-
Chicago Electric 93853 - page 1
DEMOLITION HAMMER Model 93853 SET UP AND OPERA TING INSTRUCTIONS Visit our website at: http://www .harborfreight.com Read this material before using this product. Failure to do so can result in serious injury . SA VE THIS MANUAL. Copyright © 2006 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork contained ...
-
Chicago Electric 93853 - page 2
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 2 SPECIFICA TIONS Electrical Requirements 120 V~ / 60 Hz / 1500 W 20 A (Start Up) / 9.5 A (No Load) / 13.0 A (With Load) Power Cord T ype: 82” Long / 14 A WG x 2C Power Cord Plug T ype: 2-Prong / Polarized Power Switch T ype: 2-Position T oggle Switch w/Slider Cover Blows Per Min ...
-
Chicago Electric 93853 - page 3
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 3 ELECTRICAL SAFETY Grounded tools must be plugged into an outlet properly installed and 1. grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way . Do not use any adapter plugs. Check with a qualied electrician if yo ...
-
Chicago Electric 93853 - page 4
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 4 Remove adjusting keys or wrenches before turning the power tool on. 4. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury . Do not overreach. Keep proper footing and balance at all times. 5. Proper footing and balance enable ...
-
Chicago Electric 93853 - page 5
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 5 SER VICE T ool service must be performed only by qualied repair personnel. 1. Service or maintenance performed by unqualied personnel could result in a risk of injury . When servicing a tool, use only identical replacement parts. Follow 2. instructions in the “Inspection, ...
-
Chicago Electric 93853 - page 6
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 6 Do not drill or break into existing walls, oors, or other blind areas where 1 1. electrical wiring may exist. If this situation is unavoidable, disconnect all fuses or circuit breakers feeding the worksite. Use a metal detector to determine if there are gas or water pipes hidd ...
-
Chicago Electric 93853 - page 7
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 7 these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement or other masonry products, arsenic and chromium from chemically treated lumber . Y our risk from these exposures varies, depending on how often you do this type of work. T o reduce your ex ...
-
Chicago Electric 93853 - page 8
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 8 VIBRA TION HAZARD This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury , particularly to the hands, arms and shoulders. T o reduce the risk of vibration-related injury: Anyone using vibrating tools regularly o ...
-
Chicago Electric 93853 - page 9
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 9 GROUNDING Improperly connecting the grounding wire can result in electric shock. Check with a qualied electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from ...
-
Chicago Electric 93853 - page 10
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 10 with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Outlets for 2-Prong Plug.) Double insulated tools may be used in either of the 120 volt outlets shown in the 2. preceding illustration. (Se ...
-
Chicago Electric 93853 - page 11
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 1 1 RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120/240 VOL T) NAMEPLA TE AMPERES (at full load) EXTENSION CORD LENGTH 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 ? ...
-
Chicago Electric 93853 - page 12
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 12 UNP ACKING When unpacking, check to make sure all the parts shown on the Parts List on page 16 are included. If any parts are missing or broken, please call Harbor Freight T ools at the number shown on the cover of this manual as soon as possible. PRODUCT FEA TURES Note: For add ...
-
Chicago Electric 93853 - page 13
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 13 V ariable Speed Control (72): 3. The Demolition Hammer is equipped with a V ariable Speed Control Dial. The impact rate (BPM) and rotating speed (RPM) can be varied according to the type of work being performed by setting the V ariable Speed Control Dial to the selected setting: ...
-
Chicago Electric 93853 - page 14
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 14 Grasp the Demolition Hammer rmly by its rear Handle (62) and Auxiliary Handle 3. (104A). Then, turn the Power Switch (66) to its “ON” position to begin work. IMPORT ANT : 4. This Demolition Hammer requires a short period of time to warm up. Depending on the room temperatu ...
-
Chicago Electric 93853 - page 15
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 15 are worn down, replace both Carbon Brushes. If, however , the Carbon Brushes are just dirty they may be cleaned by rubbing them with a pencil eraser . If cleaning and replacing used brushes, try to install them in the same holders and in the same direction they were removed. Whe ...
-
Chicago Electric 93853 - page 16
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 16 TROUBLESHOOTING Problem Possible Solution Chisel installs with difculty . Make sure the Chisel shank, Front Cap, and Slider are free of debris and lightly oiled or greased. (See page 12.) T ool does not run. Make sure the Power Switch is in its “ON” position. (See page 1 ...
-
Chicago Electric 93853 - page 17
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 17 P ARTS LIST REV 06f, 08g, 10d * Cannot be ordered individually . Must be ordered as a complete Motor Assembly . Includes parts 33, 34, 35, 36, 37, 40, 58, 59, 60, 61, 73, 74. ** Cannot be ordered individually . Must be ordered as a complete Carbon Brush Assembly . Includes parts ...
-
Chicago Electric 93853 - page 18
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 18 ASSEMBL Y DIAGRAM REV 08g, 10d Note: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. 106: Spade Chisel not shown. 107: Ball Point Chisel not shown. ...
-
Chicago Electric 93853 - page 19
SKU 93853 For technical questions, please call 1-800-444-3353 P AGE 19 LIMITED 1 YEAR / 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor , the belts ...
Chicago Electric 93853についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもChicago Electric 93853の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがChicago Electric 93853で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。