English dropdown-ico

Manual National Instruments FP-1600

19 pages 1.01 mb
Download

Go to site of 19

Summary
  • National Instruments FP-1600 - page 1

    FP-1600 FieldPoint Quick Start Guide 1 Install the Network Module 1 Panel Mount DIN Rail Mount A. Unlock rail clip. A. Unlock rail clip. · Network Module · Mounting Hardware (DIN rail or panel mount accessory) · T erminal Base(s) · I/O Module(s) · Power Supply · FieldPoint Software CD · Accessories: Ethernet cable, screwdriver What Y ou Need ...

  • National Instruments FP-1600 - page 2

    B. Hook lip on back of module onto top of DIN rail, press down, and snap into place. B. Snap panel mount accessory (which you can order separately) onto module. Panel Mount DIN Rail Mount NOTE: Do not use spliced DIN rails. Use only a single DIN rail. C. Slide module into position and lock rail clip. C. Lock rail clip. D. Use template that came wit ...

  • National Instruments FP-1600 - page 3

    Install the T erminal Base(s) CAUTION : T erminal bases must be connected to the network module before applying power to the module. Do not connect or disconnect terminal bases while power is applied to the network module. 2 DIN Rail Mount A. Unlock rail clip. B. Press base onto rail. Panel Mount A. Use template that came with your accessory to dri ...

  • National Instruments FP-1600 - page 4

    DIN Rail Mount Panel Mount D. Repeat for each terminal base, up to nine for each network module in most cases. Y ou can use one or two extender cables (which you can order separately) if your FieldPoint bank is too long for your available space. E. Place protective cover on last base, and install rail locks at each end. C. Slide into position and l ...

  • National Instruments FP-1600 - page 5

    3 Install the I/O Module(s) A. Align slots on module with guide rails on base, and press onto base until terminal base’ s latch locks the module in place. B. Repeat for each I/O module. It does not matter where you install each I/O module, except for these types of situations: · · · · If you plan to cascade power between any I/O modules using ...

  • National Instruments FP-1600 - page 6

    Do not use a cable longer than 100 m. If you are using a 100 Mbps Ethernet, National Instruments recommends using a Category 5 shielded twisted-pair Ethernet. If you need to build your own cable, refer to the FP-1600 User Manual for cabling details. 5 Wire Power to Y our FieldPoint System A. Connect 11-30 VDC power supply leads to V and C terminals ...

  • National Instruments FP-1600 - page 7

    CAUTION: Cascading power from neighboring bases or network modules defeats isolation between cascaded modules. 15 16 V 31 32 C V 1 3 2 C 17 18 CAUTION: Cascading power defeats isolation. Shades of gray indicate different voltage potentials. Separate Power Supply (Recommended) Cascaded Power (Reduces Isolation) FP-1600 FP-AI-100 FP-AO-200 FP-RL Y -4 ...

  • National Instruments FP-1600 - page 8

    6 Connect to Field Devices Use each I/O module’ s operating instructions, or the diagram under its removable label, to help you connect your field devices. FP-AI-110 8 Channel, 16-Bit Analog Input Module Highlights Overview FP-AI-110 Self-P owered Floating Sensor 15 32 Loop-P owered Sensor 17 2 I Sensor Channel 0 V Sensor Channel 7 To P o w e r S ...

  • National Instruments FP-1600 - page 9

    7 Power Up Y our FieldPoint System CAUTION: T erminal bases must be connected to the FP-1600 before power is applied to the FP-1600. Plug in each power supply to your FieldPoint bank. Y ou should see all except the ST A TUS and PROCESS LEDs flash once, and the POWER LED come on and stay on. After a few seconds, the POWER and READY LEDs should be li ...

  • National Instruments FP-1600 - page 10

    8 Install the FieldPoint Software A. Close all other applications. If you plan to install National Instruments development software such as Lookout, LabVIEW , or Measurement Studio, install them before you install the FieldPoint software. B. Insert the FieldPoint software CD and follow the onscreen instructions. 9 Verify the Installation A. Select ...

