Smeg SE706S3の取扱説明書

16ページ 関係なし
ダウンロード

ページに移動 of 16

Summary
  • Smeg SE706S3 - page 1

    Contents 1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________ 22 2. POSITIONING OF HOB ___________________________________ 24 3. ELECTRICAL CONNECTI ON ______________________________ 26 4. GAS CONNECTION ______________________________________ 27 5. ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 29 6. FINAL OPERATIONS ______________________ ...

  • Smeg SE706S3 - page 2

    Introduction 1. INSTRUCTIONS FOR SAFE AND PR OPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP TH E SERIES OF NOZZLES SUPP ...

  • Smeg SE706S3 - page 3

    Introduction THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER TH E CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE CASING. DO NOT PUT PANS WITHOUT PERFECTLY SMOO ...

  • Smeg SE706S3 - page 4

    Instructions for the installer 24 2. POSITIONI NG OF HOB The following oper ation requires buildi ng and/or carp entry work so must be carried out by a competent tradesman. Installation can be carried out on var ious materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). Never use silico ...

  • Smeg SE706S3 - page 5

    Instructions for the installer 25 In case of installation on a holl ow compartment with doors, a separating panel has to be pl aced under the hob. Keep a minimum d istance of 10 mm betwee n the bottom of the unit and th e panel surface. The panel has to be easily removable to allow acces s in the event of technical service. ...

  • Smeg SE706S3 - page 6

    Instructions for the installer 26 3. ELECTRICAL CONNECTION Make sure that the voltage and capacit y of the power l ine conform to the data shown on the plate locat ed under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the curr ent electrical sys ...

  • Smeg SE706S3 - page 7

    Instructions for the installer 27 4. GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the prov isions defi ned by standard regulations in force. To facilitate connection, fitting A on the r ear of the appliance may be adjusted laterally. For this purpose, loos en hexagon nut B ...

  • Smeg SE706S3 - page 8

    Instructions for the installer 28 4.1 Connection to LPG Use a pressure regulator and make the con nection to the tank according to the provisions of stand ard s regulations in force. Make sure that feed pressure conforms to the lev els shown in the table in paragraph “ 5. 2 Regulation for LPG ”. 4.2 Ventilation of rooms The hob may be installed ...

  • Smeg SE706S3 - page 9

    Instructions for the installer 29 5. AD APT A TION T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar. For functioning with other ty pes of gas the nozzles must be replaced and the primary air ad ...

  • Smeg SE706S3 - page 10

    Instructions for the installer 30 5.2 Regulation for LPG Loosen screw A and push supp ort B all the way. Use a double head wrench to remove nozzle C a nd assemble the suitable one, follow ing the instructions indicated in the referenc e charts, with respect to the type of gas to use. The screwing t orque of the nozzle shoul d never exceed 3 Nm . Re ...

  • Smeg SE706S3 - page 11

    Instructions for the installer 31 5.3 Regulation for natural gas The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar. To allow the unit to work wit h this type of gas, perform the same operations described in parag raph “ 5.2 Regula tion for LPG ”, but choose the nozzles and regulate the primary ai r for natural gas, a ...

  • Smeg SE706S3 - page 12

    Instructions for the installer 32 6. FINAL OPERA TIONS Having carried out the abov e adjustments, reassemble the applianc e following, backwards, the inst ructions in paragraph “ 5.1 Removing the hob ”. 6.1 Regulation of minimum for natural gas Replace the co mponents on the burner and slide the knobs on the gas tap pins. Light the burner and s ...

  • Smeg SE706S3 - page 13

    Instructions for the installer 33 6.3 Arrangement of burners on hob BURNERS 1 Auxiliary 2 Semi-rapid 3 Average rapid 4 Large rapid 5-6 Triple crown 7 Double crown 6.4 Lubrication of gas taps After a while, the gas tap may become hard to turn or lock. If this happens, it has to be cleaned inside and re-greased. This must be done by a qualified techn ...

  • Smeg SE706S3 - page 14

    Insructions for the user 34 7. USING THE HOB Make sure that the fl ame-baffle crowns, the caps and the grid have been assembled correctly. Grid C (supplied) should be used for "woks" (Chinese pots). Adapter B (supplied) is to be used for small vessels. 7.1 Ignition of the burners with safety device For each knob the c orresponding burner ...

  • Smeg SE706S3 - page 15

    Insructions for the user 7.3 Diameter of containers BURNERS Ø min. e max. (in cm) 1 Auxiliary 7-18 2 Semi-rapid 10-24 12-24 3 Average rapid 14-28 4 Large rapid 22-26 5-6 Triple crown 12-34 7 Double crown 7.4 Using a griddle plate A few precautions are necessary if you wish to use a griddl e plate: • leave a gap of at le ast 160 mm between the ed ...

  • Smeg SE706S3 - page 16

    Insructions for the user 36 8. CLEANING AND MAINTENANCE NEVER USE A STEAM JET TO CLEAN THE APPLIANCE. Before any intervention, disconnect the p ower supply of the device. 8.1 Cleaning Clean the cooking top regularly every time you use it, obv iously after it has cooled. 8.1.1 Regular daily cleaning of the hob In order to clean and preserve the su r ...

メーカー Smeg カテゴリー Stove

Smeg SE706S3のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SE706S3の取扱説明書
- Smegの製品カード
- パンフレット
- またはSmeg SE706S3の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Smeg SE706S3の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Smeg SE706S3の取り付け説明書、サービスマニュアル、簡易説明書、またはSmeg SE706S3のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Smeg SE706S3の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Smeg SE706S3デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSmeg SE706S3を使用するのを助ける技術的文書のことです。説明書は通常、全てのSmeg SE706S3ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Smegの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Smeg SE706S3の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSmeg SE706S3の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Smeg SE706S3に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Smeg SE706S3デバイスの基本機能を使うにあたってのヒント。 Smeg SE706S3のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Smeg SE706S3に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSmeg SE706S3のメーカー/サービスへの連絡先に関する情報。

Smeg SE706S3についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSmeg SE706S3の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSmeg SE706S3で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)