Crimestopper Security Products CS-2002DCの取扱説明書

20ページ 0.41 mb
ダウンロード

ページに移動 of 20

Summary
  • Crimestopper Security Products CS-2002DC - page 1

    CS-2002DC Series IV REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an “On-Guard” Remote Al arm System by Crimestopper Security Products Inc. This booklet contains the information nec essary for installing, using, and maintaining your alarm system. If any questions arise, cont ...

  • Crimestopper Security Products CS-2002DC - page 2

    TABLE OF CONTENTS Installation Cautions & Warnings…….……………………………….……………………………………………2 Control Module & Component M ounting……………...……………………..……………………….…………..3 Wiring……..………………………………………………… ...

  • Crimestopper Security Products CS-2002DC - page 3

    CONTROL MODULE & COMPONENT MOUNTING DO NOT Mount the control unit in the engine comp artment or where the control unit or wiring harness where they can become entangled with moving par ts such as brake/gas/clutch pedals, or the steering column! The alarm control module s hould be mounted in a concealed location. The Placement of the module will ...

  • Crimestopper Security Products CS-2002DC - page 4

    WIRING BLACK WIRE: SYSTEM CHASSIS GROUND The Black wire MUST be connected t he CHASSIS METAL of the vehicle. Scrape away any paint or debris from the connection point and use a star washer to ensure a good connection. Keep the ground wire short. YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS Connect to an IGNITION wire (or fuse i ...

  • Crimestopper Security Products CS-2002DC - page 5

    WIRING BLUE/WHITE WIRE: (-) PASSENGER(S) DOOR UNL OCK OUTPUT (Optional, requires relay ) Connects to unlock circuit for passenger door(s) when using separate driver’s door unlock option. See SEPARATE DRIVER’S DOOR UNLOCK WIRING on Page 8 for some configuration options. BROWN WIRE: (+) SIREN OUTPUT (3 Amp Max.) Connect to RED siren wire from the ...

  • Crimestopper Security Products CS-2002DC - page 6

    WIRING RED WIRE: +12V POWER INPUT (15 amp fuse) Connect to +12 Volt source with supplied fuse & holder. Recommended location for this connection is at the vehicle battery positive terminal. 14 GA. BROWN WIRE: (On-board Starter Disable Relay) Cut the 14GA. Brown wire in half. Connect the 2 female terminals to the Male terminals on the control mo ...

  • Crimestopper Security Products CS-2002DC - page 7

    NEGA TIVE TRIGGER DOORLOCK WIRING POS ITIVE TRIG GER DOO RLOCK WIRIN G GREEN GREEN FU SED RED +12V RED BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FAC TO RY FAC TO RY L L POWER POWER LOCKING LOCKING UL UL RELA YS RELA YS REVE RSE P OLARITY DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED +12V +12V BLUE BLUE + + 86 85 86 85 86 85 86 85 87 87 87 87 3 ...

  • Crimestopper Security Products CS-2002DC - page 8

    SEPARATE DRIVER’S DOOR UNLOCK WIRING NEGA TIVE T RIGGER DOOR LOCKS BLUE/W HIT E GREEN RED BLUE DRIVER'S DOOR MOTOR 86 85 L L 87 UL UL 87A 30 F ACTOR Y LOCK RELA YS +12V + FUSED UNLOCK W IRE CUT WIRING FOR REVERSE POLA RITY DOOR LOCKS BLUE/W HITE GREEN FU SED RED +12V BLUE + MASTER 86 85 86 85 SW ITC H 86 85 87 87 87 30 87A 30 87A 30 87A + L ...

  • Crimestopper Security Products CS-2002DC - page 9

    TRANSMITTER PROGRAMMING NOTE: All transmitters must be learned at the time of programming. This system can learn up to 4 remotes. 1. Turn key to the ON position and press program button 4 times. 2. After a short delay, the unit will flash the parking lights 4 times. 3. Press the Button #1 (Lock) on the remote you wish to program. 4. You should get ...

  • Crimestopper Security Products CS-2002DC - page 10

    OPTION PROGRAMMING 1. Turn the Ignition ON and press the Override/Program button 5 times. 2. After a short delay, the parking lights will flash 5 times and status LED will be on solid. 3. Within the next few seconds, press the Override/ Program button [again] the number of times that corresponds to the options chart below. Parking lights and/or opt ...

  • Crimestopper Security Products CS-2002DC - page 11

    OPTION PROGRAMMING 1. HORN CHIRPS / PULSES This option controls the system’s Factory Vehicle H orn output. There are 3 selections: Button 1 (Lock) = Horn Pulse only when alarm is tripped. Button 2 (Unlock) = Horn Chirps for Arm / Disarm and Pulse when tripped. Button 3 (Trunk) = Horn Chirps for Arm, Disarm, and Pre-warning protection. All setting ...

  • Crimestopper Security Products CS-2002DC - page 12

    OPTION PROGRAMMING 7. DOUBLE UNLOCK PULSE With this feature enabled, the unit will send 2 unlock pul ses when the #2 Unlock button is pressed. 2 pulses are required for interfacing into some existing Factory Keyless Entry or Alarm systems on vehicles such as Nissan, VW, Toyota, and Lexus vehicles. 8. SILENT ARMING /DISARMING (CHIRP DEFEAT) With thi ...

