English dropdown-ico

Manual Smeg SE706S3

16 pages Not applicable
Download

Go to site of 16

Summary
  • Smeg SE706S3 - page 1

    Contents 1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________ 22 2. POSITIONING OF HOB ___________________________________ 24 3. ELECTRICAL CONNECTI ON ______________________________ 26 4. GAS CONNECTION ______________________________________ 27 5. ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 29 6. FINAL OPERATIONS ______________________ ...

  • Smeg SE706S3 - page 2

    Introduction 1. INSTRUCTIONS FOR SAFE AND PR OPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP TH E SERIES OF NOZZLES SUPP ...

  • Smeg SE706S3 - page 3

    Introduction THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER TH E CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE CASING. DO NOT PUT PANS WITHOUT PERFECTLY SMOO ...

  • Smeg SE706S3 - page 4

    Instructions for the installer 24 2. POSITIONI NG OF HOB The following oper ation requires buildi ng and/or carp entry work so must be carried out by a competent tradesman. Installation can be carried out on var ious materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). Never use silico ...

  • Smeg SE706S3 - page 5

    Instructions for the installer 25 In case of installation on a holl ow compartment with doors, a separating panel has to be pl aced under the hob. Keep a minimum d istance of 10 mm betwee n the bottom of the unit and th e panel surface. The panel has to be easily removable to allow acces s in the event of technical service. ...

  • Smeg SE706S3 - page 6

    Instructions for the installer 26 3. ELECTRICAL CONNECTION Make sure that the voltage and capacit y of the power l ine conform to the data shown on the plate locat ed under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the curr ent electrical sys ...

  • Smeg SE706S3 - page 7

    Instructions for the installer 27 4. GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the prov isions defi ned by standard regulations in force. To facilitate connection, fitting A on the r ear of the appliance may be adjusted laterally. For this purpose, loos en hexagon nut B ...

  • Smeg SE706S3 - page 8

    Instructions for the installer 28 4.1 Connection to LPG Use a pressure regulator and make the con nection to the tank according to the provisions of stand ard s regulations in force. Make sure that feed pressure conforms to the lev els shown in the table in paragraph “ 5. 2 Regulation for LPG ”. 4.2 Ventilation of rooms The hob may be installed ...

  • Smeg SE706S3 - page 9

    Instructions for the installer 29 5. AD APT A TION T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar. For functioning with other ty pes of gas the nozzles must be replaced and the primary air ad ...

  • Smeg SE706S3 - page 10

    Instructions for the installer 30 5.2 Regulation for LPG Loosen screw A and push supp ort B all the way. Use a double head wrench to remove nozzle C a nd assemble the suitable one, follow ing the instructions indicated in the referenc e charts, with respect to the type of gas to use. The screwing t orque of the nozzle shoul d never exceed 3 Nm . Re ...

  • Smeg SE706S3 - page 11

    Instructions for the installer 31 5.3 Regulation for natural gas The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar. To allow the unit to work wit h this type of gas, perform the same operations described in parag raph “ 5.2 Regula tion for LPG ”, but choose the nozzles and regulate the primary ai r for natural gas, a ...

  • Smeg SE706S3 - page 12

    Instructions for the installer 32 6. FINAL OPERA TIONS Having carried out the abov e adjustments, reassemble the applianc e following, backwards, the inst ructions in paragraph “ 5.1 Removing the hob ”. 6.1 Regulation of minimum for natural gas Replace the co mponents on the burner and slide the knobs on the gas tap pins. Light the burner and s ...

  • Smeg SE706S3 - page 13

    Instructions for the installer 33 6.3 Arrangement of burners on hob BURNERS 1 Auxiliary 2 Semi-rapid 3 Average rapid 4 Large rapid 5-6 Triple crown 7 Double crown 6.4 Lubrication of gas taps After a while, the gas tap may become hard to turn or lock. If this happens, it has to be cleaned inside and re-greased. This must be done by a qualified techn ...

  • Smeg SE706S3 - page 14

    Insructions for the user 34 7. USING THE HOB Make sure that the fl ame-baffle crowns, the caps and the grid have been assembled correctly. Grid C (supplied) should be used for "woks" (Chinese pots). Adapter B (supplied) is to be used for small vessels. 7.1 Ignition of the burners with safety device For each knob the c orresponding burner ...

  • Smeg SE706S3 - page 15

    Insructions for the user 7.3 Diameter of containers BURNERS Ø min. e max. (in cm) 1 Auxiliary 7-18 2 Semi-rapid 10-24 12-24 3 Average rapid 14-28 4 Large rapid 22-26 5-6 Triple crown 12-34 7 Double crown 7.4 Using a griddle plate A few precautions are necessary if you wish to use a griddl e plate: • leave a gap of at le ast 160 mm between the ed ...

  • Smeg SE706S3 - page 16

    Insructions for the user 36 8. CLEANING AND MAINTENANCE NEVER USE A STEAM JET TO CLEAN THE APPLIANCE. Before any intervention, disconnect the p ower supply of the device. 8.1 Cleaning Clean the cooking top regularly every time you use it, obv iously after it has cooled. 8.1.1 Regular daily cleaning of the hob In order to clean and preserve the su r ...

Manufacturer Smeg Category Stove

Documents that we receive from a manufacturer of a Smeg SE706S3 can be divided into several groups. They are, among others:
- Smeg technical drawings
- SE706S3 manuals
- Smeg product data sheets
- information booklets
- or energy labels Smeg SE706S3
All of them are important, but the most important information from the point of view of use of the device are in the user manual Smeg SE706S3.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Smeg SE706S3, service manual, brief instructions and user manuals Smeg SE706S3. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Smeg SE706S3.

Similar manuals

A complete manual for the device Smeg SE706S3, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Smeg SE706S3 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Smeg SE706S3.

A complete Smeg manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Smeg SE706S3 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Smeg SE706S3, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Smeg SE706S3, that we can find in the current document
3. Tips how to use the basic functions of the device Smeg SE706S3 - which should help us in our first steps of using Smeg SE706S3
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Smeg SE706S3
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Smeg SE706S3 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Smeg SE706S3?

Use the form below

If you did not solve your problem by using a manual Smeg SE706S3, ask a question using the form below. If a user had a similar problem with Smeg SE706S3 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)