English dropdown-ico

Manual Carrier HUMCCLFP1025-A

12 pages 0.18 mb
Download

Go to site of 12

Summary
  • Carrier HUMCCLFP1025-A - page 1

    Humidifiers and Humidistat Installation, Start-Up, and Operating Instructions NOTE: Read the entire instruction in manual applicable to specific unit before starting the installation. This symbol → indicates a change since the last issue. SAFETY CONSIDERATIONS Improper installation, adjustment, alteration, service, maintenance, or use can cause e ...

  • Carrier HUMCCLFP1025-A - page 2

    Step 1—Inspect Package and Check Equipment Inspect contents of packaged humidifier. File claim with shipping company prior to installation if shipment is damaged or incom- plete. The package should contain: 1. Humidifier and media assembly 2. Humidistat 3. Template 4. Owner’s Manual 5. Warranty Certificate 6. Solenoid valve with bridge rectifie ...

  • Carrier HUMCCLFP1025-A - page 3

    Step 7—Make Water Connection If garden hose is not used for water supply: 1. Mount saddle valve on water line according to instructions supplied with valve. 2. Run 1/4-in. diameter (water line grade) tubing from saddle valve to adapter on solenoid valve and tighten compression fittings. IMPORTANT: If water pressure is higher than normal (60 psi), ...

  • Carrier HUMCCLFP1025-A - page 4

    Remember to provide clearance for maintenance and evaporator pad removal. To access pad remove top or bottom cover to expose assembly (turn knob counter-clockwise). Step 3—Prepare Plenum Opening (See Fig. 2.) 1. Use template for marking humidifier opening. 2. Tape in place on plenum making sure template is level. IMPORTANT: For humidifier to oper ...

  • Carrier HUMCCLFP1025-A - page 5

    7. Saddle valve assembly with adapter 8. Four sheet metal screws 9. Foam tape 10. Noise suppressor (use for water pressure over 60 psi) 11. Worm clamp for field-supplied drain tube 12. Humidifier maintenance instruction sticker 13. Carrier logo label Step 2— Select Location (See Fig. 7.) Humidifier must be installed on supply plenum only. If furn ...

  • Carrier HUMCCLFP1025-A - page 6

    Step 6—Mount Solenoid Valve The water solenoid valve should be mounted on top of humidifier enclosure. 1. To mount solenoid on top, see Fig. 10. a. Firmly press valve into the top inlet hole on enclosure. Seat valve flush against inlet hole. 2. If alternate mounting of solenoid is required, see Fig. 11. a. To mount solenoid on side, use 3/8-in. I ...

  • Carrier HUMCCLFP1025-A - page 7

    Step 1—Inspect Package and Check Equipment Inspect the contents of packaged humidifier. File claim with shipping company prior to installation if shipment is damaged or incomplete. The package should contain: 1. Humidifier and media assembly 2. Humidistat 3. Template 4. 6-in. damper 5. Owner’s Manual 6. Warranty Certificate 7. Solenoid valve wi ...

  • Carrier HUMCCLFP1025-A - page 8

    Step 5—Install Bypass Duct Attach field-supplied 6-in. diameter duct, elbow, or starting collar with field-supplied 1/4-in. zip screws. Install supplied 6-in. damper in 6-in. duct connector. IMPORTANT: On systems with central cooling, the damper should be closed during cooling season to prevent bypass air. Do not support weight of bypass duct fro ...

  • Carrier HUMCCLFP1025-A - page 9

    Step 3—Prepare Plenum Opening (See Fig. 2.) 1. Use template for marking humidifier opening. 2. Tape in place on plenum making sure template is level. IMPORTANT: For humidifier to operate properly it must be level and mounted on a vertical surface. 3. Drill four 1/8-in. holes in plenum. 4. Cut opening in plenum using heavy solid lines on template ...

  • Carrier HUMCCLFP1025-A - page 10

    compression fittings. Plastic compression nut supplied with float valve should not be torqued greater than 25 in.-lb. For copper tubing installations: copper tubing may be connected to float valve by using a field-supplied 1/4 to 1/4 in. straight- through compression union. Run copper tubing to 1 side of compression union and use a standard compres ...

  • Carrier HUMCCLFP1025-A - page 11

    5. Mount case horizontally over wires directly to wall using 2 long screws provided. 6. Replace faceplate and knob. Step 2—Duct Mounting (Low Voltage) 1. Locate humidistat at least 8 in. upstream of humidifier in return-air duct. If mounting near elbow area, keep device 6 in. upstream of elbow so element will be affected by normal airflow. (See F ...

  • Carrier HUMCCLFP1025-A - page 12

    Step 5—Operation When relative humidity falls to humidistat set point, the humidistat switch makes contact and starts humidifier. In some central unit humidifier systems, furnace fan must be operating before humidi- fier will start. An increase in relative humidity above set point will stop humidifier. Step 6—Checkout Place system in operation ...

Manufacturer Carrier Category Humidifier

Documents that we receive from a manufacturer of a Carrier HUMCCLFP1025-A can be divided into several groups. They are, among others:
- Carrier technical drawings
- HUMCCLFP1025-A manuals
- Carrier product data sheets
- information booklets
- or energy labels Carrier HUMCCLFP1025-A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Carrier HUMCCLFP1025-A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Carrier HUMCCLFP1025-A, service manual, brief instructions and user manuals Carrier HUMCCLFP1025-A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Carrier HUMCCLFP1025-A.

Similar manuals

A complete manual for the device Carrier HUMCCLFP1025-A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Carrier HUMCCLFP1025-A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Carrier HUMCCLFP1025-A.

A complete Carrier manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Carrier HUMCCLFP1025-A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Carrier HUMCCLFP1025-A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Carrier HUMCCLFP1025-A, that we can find in the current document
3. Tips how to use the basic functions of the device Carrier HUMCCLFP1025-A - which should help us in our first steps of using Carrier HUMCCLFP1025-A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Carrier HUMCCLFP1025-A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Carrier HUMCCLFP1025-A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Carrier HUMCCLFP1025-A?

Use the form below

If you did not solve your problem by using a manual Carrier HUMCCLFP1025-A, ask a question using the form below. If a user had a similar problem with Carrier HUMCCLFP1025-A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)