Bay Technical Associates 400-ST1の取扱説明書

40ページ 0.54 mb
ダウンロード

ページに移動 of 40

Summary
  • Bay Technical Associates 400-ST1 - page 1

    Part No. 304433-A Rev 00 November 1998 Installing the Ba yStac k 400 -ST1 Cascade Module ...

  • Bay Technical Associates 400-ST1 - page 2

    © 1998 by Bay Networks, Inc. All rights res e rved. T rad emarks Bay Networks i s a registered tr ademark and BayStack is a t rademark of Bay Networks, Inc. All other trademarks and registered t rademark s are property of their respecti ve o wners. Statem en t of Con di tio ns In the interest of impr oving internal design, ope ration al function, ...

  • Bay Technical Associates 400-ST1 - page 3

    1 Intr oduction This guide pro vides procedures for installing the BayStack 400-ST1 Cascade Modules into suppo rted Bay Networ ks BayStack 450 switches that ar e configured with B ayStack 450 software version V1.1.0 or later . Y ou can determine the software v ersion of your switches b y accessing the System Characteristics screen for each switch. ...

  • Bay Technical Associates 400-ST1 - page 4

    2 Find t he Bay Networks prod uct for which you need documentation. Then locate the specific cate gory and model o r versio n for your har dware or soft ware product . Using Adobe Acrobat R eader , you can open the man uals and release notes, sear ch for the sections you need, and print t hem on most st andard printer s. Y ou can do wnload Acrobat ...

  • Bay Technical Associates 400-ST1 - page 5

    3 Contents of Shipment Each BayStack 400-ST1 shipm ent includes the following items ( Figur e 1 ): • One BayStack 400 -ST1 Cascade Module • One .30 meter (1 2 inch) cascade cable; part numb er 303978- A. • This guide ( Installing the BaySta c k 400-ST1 C as c ade Module ). Figure 1. Contents of Shipment For stacking three or more units (maxim ...

  • Bay Technical Associates 400-ST1 - page 6

    4 If an y items are missing or damaged, contact the sales agent or the cu stomer service representati ve from wh om you purchased the BayStack 400-ST1 cascade module. Y ou will need a Phillips scre wdriver for the install ation. Ba y Stac k 40 0-ST1 Front Panel Components The front-p anel components of the BayStack 400 -ST1 Cascade Module are sho w ...

  • Bay Technical Associates 400-ST1 - page 7

    5 Cascade A Out Connector Provides an attachmen t point for connecting this unit t o another unit via the cascade cable. A re t u r n cable fro m another unit’ s Cascade A Out conn ector to this unit’ s Cascade A In connector c ompletes the stack connection (see the ex ample shown in Figu re 3 ). Unit Select Sw itch The Unit Select switch (up = ...

  • Bay Technical Associates 400-ST1 - page 8

    6 Cascade A I n Connector Provides an attachment point for accepting a cascade cable connection from an adjacent unit in the stack. A re t u r n cable from this unit’ s Cascade A Out connecto r to the adjacent unit’ s Casca de A In connector completes the stack connection (see the e xample shown in Figure 3 ). Figure 3. Connecting Casca de Cabl ...

  • Bay Technical Associates 400-ST1 - page 9

    7 Base Unit Descr iption The base unit is a unique stack un it that can be selected by the Unit Select switch o n the front -panel of the 400-ST1 cascade module. One unit in th e stack configuration must be assigned as the bas e unit; all other units in the stack must have t heir Unit Select switch set to Off (see “ Un it Select Switch ” on pag ...

  • Bay Technical Associates 400-ST1 - page 10

    8 • Stack IP MA C address --- The s tac k IP MAC add r ess is automatically assigned during the stack in itialization: The base unit’ s MA C address, with a softwar e offset, is used for the stack IP MA C address. For e xample, if the base unit’ s MA C address is: 00-00-8 2-99-44-00 and the Stack s oftware of fset is: 1F then the Stack IP MA ...

  • Bay Technical Associates 400-ST1 - page 11

    9 • T emporary Base Unit --- If an assigned base unit fails, the next unit in the stack order automatically becom es the new temp or ary b ase unit . This change is ind icated by the Base LED on the temporary base unit’ s LED displa y panel turn ing on (ye llow). The automatic base unit chan ge to the ne x t un it in the stack order is a temp o ...