  • Crimestopper Security Products CS-2002DC - page 13

    PROGRAMMABLE OPTION RESET Follow the steps below to reset ALL OPTION VAL UES ON PAGE 10 TO FACTORY DEFAULT SETTINGS. 1. Turn the Ignition ON and press the Override/Program button 5 times. You should hear a long chirp. 2. Immediately press Button #3 (Trunk) on the remote. 3. The siren will chirp 4 times and lights will flash 4 times. 4. Turn off ign ...

  • Crimestopper Security Products CS-2002DC - page 14

    OPERATING INSTRUCTIONS 6 BUTTON REMOTE TRANSMITTER: #3 #1 #2 #4 LOCK TR U N K PA N I C UNLOCK BA N K #2 FLA SH LIGHT (A U X.) PAN I C BANK #1 (Directly Press Buttons) Button 1: Arm Button 2: Disarm Button 3: Aux #1 (Trunk) Button 4: Panic Button 5: (Change to BANK #2) BANK #2* (Press Bank #2 button FIRST, then within 3 seconds Buttons 1-4) Button 1 ...

  • Crimestopper Security Products CS-2002DC - page 15

    OPERATING INSTRUCTIONS TRUNK/HATCH POP (REMOTE AUX. OUTPUT 1, OPTIONAL) To pop the trunk (if optional feature is installed), press Button #3 (Trunk Symbol) on the transmitter for at least 1½ seconds. If the system is armed, pressing Button #3 may or may not trip the alarm system when opening the trunk depending on programming option (10). See page ...

  • Crimestopper Security Products CS-2002DC - page 16

    OPERATING INSTRUCTIONS VALET MODE To disable the Alarm system for vehicle serv ice or otherwise, turn the ignition on and press the override/program button 4-5 seconds until the dash LED t urns on solid and you hear (1) siren chirp. Repeat the process to exit VALET mode and the system will ch irp (2) times and the LED will turn off. Lock/Unlock and ...

  • Crimestopper Security Products CS-2002DC - page 17

    OPERATING INSTRUCTIONS ACTIVE RE-ARMING (FAIL-SAFE PROTECTION) Active Re-arming means that the system will re-arm itself 30 seconds after disarmed with the transmitter if a door has not yet been opened. This is handy if the vehicle is accidenta lly disarmed (via the transmi tter in your pocket) without you knowing it. This feature can also be turne ...

  • Crimestopper Security Products CS-2002DC - page 18

    CARJACK PROTECTION FEATURES FULL-TIME CARJACK ONLY USE THIS MODE WHEN THERE IS AN EXTREME TREAT OF A CARJACK WITH YOUR VEHICLE. Full-time Carjack protection must be enabled before use through Alarm programming options (13) & (14). See page 10. EVERY TIME the Ignition is turned ON or a door is opened and closed with the Ignition ON, a Carjack co ...

  • Crimestopper Security Products CS-2002DC - page 19

    + - + BLACK(GROUND ) W H ITE( W ARN ING) RED (+) BLUE (TRIGGER) RED WHIT E BROWN BLUE/WHITE WHIT E/R ED ORANGE BLACK/WHITE BLUE GRA Y YELLOW BLACK VIOLET GREEN LED OVERRIDE/ PROGRA M BUTTO N BA TTERY (-) LOCK OUTPUT +12 VOL T FOR RELA YS (-) UNLOCK OUTPUT GREEN BLUE RED (-) NEG . DOO R PIN SWITCH (+) POSITIVE DOOR PIN SW ITCH FUSE BOX IGN. SW (-) R ...

  • Crimestopper Security Products CS-2002DC - page 20

    ONLINE TECHNICAL SUPPORT www.crimestopper.com/techweb03.html www.crimestopper.com email@crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2003 Crimestopper Security Products ...

メーカー Crimestopper Security Products カテゴリー Home Security System

Crimestopper Security Products CS-2002DCのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CS-2002DCの取扱説明書
- Crimestopper Security Productsの製品カード
- パンフレット
- またはCrimestopper Security Products CS-2002DCの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Crimestopper Security Products CS-2002DCの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Crimestopper Security Products CS-2002DCの取り付け説明書、サービスマニュアル、簡易説明書、またはCrimestopper Security Products CS-2002DCのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Crimestopper Security Products CS-2002DCの製品を使用するにあたって最も人気のある説明書を閲覧できます。

Crimestopper Security Products CS-2002DCデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCrimestopper Security Products CS-2002DCを使用するのを助ける技術的文書のことです。説明書は通常、全てのCrimestopper Security Products CS-2002DCユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Crimestopper Security Productsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Crimestopper Security Products CS-2002DCの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCrimestopper Security Products CS-2002DCの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Crimestopper Security Products CS-2002DCに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Crimestopper Security Products CS-2002DCデバイスの基本機能を使うにあたってのヒント。 Crimestopper Security Products CS-2002DCのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Crimestopper Security Products CS-2002DCに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCrimestopper Security Products CS-2002DCのメーカー/サービスへの連絡先に関する情報。

Crimestopper Security Products CS-2002DCについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCrimestopper Security Products CS-2002DCの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCrimestopper Security Products CS-2002DCで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)