Cuno SQC Proの取扱説明書

15ページ 0.27 mb
ダウンロード

ページに移動 of 15

Summary
  • Cuno SQC Pro - page 1

    © 2001 CUNO Incorporated 98-91220 0601 CUNO Incorporated 400 Research Parkway Meriden, CT 06450, U.S.A. Toll Free: 1-800-733-1199 Worldwide: 203-237-5541 Fax: 203-238-8701 www.waterfactorysystems.com • www.cuno.com ...

  • Cuno SQC Pro - page 2

    INTRODUCTION This manual explains the installation, operation and maintenance of the Water Factory Systems ® SQC Series Reverse Osmosis (RO) Drinking Water Appliances. Please read each section of this manual care - fully. The specific model chosen should be appropriate for the local water conditions and the customer's needs. Check the Perform ...

  • Cuno SQC Pro - page 3

    A. DETERMINE THE APPLIANCE LOCATION The appliance can be located under a sink or in a basement depending on space availability and the customer's preference. If a basement installation is selected, additional tubing, hardware and fittings may be needed and a hole will have to be made from inside the cabinet, through the floor, to the basement. ...

  • Cuno SQC Pro - page 4

    C. PREPARE THE APPLIANCE FOR INSTALLATION Open the shipping carton and remove the components. Check to see that all of the installation parts are present. They should include the purification assembly, storage tank, faucet, installation hardware, RO membrane cartridge and tubing. Check to see that the air supply in the empty tank is approxi - matel ...

  • Cuno SQC Pro - page 5

    E. MOUNT THE FAUCET Undercounter installations generally require that the faucet's built-in air gap be used. In basement installations, the built-in air gap does not have to be used if one is provided elsewhere on the drain line. For Basement Installations Without An Air Gap Module See Installation Instructions O. IMPORTANT: The Uniform Plumbi ...

  • Cuno SQC Pro - page 6

    F . INSTALL THE FEED WATER TAPPING VALVE AND TUBING The feed water tapping valve which is supplied, is designed to be used on 3/8" to 1/2" OD soft copper tubing (plain or chromed) and rigid metal pipe. Do not use it on flexi - ble ribbed tubing, because it has too thin a wall thickness and it requires special hardware. Soft Copper Tubing ...

  • Cuno SQC Pro - page 7

    5) Turn the feedwater tapping valve handle clockwise to close the valve. With a wrench, tighten the nut/seal around the valve handle stem. 6) Remove the cover from the appliance and disconnect the orange 1/4" tubing from the feedwater fitting. (See Fig. 6) 7) Connect one end of the orange tubing to the feedwater tapping valve using the brass c ...

  • Cuno SQC Pro - page 8

    I. INSTALL THE PURIFICATION ASSEMBLY AND STORAGE TANK For Basement Installation See Installation Instructions O. Undercounter Installation: The purification assembly is usually mounted to the right or the left side wall inside of the sink cabinet, taking into consider - ation the space available and the tank location. Generally, the storage tank is ...

  • Cuno SQC Pro - page 9

    L. START UP THE APPLIANCE 1) Double check to see that all of the connections are secure. 2) Open the feedwater tapping valve and check the appliance for leaks. If any leaks are detected, close the valve and correct the problem before proceeding. NOTE: If a leak occurs at a "Push In" plastic fitting, then refer to Fig. 6. 3) Open the stora ...

  • Cuno SQC Pro - page 10

    O. APPENDIX FOR BASEMENT INSTALLATIONS The following variations are generally required for basement installations: INSTALL THE DRAIN CONNECTION For basement installations, the drain saddle is generally not used. Instead, the RO reject line (SFC tubing) is routed so that it drains into a laundry sink, floor drain, or standpipe through an approved ai ...

  • Cuno SQC Pro - page 11

    Teflon is a registered trademark of E.I. DuPont 11 P. INSTALLATION TROUBLESHOOTING Problem: Leak at the feedwater tapping valve. Cause: Tapping valve is not clamped tightly enough. Solution: Tighten the tapping valve clamp screws evenly and firmly keeping both halves of the bracket parallel. Be sure not to deform tubing. Problem: Leak at the drain ...

  • Cuno SQC Pro - page 12

    A. IMPORTANT WATER QUALITY ASSURANCE REQUIREMENTS Reverse Osmosis drinking water appliances contain treat - ment components that are critical for the effective reduction of Total Dissolved Solids (TDS) as well as inorganic chemical contaminants. Water Factory Systems ® strongly recommends that the user test the water periodically (every six months ...

  • Cuno SQC Pro - page 13

    C. REPLACING THE RO MEMBRANE CARTRIDGE The life of the RO membrane cartridge depends on the local water conditions and proper maintenance, e.g., regular fil - ter changes. Under typical conditions, the RO membrane life ranges from 18-36 months. Unlike the filter cartridges, the RO membrane cartridge life is not determined by the amount of water use ...

  • Cuno SQC Pro - page 14

    4) Fill the sanitizing device with the following recommended dosage of common household bleach: • A standard 2.5 gallon tank - 1/2 teaspoon (3 ml) • Alternate size tanks - 1/2 teaspoon (3 ml) per 2.5 gallons of tank capacity 5) Open the feedwater tapping valve to force water and sanitizer into the storage tank. Allow about three (3) minutes to ...

  • Cuno SQC Pro - page 15

    Appendix 1. Electrical Diagram 15 ...

メーカー Cuno カテゴリー Water System

Cuno SQC Proのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SQC Proの取扱説明書
- Cunoの製品カード
- パンフレット
- またはCuno SQC Proの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cuno SQC Proの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cuno SQC Proの取り付け説明書、サービスマニュアル、簡易説明書、またはCuno SQC Proのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cuno SQC Proの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cuno SQC Proデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCuno SQC Proを使用するのを助ける技術的文書のことです。説明書は通常、全てのCuno SQC Proユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cunoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cuno SQC Proの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCuno SQC Proの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cuno SQC Proに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cuno SQC Proデバイスの基本機能を使うにあたってのヒント。 Cuno SQC Proのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cuno SQC Proに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCuno SQC Proのメーカー/サービスへの連絡先に関する情報。

Cuno SQC Proについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCuno SQC Proの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCuno SQC Proで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)