  • National Instruments FP-1600 - page 11

    C. In the Comm Resource Configuration dialog box, select Ethernet as the T ype . D. Click Browse , select the FP-1600, and click the Device Properties button. 11 fpoint cd.qxd 11/13/00 1:24 PM Page 11 ...

  • National Instruments FP-1600 - page 12

    E. In the FP-1600 Properties box, enter values for the IP address , Subnet mask , and Time server IP . Y ou might also want to enter a comment to help you identify the FP-1600 module. • IP address is the address of the FP-1600 on the network. • Subnet mask is the mask that is applied to the IP address that the device uses to find other devices ...

  • National Instruments FP-1600 - page 13

    If your modules are not listed, check the cable and connections and make sure the modules are all powered on. If you still have problems, refer to your FP-1600 user manual for troubleshooting information. I. Select an input module and click on the start monitoring button to view live data. J. Select an output channel and click on the write button t ...

  • National Instruments FP-1600 - page 14

    10 Configure I/O Modules A. Right-click on the device name in FieldPoint Explorer and select Edit this Device from the pop-up menu. B. Click on the Channel Configuration button to bring up the Channel Configuration dialog box. C. Select the type of channel to show , then select the channel(s) that you want to change. T o select more than one channe ...

  • National Instruments FP-1600 - page 15

    D. Set the range and output values of the selected channel(s). E. Set the attributes for the selected channel(s) by selecting the attribute and entering the desired value. F . Send commands to the selected channel(s) by choosing a command and value and clicking on Send . G. Repeat this procedure for each channel you want to configure. H. Click on t ...

  • National Instruments FP-1600 - page 16

    11 Where to Go from Here After you get your hardware up and running, you might want to implement features such as power -up defaults or network watchdog settings. Refer to your FP-1600 user manual or online help for information about features, configuration, application development, and troubleshooting. 16 fpoint cd.qxd 11/13/00 1:24 PM Page 16 ...

  • National Instruments FP-1600 - page 17

    FP-1600 Specifications Network interface .................... 10BaseT and 100BaseTX Ethernet Compatibility ........................ IEEE 802.3 Communications rate .................1 0 Mbps, 100 Mbps, autonegotiated Cabling distance .....................1 0 0m Power supply range ..................1 1t o3 0V D C Power consumption ..................7W ...

  • National Instruments FP-1600 - page 18

    4.31 [109.5] 3.60 [91.44] 4.22 [107.19] Mechanical Dimensions Dimensions are given in inches [millimeters]. 18 fpoint cd.qxd 11/13/00 1:24 PM Page 18 ...

  • National Instruments FP-1600 - page 19

    United States 512 795-8248 Australia 03 9879 5166, Austria 0662 45 79 90 0, Belgium 02 757 00 20, Brazil 011 284 5011, Canada (Calgary) 403 274 9391, Canada (Ontario) 905 785 0085, Canada (Québec) 514 694 8521, China 0755 3904939, Denmark 45 76 26 00, Finland 09 725 725 11, France 01 48 14 24 24, Germany 089 741 31 30, Greece 30 1 42 96 427, Hong ...

Manufacturer National Instruments Category Computer Hardware

Documents that we receive from a manufacturer of a National Instruments FP-1600 can be divided into several groups. They are, among others:
- National Instruments technical drawings
- FP-1600 manuals
- National Instruments product data sheets
- information booklets
- or energy labels National Instruments FP-1600
All of them are important, but the most important information from the point of view of use of the device are in the user manual National Instruments FP-1600.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals National Instruments FP-1600, service manual, brief instructions and user manuals National Instruments FP-1600. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product National Instruments FP-1600.

Similar manuals

A complete manual for the device National Instruments FP-1600, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use National Instruments FP-1600 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of National Instruments FP-1600.

A complete National Instruments manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual National Instruments FP-1600 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the National Instruments FP-1600, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the National Instruments FP-1600, that we can find in the current document
3. Tips how to use the basic functions of the device National Instruments FP-1600 - which should help us in our first steps of using National Instruments FP-1600
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with National Instruments FP-1600
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of National Instruments FP-1600 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning National Instruments FP-1600?

Use the form below

If you did not solve your problem by using a manual National Instruments FP-1600, ask a question using the form below. If a user had a similar problem with National Instruments FP-1600 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)