-
Life Fitness 909101 ST - page 1
909101 ST LEG CURL/EXTENSION Part # 6705201 Revision: 01/9/98 1 ASSEMBL Y INSTRUCTIONS ...
-
Life Fitness 909101 ST - page 2
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the Parabody 909101 ST Leg Curl/Extension. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * Rubber mallet or hammer * 3/4” wrench * 9/16” wre ...
-
Life Fitness 909101 ST - page 3
3 PARTS LIST PART # 6697803 6662303 6662203 6705501 6523401 6699302 6700303 6698003 6698903 6698603 6698303 6625502 6693502 66373XX 66370XX 6704101 6704201 6695501 6284501 6714601 3116101 3116201 6695401 3108901 6382301 3108002 6166701 3116001 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 QTY 1 1 1 6 2 2 1 1 1 1 1 1 ...
-
Life Fitness 909101 ST - page 4
4 STEP 1: FIGURE 1 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • LOOSELY assemble LOWER CROSS SUPPORT (8) to the TOWER (1) and BENCH FRAME (7) using four 1/2 X 4” BOLTS (33), four 1/2” WASHERS (40) and four 1/2” LOCK NUTS (43). See FIGURE 1. • LOOSELY assemble UPPER CROSS SUPPORT (11) to the TOWER (1) and BENCH FRAME (7) using four 1/2 X 3” BO ...
-
Life Fitness 909101 ST - page 5
STEP 2: FIGURE 2 5 STEP 3: FIGURE 3 • SECURELY assemble the LEFT (2) and RIGHT (3) LEG EXT. HANDLES to the BENCH FRAME (7) using two 3/8 X 3-1/4” BOLTS (35), four 3/8” WASHERS (41), and two 3/8” LOCK NUTS (44). See FIGURE 2. • Slide two HINGE TABS (45) onto the BENCH FRAME (7) as shown in FIGURE 2. 3 • SECURELY assemble one 1/8 X 2 X 8? ...
-
Life Fitness 909101 ST - page 6
STEP 4: FIGURE 4 6 STEP 5: FIGURE 5 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble SEAT PAD (15) to HINGE TABS (45) using two 3/8 X 1” BOLTS (38) and two 3/8” WASHERS (41). See FIGURE 4. • SECURELY assemble one 1/2” SPRING PIN (46) to the BENCH FRAME (7) as shown in FIGURE 4. • Assemble RIGHT (12) & LEFT (13) PAD SUPPORTS ...
-
Life Fitness 909101 ST - page 7
FIGURE 6 7 STEP 6: FIGURE 7 • SECURELY assemble BACK PAD (14) to the RIGHT & LEFT PAD SUPPORTS (12) (13) using four 3/8 X 2-3/4” BOLTS (36) and four 3/8” WASHERS (41) as shown in FIGURE 6. • Aseemble two ROLLER PADS (4) to the BENCH FRAME (7) using one 18-1/4” SHAFT (18), four PLASTIC WASHERS (24), and two STARLOCK COLLARS (49) as sho ...
-
Life Fitness 909101 ST - page 8
STEP 9: 8 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble two 3/8” SPRING PINS (47) to the PAD SLEEVES (6) as shown in FIGURE 9. • Assemble four ROLLER PADS (4) to the PAD SLEEVES (6) using four PLASTIC WASHERS (24) and four STARLOCK COLLARS (49). • Slide PAD SLEEVES (6) over LEG PEDESTAL (9) until the spring pin pops into the hole ...
-
Life Fitness 909101 ST - page 9
FIGURE 11 9 • Insert the two GUIDE RODS (5) into the base of the TOWER (1) as shown in FIGURE 11. Lubricate the GUIDE RODS with a slicon or teflon spray that is available at most hardware stores. • Slide two WEIGHT STACK CUSHIONS (26) down over the GUIDE RODS (5). See FIGURE 11. • Using EXTREME CARE slide twenty WEIGHT PLATES (54) down over t ...
-
Life Fitness 909101 ST - page 10
FIGURE 12 10 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 13 STEP 12: • SECURELY assemble two 3-1/2” PULLEYS (22) to the TOWER BRACE (10) using two 3/ 8 X 2” BOLTS (37), and two 3/8” LOCK NUTS (44). See FIGURE 12. • Place TOWER BRACE (10) over the GUIDE RODS (5) and SECURELY fas- ten TOWER BRACE (10) to TOWER (1) using two 1/2 X 4” BOLTS ...
-
Life Fitness 909101 ST - page 11
FIGURE 14 11 STEP 14: • SECURELY assemble the CABLE (23) to the cam on the LEG PEDESTAL (9) using one 3/8 X 1” BOLT (38), one 3/8” WASHER (41), and one 3/8” LOCK NUT (44). See FIGURE 14. • Attach two 1 X 1” GLIDES (29) to the LEFT & RIGHT PAD SUPPORTS (12) (13) approximately where shown in FIGURE 14. • Insert threaded end of CABLE ...
-
Life Fitness 909101 ST - page 12
FIGURE 15 12 STEP 15: • SECURELY assemble three 4-1/2” PULLEYS (21) to the brackets on the BENCH FRAME (7) and LOWER CROSS SUPPORT (8), using three 3/8 X 2” BOLTS (37), one 2-7/8” L-BRACKET (27), and three 3/8” LOCK NUTS (44) as shown in FIGURE 15. 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 23 • Make sure the CABLE (23) is routed around all p ...
-
Life Fitness 909101 ST - page 13
FIGURE 16 13 STEP 16: • Screw the treaded end of the CABLE (23) approximately 3/4” into the end of the WEIGHT STACK SHAFT (19) and tighten jam nut securely. See FIGURE 16. • If the HEAD PLATE (20) does not sit on top of the first WEIGHT PLATE (54), push the head plate down, insert the SELEC- TOR PIN (48) and perform several repetitions on the ...
-
Life Fitness 909101 ST - page 14
FIGURE 17 14 STEP 17: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Loosen the two 1/2 X 3” BOLTS (34) holding the UPPER CROSS SUPORT (11) to the TOWER (1) as shown in FIGURE 17. 16 STEP 18: • Assemble FRONT SHROUD (16) over the pro- truding bolts, then assemble the REAR SHROUD (17) inside of the FRONT SHROUD (16). (NOTE: Make sure shrouds are under ...
-
Life Fitness 909101 ST - page 15
FIGURE 19 15 STEP 19: • Securely tigten the bolts holding the FRONT (16) & REAR (17) SHROUDS. THIS CONCLUDES THE ASSEMBLY OF THE 909101 LEG CURL/EXTENSION TIGHTEN ! TIGHTEN ! ...
Life Fitness 909101 STについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもLife Fitness 909101 STの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがLife Fitness 909101 STで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。