English dropdown-ico

Manual KTI Networks DH-8T

16 pages 0.08 mb
Download

Go to site of 16

Summary
  • KTI Networks DH-8T - page 1

    Installation Guide 10Base-T Ethernet Hub Model: DH8T DOC.980213-DH8T-K P/N: 750-0104-001 ...

  • KTI Networks DH-8T - page 2

    KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Net- works Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time to time w ...

  • KTI Networks DH-8T - page 3

    The information contained in this document is subject to change without prior no- tice. Copyright Ó KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. NetW are is a registered trademark of Novell Inc. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursua ...

  • KTI Networks DH-8T - page 4

    10BASE-T ETHERNET HUB INST ALLA TION GUIDE DOC.980214-DH8T-NK P/N:750-0104-002 ...

  • KTI Networks DH-8T - page 5

    T able of Contents Chapter 1 Introduction Introduction ............................................................................... 1 Features .................................................................................... 2 Chapter 2 Installation Installation ................................................................................. ...

  • KTI Networks DH-8T - page 6

    1. Introduction Introduction This hub is an Ethernet Hub designed for the 10Base-T environment. In terms of topology , twisted-pair Ethernet 10Base-T is defined as a star topology rather than a bus. Each port on the hub connects to only one 10Base-T device via unshielded twisted-pair (UTP) cable. The hub provides eight T wisted-Pair (TP) ports (RJ- ...

  • KTI Networks DH-8T - page 7

    Features • Network ports: 8 TP ports • Standard: T P ports conform to IEEE 802.3 10Base-T std. • Provides an additional RJ-45 jack labeled '8C' on the TP Port #8 for connecting to another hub. A standard straight-through 10Base-T UTP cable can be used for the hub-to-hub connection. • Each TP port has one Link/Rx LED to indicate th ...

  • KTI Networks DH-8T - page 8

    2. Installation Installation Y ou can place the hub in an area that meets the following specifica- tions: T emperature: 5 o to 40 o C when operating Humidity: 10% to 80% when operating Dimension: 195 mm x 129 mm x 28 mm (WxDxH) Checking AC Power One AC power adapter is contained in the hub package. Before you begin the installation, check the AC vo ...

  • KTI Networks DH-8T - page 9

    3. Making Network Connections Network Connectors The hub has 8 TP ports which are presented by 8 RJ-45 jacks. The jacks labeled 1 through 8 are permanently configured as 10Base-T MDI-X jacks and the jack labeled '8C' next the jack labeled '8' is an alternative jack which is configured as MDI jack for the TP port #8. Both jacks c ...

  • KTI Networks DH-8T - page 10

    Connecting to an Ethernet Node T o connect the hub to a 10Base-T Ethernet node, follow these steps: 1. Select an appropriate length of 10Base-T UTP cable for the connection. 2. Connect one end of the UTP cable to the MDI jack on the remote device (e.g., a PC equipped with 10Base-T Ethernet adapter). 3. Connect the other end of the UTP cable to an a ...

  • KTI Networks DH-8T - page 11

    When the number of 10Base-T nodes in your network exceeds eight, you need to connect at least two hubs to integrate all 10Base-T nodes into one network. Y ou may connect one hub to another hub by using an ordinary UTP cable as the following steps: 1. Connect one end of the UTP cable to the jack labeled '8C' of Hub A. 2. Connect the other ...

  • KTI Networks DH-8T - page 12

    When connecting more than two hubs via TP ports and UTP cables, it is important to minimize the number of hubs in any path of the network. Y ou may select one hub to serve as a primary hub to which other hubs will be connected. This will minimize the number of hubs in any path (node to node) on the network. The following figure illustrates an examp ...

  • KTI Networks DH-8T - page 13

    4. Interpreting Hub LEDs Locations of the Hub LED Indicators The hub provides the following LEDs : • One Power status LED • One Collision status LED • Eight Link and activity status LEDs. One for each TP port Interpretations Power LED The LED indicates the status of the hub's power source. Match the activity of the LED with one of the st ...

  • KTI Networks DH-8T - page 14

    Collision LED This LED indicates the collision detected by the hub. The LED is normally off and it blinks when there are collisions. As the frequency of collisions on a network increases, the blink activities (on-time) of the LED also increase. Link/Rx LED Each TP port has one Link/Rx LED to indicate the link status and receiving activities of the ...

  • KTI Networks DH-8T - page 15

    Appendix Specifications T emperature: Operating 5 o to 40 o C Storage -40 o to 70 o C Humidity: Operating 10% to 80% Storage 5% to 90% Dimension: 195mm (W) x 129mm (D) x 28mm (H) 7.7 inch (W) x 5.1 inch (D) x 1.1 inch (H) RJ-45 Jack Pin Assignments The following illustrations indicate the pin assignments of the RJ-45 jacks on the hub. Jacks '1 ...

  • KTI Networks DH-8T - page 16

    UTP Cabling Specifications The hub's TP ports support standard 10Base-T cable topologies and types, including Category 3, 4, or 5 unshielded twisted pair cable. The maximum length supported by the Ethernet is 100 meters of UTP cable. The cable, quality , distance, and connectors must comply with the EIA/TIA 568 'Commercial Building W irin ...

Manufacturer KTI Networks Category Network Card

Documents that we receive from a manufacturer of a KTI Networks DH-8T can be divided into several groups. They are, among others:
- KTI Networks technical drawings
- DH-8T manuals
- KTI Networks product data sheets
- information booklets
- or energy labels KTI Networks DH-8T
All of them are important, but the most important information from the point of view of use of the device are in the user manual KTI Networks DH-8T.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals KTI Networks DH-8T, service manual, brief instructions and user manuals KTI Networks DH-8T. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product KTI Networks DH-8T.

Similar manuals

A complete manual for the device KTI Networks DH-8T, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use KTI Networks DH-8T by users. Manuals are usually written by a technical writer, but in a language understandable to all users of KTI Networks DH-8T.

A complete KTI Networks manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual KTI Networks DH-8T - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the KTI Networks DH-8T, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the KTI Networks DH-8T, that we can find in the current document
3. Tips how to use the basic functions of the device KTI Networks DH-8T - which should help us in our first steps of using KTI Networks DH-8T
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with KTI Networks DH-8T
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of KTI Networks DH-8T in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning KTI Networks DH-8T?

Use the form below

If you did not solve your problem by using a manual KTI Networks DH-8T, ask a question using the form below. If a user had a similar problem with KTI Networks DH-8T it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)