Cisco Systems 2975の取扱説明書

16ページ 1.92 mb
ダウンロード

ページに移動 of 16

Summary
  • Cisco Systems 2975 - page 1

    G ETTING S TARTED G UIDE Catalyst 2975 Switch Getting Started Guide 1 About this Guide 2 Unpac king the Switc h 3 Running Exp ress Setup 4 Managing the Switc h 5 Planning Switc h Stac ks 6 Rac k-Mounting 7 In Case of Difficulty 8 Obtaining Documentation and Submit ting a Service Req u est ...

  • Cisco Systems 2975 - page 2

    2 1 About this Guide This guide provides instructions on how to use Express Setup to ini tially configure your Cataly st switch. Also covered are swit ch management options, basic rack-mounting, stacking guidelines , port and module connection procedures, and troubleshooting help. For additional installation a nd configuration info rmation for the ...

  • Cisco Systems 2975 - page 3

    3 3 Running Express Setup When you first set up the switch, you should use Express Setup to enter the i nitial IP inform atio n. Doing this enables the swit ch to connect to local ro uters and the Internet. Y ou can then acce ss the switch through the IP a ddress f or furthe r configuration. Y ou need this equipment to set up the switch: • A PC w ...

  • Cisco Systems 2975 - page 4

    4 Step 9 V erify that the LE Ds on bo th Ethernet ports are green. W ait 30 seconds. Step 10 Launch a web browser on y our PC. Enter the IP address 10.0.0.1 in the web browser , and press Enter . Step 11 The Express Setup Basic Se ttings page appears. If i t does not appear , see the “In Case of Difficulty” section on page 14. Step 12 Enter thi ...

  • Cisco Systems 2975 - page 5

    5 Refreshing the PC IP Address After you complete Express Setup, yo u should refresh the PC IP address: • For a dynamically assigned IP address, disconnect the PC from the switch, and reconnect the PC to the network. The network DHCP server assigns a new IP address to the PC. • For a statically assigned IP address, change it to the prev iously ...

  • Cisco Systems 2975 - page 6

    6 4 Managing the Switch After you complete Express Setup and install the switch in your network, use the device manage r or other management options described in this section for further configuration. Using the Device Manager The simplest way to manage the switch is by using the devi ce manager in the switch memory . This web interface offers q ui ...

  • Cisco Systems 2975 - page 7

    7 Other Management Options Y ou can use SNM P management applications such as Cisc oW orks Small Network Management Solution (SNMS) and HP OpenV iew to configure and ma nage the switch. Y ou also can ma na ge it from an SNMP-compatible workstation that is running platforms such as HP OpenV iew or S unNet Manager . The Cisco IE2100 Series Configurat ...

  • Cisco Systems 2975 - page 8

    8 Cabling Guidelines These illustrations show the recommended s witch stack configurations with redundant stack cabling connecti ons for optimized stack bandwidth. For more configuration examples, see the hardware installation guide on Cisco.com. In this example, the stack uses the 0.5-mete r stack cable to make redundant conn ections. In this exam ...

  • Cisco Systems 2975 - page 9

    9 6 Rack-Mounting This section covers basic 19-inch rack-mounting and switch por t conn ections. For alternate mounting procedures, such as installing the switch in a 24-inch rack or on a wall, and for additional cabling information, see the hardware installation gui de on Cisco.com. Equipment That You Supply Y ou need a number -2 Phi llips screwdr ...

  • Cisco Systems 2975 - page 10

    10 Installation Warning Statements This section includes the basic installatio n warning statemen ts. T ranslations of these warning statements appear in the Regulatory Compliance and Safety Inform ation for the Catalyst 2975 Switch document on the documentation CD. War n in g T o prevent bodily injury when mounting or servicing th is unit in a rac ...

  • Cisco Systems 2975 - page 11

    11 Attaching the Brackets Use two number -8 Phillips flat-head screws to atta ch the long side of each bracket to the swit ch in one of three mounting positions. 1 Front-mounting position 3 Mid-mounting position 2 Number -8 Phillips flat-head screws 4 Rear -mounting position Catalyst 2975G S e r ie s PoE-48 Cat alyst 2975G S e r ie s PoE-48 CONSOLE ...

  • Cisco Systems 2975 - page 12

    12 Rack-Mount the Switch Use the four number -12 Phillips machine scre ws to attach the brackets to the rack. Use the b lack Phillips machine screw to atta ch the cable guide to the left or right bracket. 1 Black Phillips machine screw 4 Number -12 Phillips machine screws 2 Cable guide 5 Mid-mounting position 3 Front-mounting position 6 Rear -mount ...

  • Cisco Systems 2975 - page 13

    13 Connect the Stack Cables Use the window in the stack cable to align the connector correctly . Insert the cable into the stack port on the back of the swi tch. Secure the screws tightly . Insert the othe r end of the cable into the connector of th e other switch, and secure the screws tigh tly . Always use a Cisco-approved stack cable to connect ...

  • Cisco Systems 2975 - page 14

    14 Install SFP Modules and Conne ct to the Module Ports The switch Gigabit Ethernet SFP modules are used for c onnections to other devices. These modules are fie ld-replaceable, providing the uplink interfaces when inserted in an SFP module slot. Y ou can use any combination of SF P modules. See the switch release notes for th e list of SF P module ...

  • Cisco Systems 2975 - page 15

    15 Resetting the Switch This section describes how to reset the sw itch by rerunning Express Setup. These ar e reasons why you m ight want to reset th e switch: • Y ou installed the switch in your network a nd cannot connec t to it because yo u assigned an incorrect IP address. • Y ou want to clear all configuration from the switch and assign a ...

  • Cisco Systems 2975 - page 16

    Americas He adquarters Cisco Systems, Inc. San Jose, CA Asia Pacific Headqua rters Cisco Systems (USA) Pte. Ltd. Singapore Europe Head quarters Cisco Systems International BV Amsterdam, The Netherlands Cisco has more than 200 offices wo rldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco W ebsite at www .cisco.com/go/offices ...

メーカー Cisco Systems カテゴリー Switch

Cisco Systems 2975のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 2975の取扱説明書
- Cisco Systemsの製品カード
- パンフレット
- またはCisco Systems 2975の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco Systems 2975の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cisco Systems 2975の取り付け説明書、サービスマニュアル、簡易説明書、またはCisco Systems 2975のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco Systems 2975の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cisco Systems 2975デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco Systems 2975を使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco Systems 2975ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cisco Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cisco Systems 2975の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco Systems 2975の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco Systems 2975に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco Systems 2975デバイスの基本機能を使うにあたってのヒント。 Cisco Systems 2975のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco Systems 2975に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco Systems 2975のメーカー/サービスへの連絡先に関する情報。

Cisco Systems 2975についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCisco Systems 2975の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Systems 2975で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)