  • Bay Technical Associates 400-ST1 - page 12

    10 Stack Configurations As sho w n in Figur e 4 , the cascade connectors and cables on the 400-ST1 front-panel provide the ability to stack up to eight BayStack switches. W ith 400-4TX MD As installed in each switch, the stack can accom modate a maximum of 224 switch p orts. Because stack par ameters are associated with th e base unit (see “ Bas ...

  • Bay Technical Associates 400-ST1 - page 13

    11 Figure 4. Stack Up Configuratio n Example Unit 7 Unit 8 1 = Last unit 2 = Base unit 3 = Cascade cable (PN 303978-A) 4 = Cascade max-return cable (PN 303979-A) BS0033A Unit 5 Unit 6 Unit 3 Unit 4 Unit 1 Unit 2 2 1 3 O u t I n 4 ...

  • Bay Technical Associates 400-ST1 - page 14

    12 Figure 5. Stack Do wn Configuration Examp le Unit 2 1 = Base unit 2 = Last unit 3 = Cascade cable (PN 303978-A) 4 = Cascade max-return cable (PN 303979-A) BS0034A Unit 1 Unit 4 Unit 3 Unit 6 Unit 5 Unit 8 Unit 7 2 1 I n O u t 4 3 ...

  • Bay Technical Associates 400-ST1 - page 15

    13 Certain n etwork m anagement station (NMS) applicatio ns assume a stack do wn configura tion for the graphical user interface (GUI) that represents the stack (see Figur e 5 on page 12 ). F or this reason, Bay Netwo rks recom mends that you alw ays configu re the top unit in the stack as the base unit. In any stack configuration, the follo win g ...

  • Bay Technical Associates 400-ST1 - page 16

    14 Redundant Cascade Stacking Feature BayStack 400-ST1 Cascade Modules allo w you to connect up to 8 units into a red undant cascade stack. If any single unit fails or if a cable is accidently disconnected, other units in the stack remain o perational, without int erruption. Figur e 6 shows an e xample of ho w a stack conf iguration reacts to a fai ...

  • Bay Technical Associates 400-ST1 - page 17

    15 Figure 6. Redundant Cascade St acki ng Feature Unit 2 1 = Base unit 2 = Last unit 3 = Cascade cable (PN 303978-A) 4 = Cascade max-return cable (PN 303979-A) BS0035A Cascade A Out Cascade A In Unit 1 Unit 5 Unit 4 Unit 3 2 1 B A 4 3 ...

  • Bay Technical Associates 400-ST1 - page 18

    16 Installation This secti on describes ho w to connect u p to eight BayStack 1 0/100/1000 Seri es switches into a red undant stack. The switch stack can consist of an y combination of BayStack 4 50-24T and Ba yStack 450-12T switch models. Before installing y our equipment, revie w the previous sections of this guide. This section inclu d es the fo ...

  • Bay Technical Associates 400-ST1 - page 19

    17 Installing the 400 -ST1 Cascade Module The Cascade Module slot on the BayStack 450 switch can accommodate a single 4 00-ST1 Cascade Module. T o install a 400-ST1 Cascade Module into the Cascade Module slot, follo w these steps: 1. Unplug the A C power cord fr om the back of the switch. 2. Loosen the thumbscrews and r emove the f iller panel from ...

  • Bay Technical Associates 400-ST1 - page 20

    18 Figure 8. Installing a 400-ST1 Cascad e Module 4. Pr ess the m odule firmly into th e chas sis slot. B e sure that the module is fully seated into the mating connector . 5. Secure the module in the chass is by tightening the thu mb scr ews on t he modu le fr ont panel. 6. Repeat St ep s 1 to 5 f or each switch that is to be conf igur ed with the ...

  • Bay Technical Associates 400-ST1 - page 21

    19 Installing and Connecting Multiple Switches The procedure to install an d connect multip le switches is similar for tabletop, shelf, or stand ard 19-in ch utility rack installation s. T o install multiple swit ches, follow these steps: 1. Install one unit at a time in the rack or on the sh elf or ta ble top . Refer to the Usi ng the BayStac k 45 ...

  • Bay Technical Associates 400-ST1 - page 22

    20 5. Set the Unit Select switch f or the base unit to the Base (up = Ba se) positio n ( Figure 9 ). 6. Set the Unit Select switch f or all other units in the stack to th e Off (down = Off) position Only one unit in the stack can be the base unit. Figure 9. Setting the Unit Select Switch Cascade A Out Cascade A In Unit Select Base BS0038A Off ...

