National Instruments FP-1600の取扱説明書

19ページ 1.01 mb
ダウンロード

ページに移動 of 19

Summary
  • National Instruments FP-1600 - page 1

    FP-1600 FieldPoint Quick Start Guide 1 Install the Network Module 1 Panel Mount DIN Rail Mount A. Unlock rail clip. A. Unlock rail clip. · Network Module · Mounting Hardware (DIN rail or panel mount accessory) · T erminal Base(s) · I/O Module(s) · Power Supply · FieldPoint Software CD · Accessories: Ethernet cable, screwdriver What Y ou Need ...

  • National Instruments FP-1600 - page 2

    B. Hook lip on back of module onto top of DIN rail, press down, and snap into place. B. Snap panel mount accessory (which you can order separately) onto module. Panel Mount DIN Rail Mount NOTE: Do not use spliced DIN rails. Use only a single DIN rail. C. Slide module into position and lock rail clip. C. Lock rail clip. D. Use template that came wit ...

  • National Instruments FP-1600 - page 3

    Install the T erminal Base(s) CAUTION : T erminal bases must be connected to the network module before applying power to the module. Do not connect or disconnect terminal bases while power is applied to the network module. 2 DIN Rail Mount A. Unlock rail clip. B. Press base onto rail. Panel Mount A. Use template that came with your accessory to dri ...

  • National Instruments FP-1600 - page 4

    DIN Rail Mount Panel Mount D. Repeat for each terminal base, up to nine for each network module in most cases. Y ou can use one or two extender cables (which you can order separately) if your FieldPoint bank is too long for your available space. E. Place protective cover on last base, and install rail locks at each end. C. Slide into position and l ...

  • National Instruments FP-1600 - page 5

    3 Install the I/O Module(s) A. Align slots on module with guide rails on base, and press onto base until terminal base’ s latch locks the module in place. B. Repeat for each I/O module. It does not matter where you install each I/O module, except for these types of situations: · · · · If you plan to cascade power between any I/O modules using ...

  • National Instruments FP-1600 - page 6

    Do not use a cable longer than 100 m. If you are using a 100 Mbps Ethernet, National Instruments recommends using a Category 5 shielded twisted-pair Ethernet. If you need to build your own cable, refer to the FP-1600 User Manual for cabling details. 5 Wire Power to Y our FieldPoint System A. Connect 11-30 VDC power supply leads to V and C terminals ...

  • National Instruments FP-1600 - page 7

    CAUTION: Cascading power from neighboring bases or network modules defeats isolation between cascaded modules. 15 16 V 31 32 C V 1 3 2 C 17 18 CAUTION: Cascading power defeats isolation. Shades of gray indicate different voltage potentials. Separate Power Supply (Recommended) Cascaded Power (Reduces Isolation) FP-1600 FP-AI-100 FP-AO-200 FP-RL Y -4 ...

  • National Instruments FP-1600 - page 8

    6 Connect to Field Devices Use each I/O module’ s operating instructions, or the diagram under its removable label, to help you connect your field devices. FP-AI-110 8 Channel, 16-Bit Analog Input Module Highlights Overview FP-AI-110 Self-P owered Floating Sensor 15 32 Loop-P owered Sensor 17 2 I Sensor Channel 0 V Sensor Channel 7 To P o w e r S ...

  • National Instruments FP-1600 - page 9

    7 Power Up Y our FieldPoint System CAUTION: T erminal bases must be connected to the FP-1600 before power is applied to the FP-1600. Plug in each power supply to your FieldPoint bank. Y ou should see all except the ST A TUS and PROCESS LEDs flash once, and the POWER LED come on and stay on. After a few seconds, the POWER and READY LEDs should be li ...

  • National Instruments FP-1600 - page 10

    8 Install the FieldPoint Software A. Close all other applications. If you plan to install National Instruments development software such as Lookout, LabVIEW , or Measurement Studio, install them before you install the FieldPoint software. B. Insert the FieldPoint software CD and follow the onscreen instructions. 9 Verify the Installation A. Select ...

