ADTRAN T200 FNIDの取扱説明書

16ページ 0.12 mb
ダウンロード

ページに移動 of 16

Summary
  • ADTRAN T200 FNID - page 1

    1 Section 61245201L1-5, Issue 3 61245201L1-5C FNID and T200 FNID Fractional T1 Network Interface Device Installation and Maintenance CONTENTS 1. GENERAL ............................................................................ 1 2. INSTALLATION .................................................................. 2 3. CONNECTIONS .................. ...

  • ADTRAN T200 FNID - page 2

    2 Section 61245201L1-5, Issue 3 61245201L1-5C With the exception of the physical dimensions of the units, the FNID and T200 FNID units are functionally identical. The FNID terminates local loop DSL signals originating from the Central Office (CO) unit and transforms the DSL signal into fractional T1 signals to be delivered to the customer. The DSL ...

  • ADTRAN T200 FNID - page 3

    3 Section 61245201L1-5, Issue 3 61245201L1-5C 3. CONNECTIONS All connections of the FNID are made through card edge connectors. Table B gives the card edge pin assignments for the FNID circuit pack. The circuit pack operates in either the standalone chassis (P/N 1242034L2), the ADTRAN HR4 HDSL shelf (P/N 1242008L1), or the ADTRAN HR12 HDSL shelf (P ...

  • ADTRAN T200 FNID - page 4

    4 Section 61245201L1-5, Issue 3 61245201L1-5C 5. CONTROL PORT OPERATION The FNID provides a faceplate-mounted DB9 connector that supplies an RS-232 interface for connection to a controlling terminal. The pinout of the DB9 is illustrated in Figure 4. The terminal interface operates at data rates from 2.4 kbps to 19.2 kbps. The asynchronous data form ...

  • ADTRAN T200 FNID - page 5

    5 Section 61245201L1-5, Issue 3 61245201L1-5C From the Main menu the following screens can be accessed. 1. Current System Status 2. Performance History 3. ADTRAN Information 4. Loopback Options 5. Self Test 6. Provisioning 7. Troubleshooting The Current System Status screen, illustrated in Figure 7, provides quick access to status information for b ...

  • ADTRAN T200 FNID - page 6

    6 Section 61245201L1-5, Issue 3 61245201L1-5C A measure of signal quality for each HDSL loop is displayed in graphic form on the bottom right and left of the screen. The measure is from 0 (poor signal quality) to 9 (excellent signal quality). Guidelines for interpreting the indicators are: 0 Noise margin is ≤ 0 dB ( ≈ 10 -7 BER) 1-8 Margin meas ...

  • ADTRAN T200 FNID - page 7

    7 Section 61245201L1-5, Issue 3 61245201L1-5C Figure 5. Introductory Menu Screen ADTRAN 901 Explorer Boulevard Huntsville, Alabama 35806-2807 For Information or Technical Support, Normal Support Hours ( 7am - 7pm CST ) or Emergency Support Hours ( 7x24 ) Voice Toll Free: 800.726.8663 Fax: 256.963.6217 Voice: 256.963.8100 Internet: www.adtran.com ? ...

  • ADTRAN T200 FNID - page 8

    8 Section 61245201L1-5, Issue 3 61245201L1-5C Figure 7. Current System Status Screen FT1-DP CURRENT SYSTEM STATUS FNID NETWORK (DSL) ELAPSED TIME 00:08:18 CUSTOMER (DSL) ---------------------- ----------------- 00 dB <- LOSS -> 00 dB NO <- SYNC -> NO 000/00000 <- ES 15M/24H -> 000/00000 000/00000 <- SES 15M/24H -> 000/00000 ...

  • ADTRAN T200 FNID - page 9

    9 Section 61245201L1-5, Issue 3 61245201L1-5C Figure 9. Loopback Options Screen LOOPBACK OPTIONS FT1-DP FNID _____ _____ | | | | | | | | —-->| | | |<—- | | | | NET | |<===========================>| | CUST | | | | <—--| | | |—> | | | | | | | | |_____| |_____| 1) LOOPBACK TO NETWORK AT FT1-DP =INACTIVE 2) LOOPBACK TO CUSTOME ...

