 3. After co ...

  • Pelco TI2550 - page 13

    C1309M-A (9/08) 13 FIELD SETUP DISASSEMBLE THE ENCLOSURE 1. Use the supplied 1/8-inch he x wrench to loosen the two captive hex scr ews on the enclosure’ s back plate. 2. Pull the “T” handle on the enclos ure’ s back plate to remove the enclosure sled. 3. Disconnect the gr ound cable from the ground stud on the insid e of the enclosure ’ ...

  • Pelco TI2550 - page 14

    14 C1309M-A (9/08) REASSEMBLE THE ENCLOSURE 1. Place t he supplied desiccant bag at the back of the enclosure . 2. Make sure that the lubr icated O-rings o n the front and re ar covers of the enclosure a re free of dirt and d ebris. 3. Reinstall the camera assembly . a. Slide the camera assembly into th e front of the enclosure, making sure that t ...

  • Pelco TI2550 - page 15

    C1309M-A (9/08) 15 Configuration The camera se tup must be complete b efore the camera can be configured (refer to Setup on page 7). T o open th e TI25 GUI configur ation software, on your PC go to Start >Programs>Pelco>TI25 GUI. CAMERA T AB SAVE SETTINGS After changing camer a settings on any o f the GUI tabs, click th e Save Sett ings bu ...

  • Pelco TI2550 - page 16

    16 C1309M-A (9/08) Perform Manual FFC Occasionall y , image qu ality may degrade . When this happ ens, perform a man ual FFC. After manua lly performing this process , the c amera restarts the frequency clock and re sets the baseline temperat ure. T o manually perform the FFC: 1. Click the Camera tab. 2. Click the Manual button in the Flat Field Co ...

  • Pelco TI2550 - page 17

    C1309M-A (9/08) 17 V IDEO T AB CHANGING THE IMAGE ORIENTATION MODE Image orientat ion allows y ou to correct the video i n the event t hat the came ra is mounte d inversel y (in a ceiling mounted inst a llation, f or example). T o change the image orientation: 1. Click the Vi deo tab (refer to Figur e 7). 2. Click the Invert button in the Image Ori ...

  • Pelco TI2550 - page 18

    18 C1309M-A (9/08) CHANGING THE POLARITY/LUT SETTING The Polarit y/LUT setting programs th e specific pa lette of co lors to rep resent the t emperature s in the the rmal image. These colo rs are not calibrated to a specif ic temperature. Rather , they represent the tempe rature variations within t he thermal image. The follo wing table lists the a ...

  • Pelco TI2550 - page 19

    C1309M-A (9/08) 19 Pan When the “Zoom 2x” check bo x is selected, you can move th e zoomed array region within the full-array area; this digitally simu l ates panning an d tilting. Pan ning and ti lting are de fined as movi ng the camer a image in t he horizont al and vert ical axes, res pectively. There are t wo methods to pan and ti lt using ...

  • Pelco TI2550 - page 20

    20 C1309M-A (9/08) AGC T AB The defaul t setting s on the au tomatic ga in control (A GC) tab offe r the best image quali ty for most s cenes. Y ou can make AG C adj ust ments to configure th e camera to p roduce no i mage or an all black i mage. Restor ing the fa ctory defau lts will retu rn the camer a to its fa ctory default settings and likely ...

  • Pelco TI2550 - page 21

    C1309M-A (9/08) 21 LINEAR PARAMETERS The linear parameters a re made avai lable depe nding on the mode sele cted. The following settings are ava ilable for Linear Parameters: • Contrast: Use the Contrast setting to adjust the contrast across the colo r palette. – Increase th e Contrast s etting to re present midr ange temperat ures closer to th ...

  • Pelco TI2550 - page 22

    22 C1309M-A (9/08) ABOUT T AB Click the Abou t tab (ref er to Figu re 9) to ac cess basic camera inform ation. If the camer a is connected to the PC correctly , the fo llowing cam era information a ppears: • Serial number • Part numbe r • Software ve rsion • Firmware version This information needs to be pr ovided when contacting Pelco Prod ...

  • Pelco TI2550 - page 23

    C1309M-A (9/08) 23 Installation The TI2500 Series fixed- mount thermal i mager can be mounted usin g an approp riate wall, ce iling, or pe destal mount (refer to t he product specification sh eet for a list of compat ible mounts). For prop er installation, refer to the instructions su pplied wit h the moun t. The enclosure should be at tached to th ...

  • Pelco TI2550 - page 24

    24 C1309M-A (9/08) T roubleshooting NOTE: The system contains no user -serviceable pa rts . If there is a problem with your system, it must be returned to Pelco for servici ng . Symptom: Degrading vide o quality Occasional ly , image quality may degrade. 1. Perform a manual FFC. Af ter manually performing this process, the ca mera restarts the f re ...

  • Pelco TI2550 - page 25

    C1309M-A (9/08) 25 Maintenance CLEANING THE LENS 1. Saturate a piece of optical-grade tissue with deionized water an d drape it over the le ns. 2. Let the surface tension of the water pull the tissue onto the surface of the len s, and then drag the tissue acro ss the lens. 3. Repeat this proced ure sever al times, using a new p iece of ti ssue each ...

  • Pelco TI2550 - page 26

    26 C1309M-A (9/08) Specifications Electrical Input Power 4 W , 6.2 VA nominal Input V oltage 18–27 V AC; 14–32 VDC Power Require ments 4 W Heater 24 V AC, dual elements, thermostatically controlled Heater opera tes as a def ogger; acti vates ON at 70 °F (21°C), OF F at 85°F (29°C) Heater operate s as a defroster ; activates ON at 40°F (4° ...

  • Pelco TI2550 - page 27

    PRODUCT W ARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without c harge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW3000 Series unsh ielded twisted pair (UTP) tra ...

  • Pelco TI2550 - page 28

    Australia | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Arab Emirates | United Kingdom | United States W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: (800) 289-9100 Fax: (800) 289-9150 International T el: +1 (559) 292-1981 Fax: ...

メーカー Pelco カテゴリー Security Camera

Pelco TI2550のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- TI2550の取扱説明書
- Pelcoの製品カード
- パンフレット
- またはPelco TI2550の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Pelco TI2550の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Pelco TI2550の取り付け説明書、サービスマニュアル、簡易説明書、またはPelco TI2550のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Pelco TI2550の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Pelco TI2550デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPelco TI2550を使用するのを助ける技術的文書のことです。説明書は通常、全てのPelco TI2550ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Pelcoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Pelco TI2550の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPelco TI2550の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Pelco TI2550に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Pelco TI2550デバイスの基本機能を使うにあたってのヒント。 Pelco TI2550のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Pelco TI2550に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPelco TI2550のメーカー/サービスへの連絡先に関する情報。

Pelco TI2550についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPelco TI2550の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPelco TI2550で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)