-
KitchenAid W10189714A - page 1
MICROWAVE HOOD COMBINATION INSTALLATION INSTRUCTIONS MICROWAVE HOOD COMBINATION SAFETY This pro duct is suitable for us e above electric or gas cooking pr oducts up to and including 30" (76.2 c m) wide. See “Installati on Requirements” section for further notes. These installation inst ru ctions cover dif feren t models. The appearance of ...
-
KitchenAid W10189714A - page 2
2 INSTALLATION REQUIREMENTS The microwave oven is set for r ecirculation installation. For exte rnal (wall or roof) venting, se e “V enting Design Specificatio ns” sect ion. Tools and Parts T ools Needed Gather the r equir ed tools and part s befor e starting installation. Read and follow the instructio ns provided with a ny tools listed here. ...
-
KitchenAid W10189714A - page 3
3 Installation Dimensions NOTE: The grounded 3 prong outlet must be inside the upper cabinet. See “Electrical Requir ements” section. * 33" (83.2 cm) is typical for 69" (175.3 cm) inst allation height. Exact dimension may vary depending on type of range/cooktop below . Product Dimensions Electrical Requirements Observe all governing c ...
-
KitchenAid W10189714A - page 4
4 INSTALLATION INSTRUCTIONS Remove Mounting Plate NOTE: T o avoid possible damage to the work surface, cover the work surface. 1. Remove any remaining co ntents from the microwav e oven cavity . 2. Remove the mounting plate by peeling off the strips of tape that attach it to the back of the microw ave oven, and set the mounting plate aside. 3. T ap ...
-
KitchenAid W10189714A - page 5
5 3. When the vent de flector is a s far back as it can easily sl ide, flip it so that the wide side is to the back of the microwave oven , and the narrow side (with holes) is down. The vent deflector holes should align with mounti ng holes in the vent opening, as shown in inset. 4. Secur e vent deflector with 2 mounti ng screws (1 on eac h end). 5 ...
-
KitchenAid W10189714A - page 6
6 Locate Wall Stud(s) NOTE: If no wall studs exist within the cabin et opening, do not install the microwave oven. See illustrat ions in “Possible W all Stud Configurati ons.” 1. Using a stud finder , locate the ed ges of the wall stud(s) wit hin the opening. 2. Mark the center of e ach stud, and draw a plumb line down each stud center . See il ...
-
KitchenAid W10189714A - page 7
7 Mark Rear Wall The microwave oven must be inst alled on a minimum of 1 wall stud, preferably 2 , using a minimum of 1 lag screw , preferably 2. 1. Using measuring tape, find an d clearly mark the vertical centerlin e of the open ing. A. Centerline 2. With the suppor t tabs facing f orward (se e illustration s in “Possible W all Stud Configurati ...
-
KitchenAid W10189714A - page 8
8 Attach Mounting Plate to Wall NOTE: Secure the mounting plate to the wall at both bottom cor ner holes drill ed into the wa ll studs and/or drywall using either 1/4-20 x 3" r ound-he ad bolts and toggle nuts or 1 /4 x 2" lag screws. Refer to illustrat ions in “Possible W all Stud Configu rations” in “Locate W all Stud(s)” sectio ...
-
KitchenAid W10189714A - page 9
9 5. Cut the 1 ¹⁄₂ " (3.8 cm) diameter hole at the circu lar shaded ar ea “G” on the template. This hole is for the power supply cor d. NOTE: If upper cabinet is metal, the supply cord bushing needs to be installed ar ound the supply cor d hole, as shown. 6. Drill 3/8" (10 mm) holes at poin ts “D” and “E” on the template. ...
-
KitchenAid W10189714A - page 10
10 For Roof V enting Installation Only 1. Insert damper assembly through th e cabinet cutou t so that the long tab of the damper assembly slid es into the slot on the left side of the damper vent opening, as shown. Then secu re with mounting scr ew . NOTE: The screw cannot be instal led if the damper assembly is not positioned as shown. 2. Connect ...
-
KitchenAid W10189714A - page 11
11 VENTING DESIGN SPECIFICATIONS This section is i ntended fo r ar chitectural designer and builder/contractor refer ence only . NOTES: ■ V ent materials needed for instal lation are not pr ovided with microw ave hood. ■ W e do not recommend using a flexible metal vent. ■ T o avoid possible product damage, be sur e to vent air outside, unless ...
-
KitchenAid W10189714A - page 12
Recommended V ent Length A 3 ¹⁄₄ " x 10 " (8.3 x 25.4 cm) r ectangular or 6 " (15.2 cm) ro und vent should be used. The total lengt h of the vent sys tem includin g straight vent, elbow(s), transitions and wall or roof caps must not exc eed the equivalent of 140 ft (42.7 m) for eit her type of vent. See “Recommended Standar d ...
KitchenAid W10189714Aについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもKitchenAid W10189714Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKitchenAid W10189714Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。