  • ADTRAN T200 FNID - page 10

    10 Section 61245201L1-5, Issue 3 61245201L1-5C Figure 11. Provisioning Options Screen PROVISIONING ___________________________________________________ ______________________ | | | | PROVISIONS CURRENT SETTINGS | HARDWARE SETTINGS | | ------------------------------------------ | ----------------- | | 1. DS1 (FNID) LINE CODE = B8ZS | B8ZS | | 2. DS1 ...

  • ADTRAN T200 FNID - page 11

    11 Section 61245201L1-5, Issue 3 61245201L1-5C Figure 13. DSL Deployment Guidelines 6. DSL DEPLOYMENT GUIDELINES The ADTRAN FT1 DSL system is designed to provide Fractional DS1-based services over loops designed to comply with Carrier Service Area (CSA) guidelines. CSA deployment guidelines are given below. 1 . All loops are non-loaded only. 2. For ...

  • ADTRAN T200 FNID - page 12

    12 Section 61245201L1-5, Issue 3 61245201L1-5C 7. TROUBLESHOOTING PROCEDURES Table E is a troubleshooting guide for the FNID. 8. MAINTENANCE The ADTRAN FNID requires no routine maintenance. In case of equipment malfunction, use the faceplate Bantam jack connectors to help locate the source of the problem. ADTRAN does not recommend that repairs be p ...

  • ADTRAN T200 FNID - page 13

    13 Section 61245201L1-5, Issue 3 61245201L1-5C Loop Interface: Modulation Type ................................................. 2B1Q Mode .................................................................... Full Duplex, Echo Cancelling Number of Pairs .................................................. One Bit Rate ................................. ...

  • ADTRAN T200 FNID - page 14

    A-1 Section 61245201L1-5, Issue 3 61245201L1-5C Appendix A FT1 Loopbacks 1. GENERAL This Appendix is an overall reference to the loopback capabilities of the ADTRAN Fractional T1 system. Included in this Appendix is a description of the FT1 loopbacks and the methods for activating the FT1 loopbacks. 2. FT1 LOOPBACKS Figure A-1 shows the application ...

  • ADTRAN T200 FNID - page 15

    A-2 Section 61245201L1-5, Issue 3 61245201L1-5C There is one loopback available to the FT1 Repeaters. The FT1 Repeater Network loopback is a digital loopback toward the CO as shown in Figure A-4. The loopbacks are initiated by the DDS latching loopback codes for NEI Position 1 (N1000001) for FT1 #1 or NEI Position 2 (N100001) for FT1 Repeater # 2. ...

  • ADTRAN T200 FNID - page 16

    A-3 Section 61245201L1-5, Issue 3 61245201L1-5C 3. LOOPBACK ACTIVATION/DEACTIVATION This section describes loopback activation and deactivation methods for the ADTRAN Fractional T1 system. Loopback activation and deactivation is controlled with the push-button located on the front panel, through craft interface, or latching loopback codes. Both the ...

メーカー ADTRAN カテゴリー Network Card

ADTRAN T200 FNIDのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- T200 FNIDの取扱説明書
- ADTRANの製品カード
- パンフレット
- またはADTRAN T200 FNIDの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、ADTRAN T200 FNIDの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、ADTRAN T200 FNIDの取り付け説明書、サービスマニュアル、簡易説明書、またはADTRAN T200 FNIDのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、ADTRAN T200 FNIDの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

ADTRAN T200 FNIDデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがADTRAN T200 FNIDを使用するのを助ける技術的文書のことです。説明書は通常、全てのADTRAN T200 FNIDユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

ADTRANの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. ADTRAN T200 FNIDの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははADTRAN T200 FNIDの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。ADTRAN T200 FNIDに関してこのドキュメントで見つけることができる全てのヒントの目次
3. ADTRAN T200 FNIDデバイスの基本機能を使うにあたってのヒント。 ADTRAN T200 FNIDのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。ADTRAN T200 FNIDに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるADTRAN T200 FNIDのメーカー/サービスへの連絡先に関する情報。

ADTRAN T200 FNIDについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもADTRAN T200 FNIDの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがADTRAN T200 FNIDで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)