  • Bay Technical Associates 400-ST1 - page 23

    21 7. Connect the units using the supplied cascade cables ( Figu re 10 ). a. Connect one end of a cascade cable to the Cascade A Out connector on th e Base Unit (unit 1). Figure 10. Installing Casc ade Cable s Cascade A Out Unit 2 1 = Base unit 2 = Last unit 3 = Cascade cable (PN 303978-A) 4 = Cascade max-return cable (PN 303979-A) BS0039A Cascade ...

  • Bay Technical Associates 400-ST1 - page 24

    22 b . Connect the other end of the cascad e cable to the cascade A In connector on the unit just below the base unit (un it 2), or just ab ove the base unit if cascading up t he stack. c. Continue attaching the cascade cables until the last unit is configured. A maximum of eig ht units can be conf igured per stack. d. At the last unit in the stack ...

  • Bay Technical Associates 400-ST1 - page 25

    23 Connecting P ower When the stack is init ially po w ered up, the software automaticall y ass igns unit numb ers to the units (t he indi vidual switches in the stack). T he unit numbers correspond to the phys ical stack power up/initialization sequence, beginning wi th the base un it as unit 1. The stack initiali zation sequence takes ap proximat ...

  • Bay Technical Associates 400-ST1 - page 26

    24 One or tw o A C po wer strips may be req uired to accommodate the quantity of switches in the stack. 3. A pply power to the A C power strip. Set the A C power strip On/Of f switch to On (or connect th e AC power s trip to a groun ded A C po wer outlet). 4. Proc ee d to “ V erifying the Installation ” f ollowing this section. V erifying the I ...

  • Bay Technical Associates 400-ST1 - page 27

    25 Figure 11. V erifying the Instal lation • The Base LED f or the base un it only is on. If one (or more) Base LEDs ar e blinking, no unit (or more than on e unit) is configu red as the base unit. If the LEDs o n any of the units in the stack are not as shown in F igure 11 , cycle the power to the stack and v erify the LEDs. Refer to Using th e ...

  • Bay Technical Associates 400-ST1 - page 28

    26 Modifying an Existing Stac k Configuration This section p r ovides e xam ples of how to mo dify an existing stack con figuration. T he examples assume the stack conf igur ation is operation al with connected stations. Alw ays notify the attached stations that there may b e a temporar y disruption o f the netw ork services befo re you begin the m ...

  • Bay Technical Associates 400-ST1 - page 29

    27 Assigning a New Base Unit to the Stack T o assign a new base unit to the s tack, complete the fol lowi ng step s: 1. Set the U nit Select switch on the original base uni t to the Of f position. See Figur e 9 on page 20 for details ab ou t the Unit Select switch. 2. Set the U nit Select switch on the new b ase unit to the Base posi tion. 3. Renum ...

  • Bay Technical Associates 400-ST1 - page 30

    28 Adding Units to the Stac k This sect io n des cri b es ho w to add one or more un it s t o the middle of a stack or to the end of a stack. Adding Un its to the Mid dle of a Stac k T o add one or more units to th e middle of a stack, complete the following steps: 1. Determine the position of the n e w units in the existing stack ( Figu re 12 ). F ...

  • Bay Technical Associates 400-ST1 - page 31

    29 For table top configu rations , te mpor arily move units 1 and 2 to allo w space for units 5 an d 6. Figure 12. Adding to Middle of Sta ck 4. Add t h e ne w un its to t h e desir ed locat i o n. Fo r tabletop conf iguratio ns, replace units 1 an d 2 (tempor arily mov ed in Step 4). 1 = Base unit 2 = Last unit 3 = Cascade cable (PN 303978-A) 4 = ...

  • Bay Technical Associates 400-ST1 - page 32

    30 5. Reconnect the cascade cable from unit 2 to the Cascade A In connector of (new) unit 5. 6. Connect a cascade cable from the C ascade A Out connector of unit 5 to the Cascade A In connector of unit 6 . 7. Connect a cascade cable from the C ascade A Out connector of unit 6 to the Cascade A In connector of unit 3 . 8. Renu mber the order of the u ...

  • Bay Technical Associates 400-ST1 - page 33

    31 Figure 13. Adding to End of Stac k 2. Disconn ect the cascade max-retur n cable (item 4) fro m the Cascade A Out connector at unit 4. Leav e the other end o f the cascade max-return cable connected to the Cascade A In connector at unit 1. 3. Add the new units (units 5 and 6) to the end of th e stack con f igura tion. 1 = Base unit 2 = Last unit ...

