KTI Networks DH-8Tの取扱説明書

16ページ 0.08 mb
ダウンロード

ページに移動 of 16

Summary
  • KTI Networks DH-8T - page 1

    Installation Guide 10Base-T Ethernet Hub Model: DH8T DOC.980213-DH8T-K P/N: 750-0104-001 ...

  • KTI Networks DH-8T - page 2

    KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Net- works Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time to time w ...

  • KTI Networks DH-8T - page 3

    The information contained in this document is subject to change without prior no- tice. Copyright Ó KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. NetW are is a registered trademark of Novell Inc. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursua ...

  • KTI Networks DH-8T - page 4

    10BASE-T ETHERNET HUB INST ALLA TION GUIDE DOC.980214-DH8T-NK P/N:750-0104-002 ...

  • KTI Networks DH-8T - page 5

    T able of Contents Chapter 1 Introduction Introduction ............................................................................... 1 Features .................................................................................... 2 Chapter 2 Installation Installation ................................................................................. ...

  • KTI Networks DH-8T - page 6

    1. Introduction Introduction This hub is an Ethernet Hub designed for the 10Base-T environment. In terms of topology , twisted-pair Ethernet 10Base-T is defined as a star topology rather than a bus. Each port on the hub connects to only one 10Base-T device via unshielded twisted-pair (UTP) cable. The hub provides eight T wisted-Pair (TP) ports (RJ- ...

  • KTI Networks DH-8T - page 7

    Features • Network ports: 8 TP ports • Standard: T P ports conform to IEEE 802.3 10Base-T std. • Provides an additional RJ-45 jack labeled '8C' on the TP Port #8 for connecting to another hub. A standard straight-through 10Base-T UTP cable can be used for the hub-to-hub connection. • Each TP port has one Link/Rx LED to indicate th ...

  • KTI Networks DH-8T - page 8

    2. Installation Installation Y ou can place the hub in an area that meets the following specifica- tions: T emperature: 5 o to 40 o C when operating Humidity: 10% to 80% when operating Dimension: 195 mm x 129 mm x 28 mm (WxDxH) Checking AC Power One AC power adapter is contained in the hub package. Before you begin the installation, check the AC vo ...

  • KTI Networks DH-8T - page 9

    3. Making Network Connections Network Connectors The hub has 8 TP ports which are presented by 8 RJ-45 jacks. The jacks labeled 1 through 8 are permanently configured as 10Base-T MDI-X jacks and the jack labeled '8C' next the jack labeled '8' is an alternative jack which is configured as MDI jack for the TP port #8. Both jacks c ...

  • KTI Networks DH-8T - page 10

    Connecting to an Ethernet Node T o connect the hub to a 10Base-T Ethernet node, follow these steps: 1. Select an appropriate length of 10Base-T UTP cable for the connection. 2. Connect one end of the UTP cable to the MDI jack on the remote device (e.g., a PC equipped with 10Base-T Ethernet adapter). 3. Connect the other end of the UTP cable to an a ...

  • KTI Networks DH-8T - page 11

    When the number of 10Base-T nodes in your network exceeds eight, you need to connect at least two hubs to integrate all 10Base-T nodes into one network. Y ou may connect one hub to another hub by using an ordinary UTP cable as the following steps: 1. Connect one end of the UTP cable to the jack labeled '8C' of Hub A. 2. Connect the other ...

  • KTI Networks DH-8T - page 12

    When connecting more than two hubs via TP ports and UTP cables, it is important to minimize the number of hubs in any path of the network. Y ou may select one hub to serve as a primary hub to which other hubs will be connected. This will minimize the number of hubs in any path (node to node) on the network. The following figure illustrates an examp ...

  • KTI Networks DH-8T - page 13

    4. Interpreting Hub LEDs Locations of the Hub LED Indicators The hub provides the following LEDs : • One Power status LED • One Collision status LED • Eight Link and activity status LEDs. One for each TP port Interpretations Power LED The LED indicates the status of the hub's power source. Match the activity of the LED with one of the st ...

  • KTI Networks DH-8T - page 14

    Collision LED This LED indicates the collision detected by the hub. The LED is normally off and it blinks when there are collisions. As the frequency of collisions on a network increases, the blink activities (on-time) of the LED also increase. Link/Rx LED Each TP port has one Link/Rx LED to indicate the link status and receiving activities of the ...

  • KTI Networks DH-8T - page 15

    Appendix Specifications T emperature: Operating 5 o to 40 o C Storage -40 o to 70 o C Humidity: Operating 10% to 80% Storage 5% to 90% Dimension: 195mm (W) x 129mm (D) x 28mm (H) 7.7 inch (W) x 5.1 inch (D) x 1.1 inch (H) RJ-45 Jack Pin Assignments The following illustrations indicate the pin assignments of the RJ-45 jacks on the hub. Jacks '1 ...

  • KTI Networks DH-8T - page 16

    UTP Cabling Specifications The hub's TP ports support standard 10Base-T cable topologies and types, including Category 3, 4, or 5 unshielded twisted pair cable. The maximum length supported by the Ethernet is 100 meters of UTP cable. The cable, quality , distance, and connectors must comply with the EIA/TIA 568 'Commercial Building W irin ...

メーカー KTI Networks カテゴリー Network Card

KTI Networks DH-8Tのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DH-8Tの取扱説明書
- KTI Networksの製品カード
- パンフレット
- またはKTI Networks DH-8Tの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、KTI Networks DH-8Tの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、KTI Networks DH-8Tの取り付け説明書、サービスマニュアル、簡易説明書、またはKTI Networks DH-8Tのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、KTI Networks DH-8Tの製品を使用するにあたって最も人気のある説明書を閲覧できます。

KTI Networks DH-8Tデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがKTI Networks DH-8Tを使用するのを助ける技術的文書のことです。説明書は通常、全てのKTI Networks DH-8Tユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

KTI Networksの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. KTI Networks DH-8Tの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははKTI Networks DH-8Tの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。KTI Networks DH-8Tに関してこのドキュメントで見つけることができる全てのヒントの目次
3. KTI Networks DH-8Tデバイスの基本機能を使うにあたってのヒント。 KTI Networks DH-8Tのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。KTI Networks DH-8Tに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるKTI Networks DH-8Tのメーカー/サービスへの連絡先に関する情報。

KTI Networks DH-8Tについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもKTI Networks DH-8Tの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKTI Networks DH-8Tで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)