Omron BUM100Sの取扱説明書

16ページ 1.03 mb
ダウンロード

ページに移動 of 16

Summary
  • Omron BUM100S - page 1

    1 Do not use this product in applications which require an extremely high degree of reliability and safety , such as those listed below . (This product is designed and manufactured for use for OA equipment such as personal computers.) • Medical equipment or system that may cause death dir ectly • Applications that directly af fect the safety of ...

  • Omron BUM100S - page 2

    2 When the battery is dead, replace it immediately or stop using the unit. • Continuing to use the unit may cause a fire. Do not place objects on the unit, and do not drop metal objects onto the unit. • Doing so may cause distortion/damage to the case or a failure of the internal circuit, and may cause a fir e. Do not use the product in a close ...

  • Omron BUM100S - page 3

    3 Notes Charge the battery (for at least 24 hours) immediately after purchase. • If you do not use the unit for a long time after pur chase, the battery per for mance may deteriorate and it may become unusable. • The battery can be charged once the AC input plug of the UPS is connected to a wall outlet (commercial power). When storing the UPS, ...

  • Omron BUM100S - page 4

    4 1-2 Checking the accessories Make sure that all accessories ar e included and that there is no external damage. If you notice any defects, immediately contact the shop of purchase. 1. Instruction manual (Japanese/English edition) .... 1 2. Battery connection cable + Cable clamps (BUM100S only) ............................................. 1 set 3 ...

  • Omron BUM100S - page 5

    5 2-1 Installation Install the additional battery unit. Do not use this unit in any position other than the correct positions indicated in the illustration below . Correct positions - バッテリ  交換 バッテリ  増設 ブザー停止/テスト 電源出力 バイパス 運転 BU150SW - バッテリ  交換 バッテリ  増設 ブ? ...

  • Omron BUM100S - page 6

    6  ● For BUM300S Correct Positions Be careful not to get your fingers caught when arranging the unit. Caster at the bottom may be removed when sitting horizontally. Incorrect Positions BATTRY UNIT BATTRY UNIT * Do not place the UPS or the additional batter y unit on top of each other . The upper unit ma y f all down by vibr ation etc. - バッ? ...

  • Omron BUM100S - page 7

    7 2-2 Connecting the additional battery unit ( BUM100S/150S/300S ) Y ou can add only one additional battery unit. 2-2-1 BUM100S connection procedure / Connectable UPS: BU100SW/BU1002SW (1) Remove the cover of the additional battery connector on the back of the UPS. Also remove the scr ews on the lower part of the signal card expansion slot cover . ...

  • Omron BUM100S - page 8

    8 Additional battery signal connection Additional battery connection Additional battery signal connection Additional battery connection ON     OFF Overcurrent protection switch Battery connection cable 2-2-3 BUM300S connection procedure / Connectable UPS : BU3002SW (1) Connect the battery connection cable to the batter y connectors on the rea ...

  • Omron BUM100S - page 9

    9 3. Replacing the battery The battery can be replaced while the UPS is stopped. (power supply output stopped) Caution When an additional battery unit (BUM100S/BUM150S/BUM300S) is connected to the UPS, replace the UPS battery when replacing the batteries of the additional battery unit. Y ou cannot perfor m batter y replacement of the additional bat ...

  • Omron BUM100S - page 10

    10 3. Remove (anti-clockwise rotation) the 2 scr ews that hold the plate cover in place. ➀ Pull the plate cover towar ds you ➁ , and lift it up to remove it. ➂ 4. Remove both battery packs by pulling on the pullout label at the bottom of each battery pack. Use the red tape on top of the battery pack, which is 10 cm from the inner edge of the ...

  • Omron BUM100S - page 11

    11 Tighten the 2 screws. 1 2 7. Attach the front panel. Insert the tab at the bottom of the front panel into the hole in the main body ➀ , and push the plate cover towards the main body . ➁ Use a screwdriver to secur ely tighten (clockwise) the 2 screws at the top of the fr ont panel. 6. Securely connect the connectors. ➀ Secure the connector ...

  • Omron BUM100S - page 12

    12 Additional battery unit (BUM300S) r eplacement procedur e For information on UPS battery replacement pr ocedure, r efer to the UPS instruction manual. 1. Use a screwdriver to loosen ( anti-clockwise r otation ) the 4 screws on the fr ont panel of the additional battery unit until they turn freely . BATTRY UNIT 1 B AT TRY UN IT Loosen the 4 screw ...

  • Omron BUM100S - page 13

    13 4. Remove the 4 battery packs by pulling on the pullout label at the bottom of each battery pack. Use the red tape on top of the battery pack, which is 10 cm from the inner edge of the battery , to gauge how much further you need to pull the batter y to remove it. Hold the battery securely with both hands so as not to drop it. Caution Do not hol ...

  • Omron BUM100S - page 14

    14 6. Securely connect the connectors. ➀ Secure the connectors to the plate cover . ➁ Y ou may hear a “pop” sound when you connect the battery if it is replaced after the unit’s operation is stopped, but this sound is not abnormal. If you cannot secure a connector to the plate cover , the connector is not completely connected. Connect the ...

  • Omron BUM100S - page 15

    15 <After replacing the battery during operation...> Press the beep stop/test button for 5 to 10 seconds, to perform a self-diagnostic test. Normal operation r esumes after the test for about 10 second. If the beeping sounds, the beeping stops at the first pr ess of the button and starts test in the second press of the button. If the battery ...

  • Omron BUM100S - page 16

    16 K1L-D-05096C Dimensions 395 15 91 26 402 285 φ15 φ25 224 13 10 64 145 M 4 screw BUM100S <Unit: mm / T olerance: ± 1mm> ● BUM100S/BUM150S ● BUM300S 21 509 329 402 299 117 66 28 432 56 178 286 213 3 99 BUM300S <Unit: mm / T olerance: ± 1mm> Power cable (approximately 1.8m) 360 ...

メーカー Omron カテゴリー Marine Instruments

Omron BUM100Sのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- BUM100Sの取扱説明書
- Omronの製品カード
- パンフレット
- またはOmron BUM100Sの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Omron BUM100Sの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Omron BUM100Sの取り付け説明書、サービスマニュアル、簡易説明書、またはOmron BUM100Sのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Omron BUM100Sの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Omron BUM100Sデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがOmron BUM100Sを使用するのを助ける技術的文書のことです。説明書は通常、全てのOmron BUM100Sユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Omronの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Omron BUM100Sの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははOmron BUM100Sの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Omron BUM100Sに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Omron BUM100Sデバイスの基本機能を使うにあたってのヒント。 Omron BUM100Sのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Omron BUM100Sに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるOmron BUM100Sのメーカー/サービスへの連絡先に関する情報。

Omron BUM100Sについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもOmron BUM100Sの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがOmron BUM100Sで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)