English dropdown-ico

Manual Crimestopper Security Products CS-2002DC

20 pages 0.41 mb
Download

Go to site of 20

Summary
  • Crimestopper Security Products CS-2002DC - page 1

    CS-2002DC Series IV REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an “On-Guard” Remote Al arm System by Crimestopper Security Products Inc. This booklet contains the information nec essary for installing, using, and maintaining your alarm system. If any questions arise, cont ...

  • Crimestopper Security Products CS-2002DC - page 2

    TABLE OF CONTENTS Installation Cautions & Warnings…….……………………………….……………………………………………2 Control Module & Component M ounting……………...……………………..……………………….…………..3 Wiring……..………………………………………………… ...

  • Crimestopper Security Products CS-2002DC - page 3

    CONTROL MODULE & COMPONENT MOUNTING DO NOT Mount the control unit in the engine comp artment or where the control unit or wiring harness where they can become entangled with moving par ts such as brake/gas/clutch pedals, or the steering column! The alarm control module s hould be mounted in a concealed location. The Placement of the module will ...

  • Crimestopper Security Products CS-2002DC - page 4

    WIRING BLACK WIRE: SYSTEM CHASSIS GROUND The Black wire MUST be connected t he CHASSIS METAL of the vehicle. Scrape away any paint or debris from the connection point and use a star washer to ensure a good connection. Keep the ground wire short. YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS Connect to an IGNITION wire (or fuse i ...

  • Crimestopper Security Products CS-2002DC - page 5

    WIRING BLUE/WHITE WIRE: (-) PASSENGER(S) DOOR UNL OCK OUTPUT (Optional, requires relay ) Connects to unlock circuit for passenger door(s) when using separate driver’s door unlock option. See SEPARATE DRIVER’S DOOR UNLOCK WIRING on Page 8 for some configuration options. BROWN WIRE: (+) SIREN OUTPUT (3 Amp Max.) Connect to RED siren wire from the ...

  • Crimestopper Security Products CS-2002DC - page 6

    WIRING RED WIRE: +12V POWER INPUT (15 amp fuse) Connect to +12 Volt source with supplied fuse & holder. Recommended location for this connection is at the vehicle battery positive terminal. 14 GA. BROWN WIRE: (On-board Starter Disable Relay) Cut the 14GA. Brown wire in half. Connect the 2 female terminals to the Male terminals on the control mo ...

  • Crimestopper Security Products CS-2002DC - page 7

    NEGA TIVE TRIGGER DOORLOCK WIRING POS ITIVE TRIG GER DOO RLOCK WIRIN G GREEN GREEN FU SED RED +12V RED BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FAC TO RY FAC TO RY L L POWER POWER LOCKING LOCKING UL UL RELA YS RELA YS REVE RSE P OLARITY DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED +12V +12V BLUE BLUE + + 86 85 86 85 86 85 86 85 87 87 87 87 3 ...

  • Crimestopper Security Products CS-2002DC - page 8

    SEPARATE DRIVER’S DOOR UNLOCK WIRING NEGA TIVE T RIGGER DOOR LOCKS BLUE/W HIT E GREEN RED BLUE DRIVER'S DOOR MOTOR 86 85 L L 87 UL UL 87A 30 F ACTOR Y LOCK RELA YS +12V + FUSED UNLOCK W IRE CUT WIRING FOR REVERSE POLA RITY DOOR LOCKS BLUE/W HITE GREEN FU SED RED +12V BLUE + MASTER 86 85 86 85 SW ITC H 86 85 87 87 87 30 87A 30 87A 30 87A + L ...

  • Crimestopper Security Products CS-2002DC - page 9

    TRANSMITTER PROGRAMMING NOTE: All transmitters must be learned at the time of programming. This system can learn up to 4 remotes. 1. Turn key to the ON position and press program button 4 times. 2. After a short delay, the unit will flash the parking lights 4 times. 3. Press the Button #1 (Lock) on the remote you wish to program. 4. You should get ...

  • Crimestopper Security Products CS-2002DC - page 10

    OPTION PROGRAMMING 1. Turn the Ignition ON and press the Override/Program button 5 times. 2. After a short delay, the parking lights will flash 5 times and status LED will be on solid. 3. Within the next few seconds, press the Override/ Program button [again] the number of times that corresponds to the options chart below. Parking lights and/or opt ...

  • Crimestopper Security Products CS-2002DC - page 11

    OPTION PROGRAMMING 1. HORN CHIRPS / PULSES This option controls the system’s Factory Vehicle H orn output. There are 3 selections: Button 1 (Lock) = Horn Pulse only when alarm is tripped. Button 2 (Unlock) = Horn Chirps for Arm / Disarm and Pulse when tripped. Button 3 (Trunk) = Horn Chirps for Arm, Disarm, and Pre-warning protection. All setting ...

  • Crimestopper Security Products CS-2002DC - page 12

    OPTION PROGRAMMING 7. DOUBLE UNLOCK PULSE With this feature enabled, the unit will send 2 unlock pul ses when the #2 Unlock button is pressed. 2 pulses are required for interfacing into some existing Factory Keyless Entry or Alarm systems on vehicles such as Nissan, VW, Toyota, and Lexus vehicles. 8. SILENT ARMING /DISARMING (CHIRP DEFEAT) With thi ...

