-
Delta 50-853 - page 1
INSTRUCTION MANUAL 3 H.P . Single-Stage Dust Collector (Model 50-852, thr ee phase) (Model 50-853, single phase) P ART NO. 902108 - 06-27-02 Copyright © 2002 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Cana ...
-
Delta 50-853 - page 2
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the product. Using the machine with r espect and caution will considerably lessen the possibility of personal injury . However , if normal safety precauti ...
-
Delta 50-853 - page 3
3 ADDITIONAL SAFETY RULES FOR DUST COLLECTORS WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJURY . 1. DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation ...
-
Delta 50-853 - page 4
4 UNP ACKING AND CLEANING Carefully unpack the tool and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened wi th ke r osene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces ...
-
Delta 50-853 - page 5
5 Fig. 5 Fig. 6 Fig. 7 Fig. 8 ASSEMBLING CASTER ASSEMBLIES TO BASE Align the holes in caster assembly (A) Fig. 5, with four holes in support stand (B) located on the underside of base (C). Place a lockwasher (E) Fig. 5 onto a hex head screw (D), insert the hex head scr ew through the caster (A), and thread into hole in base (B). Repeat this pr oces ...
-
Delta 50-853 - page 6
6 Fig. 9 Fig. 10 Fig. 11 Fig. 12 4. Apply a bead of silicone sealant around flange of chute (F) Fig. 9. Align holes in ten-hole gasket (G) Fig. 9, with mounting holes in blower flange (F) and press gasket onto flange as shown. 5. Align mounting holes in dust chute (H) Fig. 10, with gasket (G), assembled in STEP 4. Place a lockwasher onto a hex head ...
-
Delta 50-853 - page 7
7 Fig. 13 Fig. 14 Fig. 15 Fig. 17 7. Apply a bead of silicone sealant around flange of chute (H) Fig. 14. Align holes in eight-hole gasket (K) Fig. 14, with mounting holes in chute (H) and press gasket (K) onto flange as shown. 8. Align mounting holes in left hand drum (N) Fig. 15, with gasket (K), assembled in STEP 7. Place a lockwasher onto a hex ...
-
Delta 50-853 - page 8
8 Fig. 18 Fig. 19 Fig. 21 Fig. 20 11. Align two mounting holes in the top of drum support arm (T) Fig. 18, with two pre-drilled holes in drum (N) and fasten drum support arm (T) to drum (N). Place a lockwasher then a flat washer onto the hex head screw , insert the hex head screw thr ough the hole in upper drum support and drum and thread a hex nut ...
-
Delta 50-853 - page 9
9 Fig. 22 Fig. 23 Fig. 24 Fig. 25 ASSEMBLING FIL TER AND DUST COLLECTION BAGS TO DRUM 1. Hook the loop on the top of filter bag (A) Fig. 22, onto filter bag support rod (B) as shown. 2. Assemble extension rod (C) Fig. 23, into the end of filter bag support rod (B). Raise support rods (B) and (C), with filter bag (A) attached and place end of extens ...
-
Delta 50-853 - page 10
10 Fig. 26 Fig. 28 4. Pull up on each retaining clip (A) Fig. 26, and insert the dust collection bag (B) underneath each retaining clip to hold the dust collection bag in place. 5. Place the locking clamp (C) Fig. 26 around dust collection bag and dust collector drum and lock in place. NOTE: Make certain locking clamp is positioned in the channel o ...
-
Delta 50-853 - page 11
11 Fig. 29 Fig. 30 Fig. 31 ASSEMBLING DUST INT AKE POR T TO BLOWER AND MOTOR ASSEMBL Y MAKE CERT AIN THE DUST COLLECTOR IS DISCONNECTED FROM THE POWER SOURCE . 1. Align the four holes in the dust intake port (A) Fig. 29, with the mounting holes in the lip of flange (B) of blower assembly and fasten with four sheet metal screws (C). 2. Fig. 30, illu ...
-
Delta 50-853 - page 12
12 Fig. 32 Fig. 33 Fig. 34 Fig. 35 MODEL 50-853 SINGLE PHASE INST ALLA TION Y our dust collector is supplied with a motor and controller; however , it is not supplied with a power cord and plug. 1. T o connect the dust collector to a power system, remove contr oller cover (A) Fig. 34. 2. Bring the single phase power line through the access hole (B) ...
-
Delta 50-853 - page 13
13 OPERA TING CONTROLS ON/OFF SWITCH (Model 50-852) The “on/off” switch is located on the side of the motor stand. T o tur n the dust collector “ON”, push button (A) Fig. 36. T o tur n the dust collector “OFF”, push button (B). Fig. 36 Fig. 37 ON/OFF SWITCH (Model 50-853) The “on/off” switch is located on the side of the motor stand ...
-
Delta 50-853 - page 14
14 NOTES ...
-
Delta 50-853 - page 15
15 Printed in U.S.A. P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable · Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain part ...
-
Delta 50-853 - page 16
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ACRAFT ® , DEL T AGRAM™, Delta Series 2000™, DURA TRONIC™, Emc²™, FLEX ® , Flying Chips? ...
Delta 50-853についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもDelta 50-853の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta 50-853で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。