  • National Instruments FP-1600 - page 11

    C. In the Comm Resource Configuration dialog box, select Ethernet as the T ype . D. Click Browse , select the FP-1600, and click the Device Properties button. 11 fpoint cd.qxd 11/13/00 1:24 PM Page 11 ...

  • National Instruments FP-1600 - page 12

    E. In the FP-1600 Properties box, enter values for the IP address , Subnet mask , and Time server IP . Y ou might also want to enter a comment to help you identify the FP-1600 module. • IP address is the address of the FP-1600 on the network. • Subnet mask is the mask that is applied to the IP address that the device uses to find other devices ...

  • National Instruments FP-1600 - page 13

    If your modules are not listed, check the cable and connections and make sure the modules are all powered on. If you still have problems, refer to your FP-1600 user manual for troubleshooting information. I. Select an input module and click on the start monitoring button to view live data. J. Select an output channel and click on the write button t ...

  • National Instruments FP-1600 - page 14

    10 Configure I/O Modules A. Right-click on the device name in FieldPoint Explorer and select Edit this Device from the pop-up menu. B. Click on the Channel Configuration button to bring up the Channel Configuration dialog box. C. Select the type of channel to show , then select the channel(s) that you want to change. T o select more than one channe ...

  • National Instruments FP-1600 - page 15

    D. Set the range and output values of the selected channel(s). E. Set the attributes for the selected channel(s) by selecting the attribute and entering the desired value. F . Send commands to the selected channel(s) by choosing a command and value and clicking on Send . G. Repeat this procedure for each channel you want to configure. H. Click on t ...

  • National Instruments FP-1600 - page 16

    11 Where to Go from Here After you get your hardware up and running, you might want to implement features such as power -up defaults or network watchdog settings. Refer to your FP-1600 user manual or online help for information about features, configuration, application development, and troubleshooting. 16 fpoint cd.qxd 11/13/00 1:24 PM Page 16 ...

  • National Instruments FP-1600 - page 17

    FP-1600 Specifications Network interface .................... 10BaseT and 100BaseTX Ethernet Compatibility ........................ IEEE 802.3 Communications rate .................1 0 Mbps, 100 Mbps, autonegotiated Cabling distance .....................1 0 0m Power supply range ..................1 1t o3 0V D C Power consumption ..................7W ...

  • National Instruments FP-1600 - page 18

    4.31 [109.5] 3.60 [91.44] 4.22 [107.19] Mechanical Dimensions Dimensions are given in inches [millimeters]. 18 fpoint cd.qxd 11/13/00 1:24 PM Page 18 ...

  • National Instruments FP-1600 - page 19

    United States 512 795-8248 Australia 03 9879 5166, Austria 0662 45 79 90 0, Belgium 02 757 00 20, Brazil 011 284 5011, Canada (Calgary) 403 274 9391, Canada (Ontario) 905 785 0085, Canada (Québec) 514 694 8521, China 0755 3904939, Denmark 45 76 26 00, Finland 09 725 725 11, France 01 48 14 24 24, Germany 089 741 31 30, Greece 30 1 42 96 427, Hong ...

メーカー National Instruments カテゴリー Computer Hardware

National Instruments FP-1600のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- FP-1600の取扱説明書
- National Instrumentsの製品カード
- パンフレット
- またはNational Instruments FP-1600の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、National Instruments FP-1600の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、National Instruments FP-1600の取り付け説明書、サービスマニュアル、簡易説明書、またはNational Instruments FP-1600のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、National Instruments FP-1600の製品を使用するにあたって最も人気のある説明書を閲覧できます。

National Instruments FP-1600デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがNational Instruments FP-1600を使用するのを助ける技術的文書のことです。説明書は通常、全てのNational Instruments FP-1600ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

National Instrumentsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. National Instruments FP-1600の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははNational Instruments FP-1600の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。National Instruments FP-1600に関してこのドキュメントで見つけることができる全てのヒントの目次
3. National Instruments FP-1600デバイスの基本機能を使うにあたってのヒント。 National Instruments FP-1600のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。National Instruments FP-1600に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるNational Instruments FP-1600のメーカー/サービスへの連絡先に関する情報。

National Instruments FP-1600についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもNational Instruments FP-1600の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがNational Instruments FP-1600で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)