  • Crimestopper Security Products CS-2002DC - page 13

    PROGRAMMABLE OPTION RESET Follow the steps below to reset ALL OPTION VAL UES ON PAGE 10 TO FACTORY DEFAULT SETTINGS. 1. Turn the Ignition ON and press the Override/Program button 5 times. You should hear a long chirp. 2. Immediately press Button #3 (Trunk) on the remote. 3. The siren will chirp 4 times and lights will flash 4 times. 4. Turn off ign ...

  • Crimestopper Security Products CS-2002DC - page 14

    OPERATING INSTRUCTIONS 6 BUTTON REMOTE TRANSMITTER: #3 #1 #2 #4 LOCK TR U N K PA N I C UNLOCK BA N K #2 FLA SH LIGHT (A U X.) PAN I C BANK #1 (Directly Press Buttons) Button 1: Arm Button 2: Disarm Button 3: Aux #1 (Trunk) Button 4: Panic Button 5: (Change to BANK #2) BANK #2* (Press Bank #2 button FIRST, then within 3 seconds Buttons 1-4) Button 1 ...

  • Crimestopper Security Products CS-2002DC - page 15

    OPERATING INSTRUCTIONS TRUNK/HATCH POP (REMOTE AUX. OUTPUT 1, OPTIONAL) To pop the trunk (if optional feature is installed), press Button #3 (Trunk Symbol) on the transmitter for at least 1½ seconds. If the system is armed, pressing Button #3 may or may not trip the alarm system when opening the trunk depending on programming option (10). See page ...

  • Crimestopper Security Products CS-2002DC - page 16

    OPERATING INSTRUCTIONS VALET MODE To disable the Alarm system for vehicle serv ice or otherwise, turn the ignition on and press the override/program button 4-5 seconds until the dash LED t urns on solid and you hear (1) siren chirp. Repeat the process to exit VALET mode and the system will ch irp (2) times and the LED will turn off. Lock/Unlock and ...

  • Crimestopper Security Products CS-2002DC - page 17

    OPERATING INSTRUCTIONS ACTIVE RE-ARMING (FAIL-SAFE PROTECTION) Active Re-arming means that the system will re-arm itself 30 seconds after disarmed with the transmitter if a door has not yet been opened. This is handy if the vehicle is accidenta lly disarmed (via the transmi tter in your pocket) without you knowing it. This feature can also be turne ...

  • Crimestopper Security Products CS-2002DC - page 18

    CARJACK PROTECTION FEATURES FULL-TIME CARJACK ONLY USE THIS MODE WHEN THERE IS AN EXTREME TREAT OF A CARJACK WITH YOUR VEHICLE. Full-time Carjack protection must be enabled before use through Alarm programming options (13) & (14). See page 10. EVERY TIME the Ignition is turned ON or a door is opened and closed with the Ignition ON, a Carjack co ...

  • Crimestopper Security Products CS-2002DC - page 19

    + - + BLACK(GROUND ) W H ITE( W ARN ING) RED (+) BLUE (TRIGGER) RED WHIT E BROWN BLUE/WHITE WHIT E/R ED ORANGE BLACK/WHITE BLUE GRA Y YELLOW BLACK VIOLET GREEN LED OVERRIDE/ PROGRA M BUTTO N BA TTERY (-) LOCK OUTPUT +12 VOL T FOR RELA YS (-) UNLOCK OUTPUT GREEN BLUE RED (-) NEG . DOO R PIN SWITCH (+) POSITIVE DOOR PIN SW ITCH FUSE BOX IGN. SW (-) R ...

  • Crimestopper Security Products CS-2002DC - page 20

    ONLINE TECHNICAL SUPPORT www.crimestopper.com/techweb03.html www.crimestopper.com email@crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2003 Crimestopper Security Products ...

Manufacturer Crimestopper Security Products Category Home Security System

Documents that we receive from a manufacturer of a Crimestopper Security Products CS-2002DC can be divided into several groups. They are, among others:
- Crimestopper Security Products technical drawings
- CS-2002DC manuals
- Crimestopper Security Products product data sheets
- information booklets
- or energy labels Crimestopper Security Products CS-2002DC
All of them are important, but the most important information from the point of view of use of the device are in the user manual Crimestopper Security Products CS-2002DC.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Crimestopper Security Products CS-2002DC, service manual, brief instructions and user manuals Crimestopper Security Products CS-2002DC. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Crimestopper Security Products CS-2002DC.

Similar manuals

A complete manual for the device Crimestopper Security Products CS-2002DC, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Crimestopper Security Products CS-2002DC by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Crimestopper Security Products CS-2002DC.

A complete Crimestopper Security Products manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Crimestopper Security Products CS-2002DC - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Crimestopper Security Products CS-2002DC, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Crimestopper Security Products CS-2002DC, that we can find in the current document
3. Tips how to use the basic functions of the device Crimestopper Security Products CS-2002DC - which should help us in our first steps of using Crimestopper Security Products CS-2002DC
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Crimestopper Security Products CS-2002DC
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Crimestopper Security Products CS-2002DC in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Crimestopper Security Products CS-2002DC?

Use the form below

If you did not solve your problem by using a manual Crimestopper Security Products CS-2002DC, ask a question using the form below. If a user had a similar problem with Crimestopper Security Products CS-2002DC it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)