Cuno SQC Seriesの取扱説明書

17ページ 0.24 mb
ダウンロード

ページに移動 of 17

Summary
  • Cuno SQC Series - page 1

    © 2001 CUNO Incorporated 98-880040 1101 SQC Series Owner's Manual This Manual is for the Installation, Operation, and Maintenance of the WATER FACTORY SYSTEMS ® SQC Series Reverse Osmosis (RO) Drinking Water Appliance ...

  • Cuno SQC Series - page 2

    INTRODUCTION This manual explains the installation, operation and maintenance of the Water Factory Systems ® SQC Series Reverse Osmosis (RO) Drinking Water Appliances. Please read each section of this manual carefully. The specific model chosen should be appropriate for the local water conditions and the customer's needs. Check the Performanc ...

  • Cuno SQC Series - page 3

    ...

  • Cuno SQC Series - page 4

    A. DETERMINE THE APPLIANCE LOCA TIONS The appliance can be located under a sink or in a base- ment depending on space availability and the customer's pref- erence. If a basement installation is selected, additional tub- ing, hardware and fittings may be needed and a hole will have to be made from inside the cabinet, through the floor, to the b ...

  • Cuno SQC Series - page 5

    C. PREP ARE THE APPLIANCE FOR INST ALLA TION Open the shipping carton and remove the components. Check to see that all of the installation parts are present. They should include the purification assembly, storage tank, faucet, installation hardware, RO membrane cartridge and tubing. Check to see that the air supply in the empty tank is approxi- mat ...

  • Cuno SQC Series - page 6

    E. MOUNT THE F AUCET Undercounter installations generally require that the faucet's built-in air gap be used. In basement installations, the built-in air gap does not have to be used if one is provided elsewhere on the drain line. For Basement Installations Without An Air Gap Module See Installation Instructions O. IMPORTANT: The Uniform Plumb ...

  • Cuno SQC Series - page 7

    F . INST ALL THE FEED WA TER T APPING V AL VE AND TUBING The feed water tapping valve which is supplied, is designed to be used on 3/8" to 1/2" OD soft copper tubing (plain or chromed) and rigid metal pipe. Do not use it on flexi- ble ribbed tubing, because it has too thin a wall thickness and it requires special hardware. Soft Copper Tub ...

  • Cuno SQC Series - page 8

    G. PREFILL AND SANITIZE THE STORAGE T ANK Prefilling the storage tank is always recommended so that there is pressure to check for leaks as well as sufficient water to flush the carbon postfilter. The SQC RO Drinking Water Appliance is furnished with a container of special sanitizing gran- ules. It is important to use a sanitizer when prefilling th ...

  • Cuno SQC Series - page 9

    I. INST ALL THE PURIFICA TION ASSEMBL Y AND STORAGE T ANK For Basement Installation See Installation Instructions O. Undercounter Installation: The purification assembly is usually mounted to the right or the left side wall inside of the sink cabinet, taking into consider- ation the space available and the tank location. Generally, the storage tank ...

  • Cuno SQC Series - page 10

    1 Push in grey collet to release tubing. 2 T ubing is secured in. Grey Collet T ube O-Ring Push tubing straight in as far as it will go. 1 Pull tubing straight out. 2 T o Attach T ubing T o Release T ubing This product is outfitted with user friendly ‘Push In’ connectors. Proper use of the connectors is shown in the diagrams. It is most importa ...

  • Cuno SQC Series - page 11

    10 Fig. 7 (FLOOR) Faucet without Air Gap 3/8” Blue T ubing* For refrigerator icemaker or water dispenser hookup, tee into tubing Feedwater T apping Valve Cold Water Supply Pipe 3/8” Y ellow T ubing* Storage T ank** 1/4” green tubing Air Gap Device (e.g. Gap-A-Flow) Laundry Sink, Standpipe or Floor Drain (Basement Floor) Storage T ank Valve Re ...

  • Cuno SQC Series - page 12

    11 Teflon is a registered trademark of E.I. DuPont O. APPENDIX FOR BASEMENT INST ALLA TIONS The following variations are generally required for basement installations: INSTALL THE DRAIN CONNECTION For basement installations, the drain saddle is generally not used. Instead, the RO reject line (SFC tubing) is routed so that it drains into a laundry s ...

  • Cuno SQC Series - page 13

    P . INST ALLA TION TROUBLESHOOTING Problem: Leak at the feed water tapping valve. Cause: Tapping valve is not clamped tightly enough. Solution: Tighten the tapping valve clamp screws evenly and firmly keeping both halves of the bracket parallel. Be sure not to deform tubing. Problem: Leak at the drain saddle. Cause: Drain saddle not clamped tightly ...

  • Cuno SQC Series - page 14

    A. IMPORT ANT WA TER QUALITY ASSURANCE REQUIREMENTS Reverse Osmosis drinking water appliances contain treatment components that are critical for the effective reduction of Total Dissolved Solids (TDS) as well as inor- ganic chemical contaminants. Water Factory Systems ® strongly recommends that the user test the water periodical- ly (every six mon ...

  • Cuno SQC Series - page 15

    When to Replace the RO Membrane Cartridge • As determined by a built-in percent rejection (PR) monitor: The monitor is factory preset so that a green light will be displayed when the water quality is good, and a red or yellow light indicates that cartridge replacement may be necessary. If a red or yellow light is displayed, the faucet should be o ...

  • Cuno SQC Series - page 16

    1) Close the feed water tapping valve and lift up on the faucet handle to empty the water in the storage tank. It should feel light when empty. 2) Shut off the faucet and close the valve at the top of tank. Disconnect the 3/8" yellow tubing from the back for the purification assembly. (Refer to Fig. 6 on the use of the special "Push-In&qu ...

  • Cuno SQC Series - page 17

    CUNO Incorporated 400 Research Parkway Meriden, CT 06450, U.S.A. Toll Free: 1-800-733-1199 Worldwide: 203-237-5541 Fax: 203-238-8701 www.waterfactorysystems.com • www.cuno.com ...

メーカー Cuno カテゴリー Water System

Cuno SQC Seriesのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SQC Seriesの取扱説明書
- Cunoの製品カード
- パンフレット
- またはCuno SQC Seriesの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cuno SQC Seriesの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cuno SQC Seriesの取り付け説明書、サービスマニュアル、簡易説明書、またはCuno SQC Seriesのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cuno SQC Seriesの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cuno SQC Seriesデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCuno SQC Seriesを使用するのを助ける技術的文書のことです。説明書は通常、全てのCuno SQC Seriesユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cunoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cuno SQC Seriesの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCuno SQC Seriesの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cuno SQC Seriesに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cuno SQC Seriesデバイスの基本機能を使うにあたってのヒント。 Cuno SQC Seriesのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cuno SQC Seriesに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCuno SQC Seriesのメーカー/サービスへの連絡先に関する情報。

Cuno SQC Seriesについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCuno SQC Seriesの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCuno SQC Seriesで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)