  • Bay Technical Associates 400-ST1 - page 34

    32 4. Connect a cascade cable from the C ascade A Out connector of unit 4 to the Cascade A In connector of unit 5 . 5. Connect a cascade cable from the C ascade A Out connector of unit 5 to the Cascade A In connector of unit 6 . 6. Reconnect the cascade max-r eturn cable fr o m unit 1 to the Cascade A Out co n nector of unit 6. 7. Renu mber the ord ...

  • Bay Technical Associates 400-ST1 - page 35

    33 Remo ving/Replacing Ad jacent Units T o remove/rep lace adjacent units from an oper at ing stack, complete the following steps (see Figu re 14 ): 1. Remove the cascade cable from the Cascade A Out connector at unit 2. Figure 14. Remo ving Adjacent Units 1 = Base unit 2 = Last unit BS0043A Unit 2 Unit 1 Unit 4 Unit 3 Unit 6 Unit 5 2 1 Cascade A O ...

  • Bay Technical Associates 400-ST1 - page 36

    34 2. Remove the cascade cable fr om the Cascade A In connector at unit 5. 3. Remove the units (units 3 and 4) and in stall replacement units as r equ ired. 4. Renu mber the ord er of the units fo r the new stack configuration (if desired). Y ou can renumber the unit num bers as described in “Setting Up the Stack Conf iguration” in the Us ing t ...

  • Bay Technical Associates 400-ST1 - page 37

    35 5. Repeat Steps 1 to 4 f or unit 5. Figure 15. Remo ving Nonadjacen t Units 6. Renu mber the order of the units fo r the new s tack configuration (if desired). Y ou can renumber the unit num bers as described in “Setting Up the Stack Conf iguration” in the Us ing the BayStac k 450 10/ 100/1000 Ser ies Switch gui de. 1 = Base unit 2 = Last un ...

  • Bay Technical Associates 400-ST1 - page 38

    36 Upgrading the Ba yStac k 450 Swit ch Firmware The BayStack 450 switch firmwa re provides a code loa d facility that allows you to upgrade the f i rmware image ov er any switch port, in cluding any MD A ports. Y ou mu st upgrade th e BayStack 450 swit ch fi rmware image before y ou install the BayStack 400-ST1 Ca scade Module. Accessing the Firmw ...

  • Bay Technical Associates 400-ST1 - page 39

    37 3. After the BayStack 450 boot co de im age is downl oaded, click on V ersion 1.1.0 at the BayS tack 450 agen t link. Fo llow t he prompts t o downloa d the BayStack 4 50 agent image. The ag ent image filename is b450110 2.img Be sure to downl oad the BayStack 45 0 boot code image first , then download the B ayStack 450 agent image. Accessing th ...

  • Bay Technical Associates 400-ST1 - page 40

    38 • The port con nection to the load host canno t be throug h a MultiLink T runk. • During the load process, the ports are conf igured as follows: • T wi sted-pair ports: autonegotiation enabled. • Fiber optic ports: 100 Mb/s, half-dup lex. • Gigabit MD A po rt s: au tonegotiation dis abled, Preferred Ph y set to Right. Fo r detailed inf ...

メーカー Bay Technical Associates カテゴリー Network Card

Bay Technical Associates 400-ST1のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 400-ST1の取扱説明書
- Bay Technical Associatesの製品カード
- パンフレット
- またはBay Technical Associates 400-ST1の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bay Technical Associates 400-ST1の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bay Technical Associates 400-ST1の取り付け説明書、サービスマニュアル、簡易説明書、またはBay Technical Associates 400-ST1のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bay Technical Associates 400-ST1の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Bay Technical Associates 400-ST1デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBay Technical Associates 400-ST1を使用するのを助ける技術的文書のことです。説明書は通常、全てのBay Technical Associates 400-ST1ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bay Technical Associatesの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bay Technical Associates 400-ST1の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBay Technical Associates 400-ST1の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bay Technical Associates 400-ST1に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bay Technical Associates 400-ST1デバイスの基本機能を使うにあたってのヒント。 Bay Technical Associates 400-ST1のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bay Technical Associates 400-ST1に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBay Technical Associates 400-ST1のメーカー/サービスへの連絡先に関する情報。

Bay Technical Associates 400-ST1についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBay Technical Associates 400-ST1の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBay Technical Associates 400-ST1で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)